开云体育

Add ch processor and then import signals from

The script was pulled due to some issues with it, but VC-4 still does support dual NICs by creating the adapter.conf file in VC-4's conf directory and populating the file with the name of the NIC that you want VC-4 to use to reach out to XiO then restart the virtualcontrol service. There are also issues with using dual NICs where the OS will use the wrong NIC to send data to which will override VC-4's settings, but this can be fixed with a couple changes using NMCLI's interactive editor to set the USB-Ethernet NIC to never be the default for IPv4 and IPv6 communication.

The analog buffer will propagate value from input to output when enabled, the serial will not.
When you use buffers for feeding multiple room volumes from a single control/ramp, you want to use an Abuf for feedback, but a Sbuf for control.

It's a common mistake for beginners to assume Sbuf and Abuf are made for Analogs and Serial signals respectively, but in fact they are interchangeable and have different behaviours.

It does get confused on which NIC to use to "phone home". Definitely a problem when licensing with XiO Cloud. Pretty easy to fix with a couple of Linux commands though. You just need to change the metric number of the NIC so that the "phone home" NIC has a lower metric number, aka is used first.?

I have set up 6 systems in the last month or so with dual NICs and not using the script. They all seem to be behaving. I've found you have to make sure you run updates in the correct order but otherwise not too many issues.?

开云体育

Personally, I would not use a slider and just a gauge for feedback.? To answer you question, look at the difference between an analog and serial buffer.? You need both in this case.??

We set up a large resi system in our factory last year and as some of you may recall I was very happy with NAX.

Now the system is on site (very much a building site still) we have frequent power outages and still no AC in the AV Room.

Each night we power down the AV system down to avoid overheating when we lock the door.
Not something I'm happy about but this has exposed a few NAX issues.

The main one I'm trying to deal with but don't seem to have found a totally reliable solution is stream?initiation and getting the streams to start.

Source requirements are pretty basic:
5 X Sonos. 2 physically connected to one DM-NAX-8ZSA digital inputs, 3 connected to a second?DM-NAX-8ZSA digital inputs.

Last year when we set up at the factory, I simply went into the web UI and under NAX Streams set Auto Initiation on with default port of 5004.
This worked flawlessly at the factory, but since being on site we found the streams were not starting.

I've now implemented logic in simpl to start the streams and turned off Auto Initiation in the web UI.
This has mostly fixed the issue but very occasionally the streams will simply not start on first try.
I can force a stream stop then restart and it will then work.

In the NAX hardware def: Slot-07: DM-NAX-8ZSA —NAX > Slot-01: DM-NAX-8ZSA —TX> Slots-03 & 04:?DM-NAX-8ZSA — TX Source 3 & 4
I have defined the following:
* valid session name
* valid multicast address
* StartStream
* StopStream

I check in logic:
* I get a device ready pulse from Update Status.
* I have a valid multicast address
* Then issue the StartStream through a Truth Table when the above conditions are satisfied.
This logic works flawlessly and the StartStream digital is asserted.

I'm not checking I have a valid session name as this is set at startup & held in an MSP.

Anyone seen any of these issues and can offer any further suggestions?
I would really like to know why Auto Initiation no longer works, as I rather just do away with all the simpl logic.

Cheers

开云体育

Thank you

I have a?OLED65C1PUB control it using the Crestron Certified Drivers using ethernet.

On the online database there's a?OLED97G2PUA Driver that you could try and experiment with!

I'm in the process of honing in my skills which is very small. I'm controlling a C2N-AMP-4x100. What I can't seem to get working correctly is values updating as they should.

Volume buttons run to an Analog Ramp, analog out of that into an analog buffer thats enabled when the selected room is interlocked. Then the output of that runs to the "Room1_Volume" input of the amp symbol, and out of the "Room1_Volume_FB" into the same analog buffer (enabled by room selected Interlock) to pass to analog join 10 (Slider or gauge) to update the position as im holding the volume buttons. I cannot get the values to update on the slider or gauge ive tried both. I can use touch settable and that value will update but it will carry the same value when I select another room.

What is the best way to use one slider, 3 buttons (v+,v-,mute) to update the slider/gauge live, recall the volume levels of each "zone" if I were to switch rooms back and forth and not affect other zones reporting incorrectly?

Any update on the fix for this or word on what exactly isnt working when trying to use the script?

Ive read that it gets confused on which network to use to "phone home" and that the script settings also get wiped whenever the VC-4 gets updated. Not sure if either or both of these are true.
Would using the USB-Offline dongle fix this issue??

We have several projects based around the dual network design Crestron said was possible and find it extremely irritating that it is "no longer supported".

开云体育

If you have non X model, you can get second usb lan adapter (white ) from Crestron and IP what ever you want it. Not supported on X models (anything that has BYOD).

Thanks all

Lucky.? I've got integrators who have been waiting for months.? This is not an easy part to find and unfortunately when they go bad..... you know.