¿ªÔÆÌåÓý

ctrl + shift + ? for shortcuts
© 2025 Groups.io
Date

Re: Marantz SR7015

 

Well if its that then you should be able to work around it or even turn it off if it gets turned on. I see theres commands for it in the protocol:
Dynamic EQ = ON
Dynamic EQ = OFF
Request Dynamic EQ Status
DYNEQ ON
DYNEQ OFF
DYNEQ ?


Re: Marantz SR7015

 

It is the Dynamic EQ (PSDYNEQ ?/ON/OFF) - if ON, the MVMAX dynamically adjust with volume level - the higher the volume, the higher the MVMAX goes, up to the set limit.

With Dynamic EQ off - MVMAX is always at whatever is set as the limit in the settings.

?

Dynamic EQ is basically advances "Loudness". It does improve experience at low levels.


Re: internal clock battery

 

I cannot speak for all Crestron products, but at least my CP3 has a CR2320 3V Lithium coin battery in it.? As a side note, I don't every recall a Crestron processor losing time completely it doesn't have power.? But without an Ethernet connection or ntp disable, the clock will eventually drift off time.


internal clock battery

 

Do RMC3s, CP3s, etc. and 4-series have a battery for keeping internal clock?


Re: Marantz SR7015

 

On Mon, Dec 19, 2022 at 01:31 PM, <zac.sparrow@...> wrote:
It may be related do dynamic EQ/Dynamic volume/Audessy calibration etc.
That's interesting! I hadn't thought of that...


Re: Marantz SR7015

 

3 series but this has nothing to do with the processor. I am monitoring the AVR with putty. The good news is it is at home, so I should be able to figure out what's going on.

It may be related do dynamic EQ/Dynamic volume/Audessy calibration etc.


DMPS3-300-C

 

Folks? -?
I have a DMPS3-300-C that is way out of warranty and it has gone sideways. I suspect the SD Card Image is bad. How would one go about getting the image?

Best regards
AV Programmer
End of Line


Re: Marantz SR7015

 
Edited

Yes, this kind of behavior was what I experienced and was the catalyst for the thread a couple months ago!!
Are you using a 4-series processor?

In my case the project started with a 3-series (waiting for the CP4) and all was good, like it has always been with the DM Avrs... we changed to the CP4 with the (then) latest FW, cp4_2.8000.00010.01.puf.
I didn't have time to deal with it so I went to 'fake' feedback...? ?
My thinking is that this could possibly be on the Marantz side, but it's weird.

I'd love to see some understandong of the root of this and know the Proc and FW that you see this behavior with...
TIA!


Re: Marantz SR7015

 

I think I have discovered an issue with the MVMAX. It seems to change on it's own, based on signal source type. Notice below Putty exchange:

?

MV? //volume poll after power on

MV48
MVMAX 80 //as expected, that is the 0db set in settings
MV14? //Crestron direct volume set
MVMAX 80 // good
MSDOLBY AUDIO-DD? // I started DolbyDigital source (cable TV)
PSDRC OFF
SSINFAISSIG 03
SSINFAISFSV 48K
PSLFE 00
PSBAS 50
PSTRE 50
PSTONE CTRL OFF
MV?

MV14
MVMAX 695 // Ah?

MV?

MV14
MVMAX 695 //WTF?



MV695 //I am setting volume to alleged new max
MVMAX 80 // Seriously?
MVUP

MV70
MVMAX 80

?

I will keep digging.


Re: Write file to FTP server

 

You can use the console symbol along with the command fput.

This is the command format:
FPUTfile [url] [local_path] {username:password} {proxy}
? ? url - fully qualified URL to the file being uploaded to the server
? ? local_path - path to the source file in the ROM
? ? username:password - optional access credentials to the server
? ? proxy - optional proxy in the form of url
?
Some added information:
FPUT and FGET can handle FTP, SFTP, SCP, and HTTP(S)
path is: ftp://servername/foldername/filename or http(s)://servername/foldername/filename
?
A complete command might look like:
fput ftp://192.168.0.110/PublicComments.txt \rm\group1\public\2017-12-04\PublicComments.txt "username:userpass"


On Sat, Dec 17, 2022 at 1:58 AM <jclaerebout@...> wrote:
Hi

Does anyone know how to write a file to an FTP server from the program like writing to \\NVRAM ?



