¿ªÔÆÌåÓý

ctrl + shift + ? for shortcuts
© 2025 Groups.io
  1. Crestron
  2. Messages
Expanded Topics Messages Polls
Date
Re: Panasonic PT-VMZ50 PJ Link

 

As it turns out, I have a project with a VMZ51 coming up and was going to post about the 'Crestron Connected Display'.
Is the consensus to use the PJ-link module vs trying to use the CCD?? I don't care, just don't want rabbit holes for just dealing with On/Off and input!!...:)
***Also, is the module recommended to use the 'PJLink Panasonic PT-FW300NT' found in the app market and dated 2010??

Also:
Mike - Thanks for the heads up on the IP-ID Hex/Not Hex issue. good to know...

John Gabler/others - Where you had the IP-ID 'Online', this seems similar to the issue with CEN-IO boxes and authentication. Proc w/ Auth shows device Online where the Cen-IO shows offline, thus you have to? run the 'SetCsAuth' command in the CEN-IO.? Does anyone think that this is the issue with this projector and the CCD???? ?It does seem to be a different animal comparitively...
Re: Lutron Homeworks QSX

 

There was/is a version of crestron firmware (I was doing it on a PRO4, not sure if 3 series are affected) that broke the Lutron integration.?

I can't remember the exact firmware version to avoid and not entirely sure if it's been fixed in a later version.?
I think I saw on here about the issue originally!
Re: Lutron Homeworks QSX

[email protected]
 

Hi Leonardo, I am currently struggling with communication between Crestron and Lutron QSX also so thought I'd reply.
As far as I understand, you enter the command processor id appropriately (Probably 1 if you only have 1 processor), IP address and user name and password which should match the credentials setup within the Lutron QSX.
I have an XPanel which pulses the "connect" pin of the module which starts the heartbeat of the module and also set the debug pin high so I can see the activity within Toolbox debugger.

I am continuously getting the following error:

LutronLeapCommLib1{ Reconnect!! }
LutronLeapCommLib1{ Connecting to 10.12.200.100 }
LutronLeapCommLib1{ SocketStatusChange: SOCKET_STATUS_NO_CONNECT }

After reading various threads, I've made sure to have Simpl Windows 4.18p, Crestron Database 211.05.001.00 and Device Database 200.175.001.00 as these were the versions used to create the Demo project on the Crestron Marketplace.

From there, I've just been pulling my hair out ... which isn't helping either. Anyone else able to advise?
Re: Lutron Homeworks QSX

 

You could always look for an older 3 series processor as well

On Jan 11, 2023, at 06:11, gbnet.hifi@... wrote:

?I think the crestron processor needs a licence for lutron and without the license installed will block ip control of any device with a MAC address that belongs to Lutrons MAC range

On 11 Jan 2023, at 5:44 pm, Leonardo Lagdameo via groups.io <lagdameo_leonardo@...> wrote:

?Hi Guys any one can help me how to control Lutronx QSX i used the module from application market and set all the parameters needed like username/password IP address of the lutron processor and follow all the commands in sample module.







Re: Lutron Homeworks QSX

 

I think the crestron processor needs a licence for lutron and without the license installed will block ip control of any device with a MAC address that belongs to Lutrons MAC range

On 11 Jan 2023, at 5:44 pm, Leonardo Lagdameo via groups.io <lagdameo_leonardo@...> wrote:

?Hi Guys any one can help me how to control Lutronx QSX i used the module from application market and set all the parameters needed like username/password IP address of the lutron processor and follow all the commands in sample module.




Lutron Homeworks QSX

 

Hi Guys any one can help me how to control Lutronx QSX i used the module from application market and set all the parameters needed like username/password IP address of the lutron processor and follow all the commands in sample module.
Re: Amazon Firestick Control solution

 

Great. Thanks for the help I will try these options
Re: Panasonic PT-VMZ50 PJ Link

 

I see you got PJ Link working so probably don't need to spend more time on it. But in case other people come across this thread were you using the oh so helpfully named "Crestron Connected Display" symbol which is actually Crestron Connected v2 or were you using "RoomView Connected Display" the older name for Crestron Connected and actually works with 90% of the device out there called Crestron Connected.
Re: Getting other than English text on a touch panel.

 

¿ªÔÆÌåÓý

I did an interface that could be changed between German French Spanish and English. A button on the tech page would switch between the languages.

I took my English text and translated with Google translate. You have to be careful with proper context etc but it works. The logic was simple¡­..just send the proper language text to the serial joins by whatever means you choose.


On Jan 10, 2023, at 1:42 PM, Rafa C via groups.io <rafa_climent@...> wrote:

?
For these cases, I have clients who want 3 - 4 languages in their panels, I use indirect texts, with custom modules with JSON or XML.

You can also use multiple serial send or similar

When select the required language, the corresponding text is displayed.

Kind regards
El 10 ene 2023, 21:09 +0100, Brad Wykoff via groups.io <bradwykoff@...>, escribi¨®:
Client is requesting to include a Japanese translation of the text on a TS-1070 touch panel.
My first thought was to use an English to Japanese translator, copy that into a Word Doc then use Gimp to modify to a PNG then use that image in VTPRO.

Any other suggestions would be appreciated.

Re: Getting other than English text on a touch panel.

 

For these cases, I have clients who want 3 - 4 languages in their panels, I use indirect texts, with custom modules with JSON or XML.

You can also use multiple serial send or similar

When select the required language, the corresponding text is displayed.

Kind regards
El 10 ene 2023, 21:09 +0100, Brad Wykoff via groups.io <bradwykoff@...>, escribi¨®:

Client is requesting to include a Japanese translation of the text on a TS-1070 touch panel.
My first thought was to use an English to Japanese translator, copy that into a Word Doc then use Gimp to modify to a PNG then use that image in VTPRO.