Write file to FTP server

 

Hi

Does anyone know how to write a file to an FTP server from the program like writing to \\NVRAM ?



Re: Lightech LET 75-24-R

 

It would *appear* that this unit is an electronic transformer. have you tried hard-setting the 2DIMU8 to ELV for that load instead of using the adaptive mode?


Lightech LET 75-24-R

 

So, I have a lighting system with these drivers and they dim like crap.? 2DIMU8 as well as a DELVEX.? This unit is 24VAC output.? Does anyone know of a replacement with 0-10V control?


Re: Tsw 750 loosing touch #tsw

 

no I have not but we sent some back to crestron and they said needed to replace screen
these Tsw's were in questionable locations(almost outdoors) near the Ocean, But now seeing it in environmentaly controlled location


Re: Marantz SR7015

 

I notice in the control protocol there are 3-4 different channel level commands. Some of them make sense, for example LFE level only, could mean adjusting the source LFE level without touching the bass frequencies sent to sub out when main speakers are set to small with cross over. Others have level for 7.1 analog in or stereo in etc.

However, these 2 seem completely redundant or not explained properly:
Channel Volume ? ? C UP CVC UP<CR> CVC 50<CR>
Center ---CENTERch ? C DOWN CVC DOWN<CR> CVC 50<CR>
? **:38 to 62 by ASCII , 50=0dB ? C ** CVC 50<CR> <-

vs

Center Level Adjust ? ? CLV UP PSCLV UP<CR> PSCLV 50<CR>
? ---Center Level¡¡Adjust ? CLV DOWN PSCLV DOWN<CR> PSCLV 50<CR>
? **:38 to 62 by ASCII , 50=0dB ? CLV ** PSCLV 50<CR> <-
? Return CLV Status ? CLV ? PSCLV ?<CR> PSCLV?<CR>
PSCLV ON<CR>
PSCLV 50<CR>


Re: Tsw 750 loosing touch #tsw

 

Have you tried re-flashing the FW? just something to try...
If you're not updating, just reloading the same version, make sure to add the 'All' suffix...
EX:
puf?tsx_1.501.0013.004.puf all

Worth a try...


Tsw 750 loosing touch #tsw

 

So encountering more and more tsw750 that are loosing top and bottom 3/4 inches touch sensitivity--so even in diagnostic page the Calibrate button can't be pushed--in info page tools "setup" ther is a calibrate button but it is greyed out--redrawing Vtpro projects getting shorter and shorter LOL. I thing it's only a one year wait for new TP now


Re: Sony STR-ZA1100ES direct volume setting

 

Thanks you Chris, that looks perfect. I appreciate the help!

-andy


Re: Truth table not working

 

¿ªÔÆÌåÓý

?If you don¡¯t care about Envy_AR_300 ?(all x¡¯s on input row) why have it in the truth table?¡°

?

Mh, might be a leftover from permanent changes on the code. There should actually be an ¡°H¡± in the leftmost column.

?

¡°Are the output signals being jammed elsewhere? e.g. within a module¡±

?

I think that was it. The plan was to trigger steppers with the output of the TT. However, it seems I got the same signal being part of the stepper, so it got jammed¡­

?

Thanks for responding. I learned a lot about TTs and probably became a fan of it like Lincoln. ?

?

Cheers,

Thorsten

?

Von: [email protected] <[email protected]> Im Auftrag von MSTC
Gesendet: Donnerstag, 15. Dezember 2022 15:56
An: [email protected]
Betreff: Re: [crestron] Truth table not working

?

If you don¡¯t care about Envy_AR_300 ?(all x¡¯s on input row) why have it in the truth table?

?

From: <[email protected]> on behalf of Thorsten K?hler <thorsten.koehler@...>
Reply-To: <[email protected]>
Date: Thursday, December 15, 2022 at 7:05 AM
To: <[email protected]>
Subject: Re: [crestron] Truth table not working

?

Try that share:

?

Cheers,

Thorsten

?

Von: [email protected] <[email protected]> Im Auftrag von Lincoln King-Cliby via groups.io
Gesendet: Donnerstag, 15. Dezember 2022 14:34
An: [email protected]
Betreff: Re: [crestron] Truth table not working

?

If you were able to post a link to a screen shot of the TT and Debuger with states of the inputs/outputs to the TT we could probably figure out what is causing the pulsed behavior.

?

I use TTs pretty extensively (sometimes I feel like more than I should¡­) and haven¡¯t ever seen an output pulse that I wasn¡¯t expecting to have pulsed

?

--

Lincoln King-Cliby, CTS, DMC-E-4K/T/D
Commercial Market Director
Sr. Systems Architect | Crestron Certified Master Programmer (Diamond)
ControlWorks Consulting, LLC
Direct: (+1)440.771.4807 | Cleveland: (+1)440.449.1100? | Boston: (+1)508.695.0188 | DC: (+1)202.381.9070? | Fax: (+1)440.449.1106
Crestron Services Provider | Biamp Authorized Independent Programmers | Extron Qualified Independent Programmer

?

From: [email protected] [mailto:[email protected]] On Behalf Of Thorsten K?hler
Sent: Thursday, December 15, 2022 8:04 AM
To: [email protected]
Subject: Re: [crestron] Truth table not working

?

Hm, all of the inputs are static, not pulsed.

That?s the reason why I was expecting the outputs to be static as well. That?s not an issue for my use case since I want to outputs to just trigger a stepper anyway. But still interested why they are not static although they should be¡­

?

Cheers,

Thorsten

?

Von: [email protected] <[email protected]> Im Auftrag von Lincoln King-Cliby via groups.io
Gesendet: Donnerstag, 15. Dezember 2022 13:41
An: [email protected]
Betreff: Re: [crestron] Truth table not working

?

A TT will hold the last matched state ¨C if you¡¯re seeing the outputs pulse its because when the input transitioned from high to low it matched a column to drive the outputs low. E.g. it¡¯s pretty typical to end a TT with an all ¡°X¡± input check that sets all outputs low (e.g. ¡°if you didn¡¯t match any of the prior rules, clear all outputs¡±) and if you ended a TT like this a pulsed input will result in a pulsed output.

?

--

Lincoln King-Cliby, CTS, DMC-E-4K/T/D
Commercial Market Director
Sr. Systems Architect | Crestron Certified Master Programmer (Diamond)
ControlWorks Consulting, LLC
Direct: (+1)440.771.4807 | Cleveland: (+1)440.449.1100? | Boston: (+1)508.695.0188 | DC: (+1)202.381.9070? | Fax: (+1)440.449.1106
Crestron Services Provider | Biamp Authorized Independent Programmers | Extron Qualified Independent Programmer

?

From: [email protected] [mailto:[email protected]] On Behalf Of Thorsten K?hler
Sent: Thursday, December 15, 2022 2:36 AM
To: [email protected]
Subject: Re: [crestron] Truth table not working

?

OK, forget it, guys.

It?s working. I was just under the impression that the outputs of the truth table would stay high after evaluation, but they are just pulsed.

?

Cheers,

Thorsten

?

Von: [email protected] <[email protected]> Im Auftrag von Thorsten K?hler
Gesendet: Donnerstag, 15. Dezember 2022 08:29
An: [email protected]
Betreff: [crestron] Truth table not working

?

Hi,

?

i?m trying to evaluate a set of signal combinations and would like to use a truth table for that.

The thing is that it doesn?t do anything¡­

I?ve got 3 input signals and 3 output signals.

I?ve added all possible combinations for the inputs and then set the ¡°H¡±/¡±L¡± for the outputs to my liking.

However, the output signals don?t change at all, regardless what happens to the input signals.

?

Anything i?m missing here?

?

Cheers,

Thorsten


File /Sony STR-ZAxx v1.1_archive.zip uploaded #file-notice

Group Notification
 

The following files and folders have been uploaded to the Files area of the [email protected] group.

By: ckangis <chris@...>

Description:
Module for Sony ZA-series AVRs (x000 and x100 models). Has updated CLZ to fix comm's issue from 2016 and also updated for the NewtonSoft/v200+ database change