Any other suggestions would be appreciated.

Re: Adding Shure MTX Mute to SIMPL Program

 

Thanks Phil and Chris.

I think I may have bit off a bit more than I can chew and would appreciate a bit more help if you're feeling so generous.

On my test bench I've got VC4, a TSW-770, and my MTA Mute.
My MTA Mute has a static IP of 192.168.1.114

I've got a button with digital 2 for mute_press and mute_fb. On a toggle, I have mute_press connected to the clock and mute_fb on the output.

I keep thinking that I've figured it out, then I try and put it together and have it fail. Many of my issues are from failing to understand much of SIMPL and I'm working on that.
I'm guessing the SIO Tx should be the same as the TCP/IP_Client Tx, same for each's Rx.?
I thought I had understood Connect and figured it was just a matter of putting in the IP or IPID, but not sure how to do that without it being a variable.

When does SIMPL start to make sense?

Ben
Getting other than English text on a touch panel.

 

Client is requesting to include a Japanese translation of the text on a TS-1070 touch panel.
My first thought was to use an English to Japanese translator, copy that into a Word Doc then use Gimp to modify to a PNG then use that image in VTPRO.

Any other suggestions would be appreciated.
Re: Amazon Firestick Control solution

 

My Flirc files are in the files section if you want to give it a try.
Re: Panasonic PT-VMZ50 PJ Link

 

¿ªÔÆÌåÓý

Good to hear

?

__________________________

Mike Oberholzer - CTS

Systems Software Engineer?

518-650-7955

?

AUDIO-VIDEO CORPORATION

213 Broadway

Albany, NY 12204

?

518-449-7213

518-449-1205 Fax

?

oberholzer@...

?

From: [email protected] <[email protected]> On Behalf Of John Gabler via groups.io
Sent: Tuesday, January 10, 2023 2:22 PM
To: [email protected]
Subject: Re: [crestron] Panasonic PT-VMZ50 PJ Link

?

This email originated outside of Audio-Video Corporation. Please help keep our organization and our partners safe. It is up to us; think before you click.

Yep.? I used 0A in program and set the PJ to 10.? IPID is online and I still don't get Crestron Connected control.? I found the issue with my PJ Link.? Was using the wrong port.? The PJ Link module from the Application Market worked for what I needed.

Re: Amazon Firestick Control solution

 

I've used the Inteset on a couple of jobs and it seems to work well. Being able to use an existing IR driver was also a plus :-)

There have also been issues with the Fire TV going to sleep, which are addressed in the following article:

<>

--- On Tuesday, January 10, 2023 at 11:16 AM, Alex Teague wrote:

I've used the Inteset with XBox 360 IR code set out of the Crestron DB and it
works good. You need a USB y adapter in-line with the power supply though (in
the amazon description).

<>
Re: Panasonic PT-VMZ50 PJ Link

 

Yep.? I used 0A in program and set the PJ to 10.? IPID is online and I still don't get Crestron Connected control.? I found the issue with my PJ Link.? Was using the wrong port.? The PJ Link module from the Application Market worked for what I needed.
Re: Panasonic PT-VMZ50 PJ Link

 

¿ªÔÆÌåÓý

Just remember the IPID on the projector may not be HEX, so if in your program it is 10, the projector would be set at 16 for connected device setup

?

__________________________

Mike Oberholzer - CTS

Systems Software Engineer?

518-650-7955

?

AUDIO-VIDEO CORPORATION

213 Broadway

Albany, NY 12204

?

518-449-7213

518-449-1205 Fax

?

oberholzer@...

?

From: [email protected] <[email protected]> On Behalf Of John Gabler via groups.io
Sent: Tuesday, January 10, 2023 1:51 PM
To: [email protected]
Subject: [crestron] Panasonic PT-VMZ50 PJ Link

?

This email originated outside of Audio-Video Corporation. Please help keep our organization and our partners safe. It is up to us; think before you click.

Is there a module for PJ Link control or can someone post a properly formatted command?? I've tried the crestron connected and the projectors IPIDs are showing online, but not controlling them.? So I wanted to try PJ Link, but I don't think that I am formatting the command correctly.

Panasonic PT-VMZ50 PJ Link

 

Is there a module for PJ Link control or can someone post a properly formatted command?? I've tried the crestron connected and the projectors IPIDs are showing online, but not controlling them.? So I wanted to try PJ Link, but I don't think that I am formatting the command correctly.
Re: Anyone feel like helping me with some Http Post Commands ? #http

 

¿ªÔÆÌåÓý

are you familiar with C#? If so SIMPL# is a lot easier to do this.


On Jan 10, 2023, at 9:15 AM, Chris.estes@... wrote:

?I got at least one of the commands to work via postman, and this is the code snippet it output

POST /account/gettoken HTTP/1.1

Host: 192.168.0.171:4004

Content-Type: application/json

Content-Length: 59

?

{"email":api@...,"password":"password"}

?

So this is the command I am attempting

POST /account/gettoken HTTP/1.1\nHost: 192.168.0.171:4004\nContent-Type: application/json\nContent-Length: 59\n\n{"email":api@...,"password":"SKGi1qGHM0p"}\n\n


and this is a cURL example from the API guide .

curl -X POST \
? http://192.168.7.2:4004/account/gettoken \
? -H 'cache-control: no-cache' \
? -H 'content-type: application/json' \
? -d '{ "email":"api@...", "password":"myPwd" }'

Re: Pyng Hub with Sonos?

 

Thanks, I thought I remembered the updates killed it for pyng, just verifying so thanks.?
7861 - 7880 of 256292