开云体育

You can wrap an oscillator in a standard SIMPL module and load it into D3pro as a logic module - hooking it up in D3 is a faff, but that would be how I’d do that (off the top of my head)

Greetings all. I am trying to figure out how to get a pulsing feedback from D3. Similar to when a lighting load is dimming and the led blinks. I want certain specific loads to do that whenever the load is on. Any help would be great !?

@ckangis, I'd look at the Rally Bar with Extension Mics in that Boardroom space. Sets you up nicely for Logitech's Sight (center of table camera/mic solution) coming mid-'23 as Sight will require Rally Bar (or Mini) for some more advanced features; like auto handoff of users between cameras as they focus their attention between fellow participants across the table and persons remotely on the display at front of room.

In the Theater you'd most likely want to look at Logitech's Roommate as it's meant to be dropped into a system where a DSP is needed for wireless mics, zoning out audio, etc. Supported partners include QSC, Biamp, Nureva, Shure, and continues to grow, but those relationships allow for easier access to resources with those vendors in addition to the confidence of knowing you'll be supported should anything odd arise. The camera could be a Logitech Rally Cam, Rally Bar (in USB mode) or any other supported 3rd party camera. FWIW, I find this type of environment funny for Zoom calls too, but with AMC now renting out their theaters for this very purpose, I suppose it's being adopted to a certain degree.

For the sake of transparency, I am currently a Logitech employee who was previously a TD at Crestron for the US West Coast. I've spent the better part of 20 years in the integration space, as an engineer and programmer.

Put the image into /html/ on the processor.

If using 4-series, or 3-series with authentication off:
Use the path: http://processorip/image.jpg?

If using 3-series with authentication on:
Use the path:?http://user:password@processorip/image.jpg?

I don't have Windows anti-virus, I use another third party software.
I notice that it does that on new programs as well, only once. It's possible that it could be related to a virus scan of some sort, thanks for the tip.

Has anyone successfully controlled a Marshall Electronics CV730 PTZ over the network?

I Called Marshall Electronics and they told me I need to use the "SONY SRG-300SE IP v1.0" Crestron module with UDP/IP Communications Port 52381.

?

This is working fine for PTZ but I have no preset recall or store functions, and the module itself does not have a pwr on/off. I also cannot find any commands they have published for this method, they just gave me a standard Visca document.

I also wrote a bunch of code with the CGI commands they have published on their website and the camera rejected all commands.

Any insight to this is appreciated.

- Nate

Cody, or anyone who might know, are CEC command strings entered in the standard format, e.g., \x4F\x82\x20\x20 ?

I've tried various commands that I'm certain are correct, but I get no response going through the ConfigureRX_CEC module.? That module's digital On and Off commands do work, but I also need to send input commands.

Thanks in advance.

I need to use a serial string from SIMPL to trigger this.
Are there any formatting requirements for the JPG image in order to display it on the panel??
Would the exact string be something like?//processor ip address//User//image.jpg in SIML sent to the serial join on the panel....this is what I am trying and it does not seem to work, maybe I need a different port number in the IP address or and http: in front....I am not sure.

Is it possible to store an image on a processor PRO3, then bring it up on a panel? Example image loaded to //processor ip address//User//image.jpg
What would the serial string on iPad Crestron Go app on a dynamic graphic be?
No security is enabled on the processor?

Hi Jeroen,

no haven’t tried any of those!?

I will give them a try and report back, thanks!?

Hi Thorsten,
Have installed quite a large number of the range, and was trying to think of the ip ones.? However, I think everything i have done has been rs232.?
That said, i believe the info required is in the manual (look around the rs232 communication).? From memory it is using PJLink protocol.
I think there is a module in the application market for it, although i haven't used it and only written out the the required info from protocol for past PJLink projector setups i have done

Regards
Matt

I’ve seen it and it will work fairly well until you rotate the phone. Crestron is aware of it and as far as I know, has not solved it yet.

AH! Powered by USB!!? Didn't think of that...Thanks Paul, I'll try that. I just need to do some bench testing...

Hi Nathan,
Thanks so much for the follow-up!!?
Yes, I peeked at logitech (I've generally always really liked LT products) and as for sound bars I definitely think that they're dialed (Of course, Crestron's solutions are LT!!)
I have a couple Boardrooms with 16-18 people around a large table so I'd need some sort of mic array setup/DSP or other...
I also have two AmphiTheaters, which presents a specific 'concept' problem with Zoom, i.e. do they really want to have the entire space audio mixed to the call? or just a couple handheld for the speakers, etc...

Either way, my initial impression was that LT was not playing in that space...I'll have to dig deeper if you think that they'll be able to handle it...
TIA!!

Yes, I've seen this. In my testing it seems to happen when you close the app and let it run in the background then open it again. Doesn't seem to happen when I force close the app every time.

According to https://www.crestron.com/Products/Lighting-Environment/Climate-Control/Thermostats/HZ-THSTAT-W
- Power Consumption: 3 W @ 24VAC
- Hidden USB port can be used to power and preconfigure the thermostat (Micro B female, USB 2.0 computer console port for firmware upload, temporary power, and device configuration). Believe it indicated on rear of unit, but didn't see any drawings as to exactly where.

"Yealink does look like it has a pretty scalable range of products, which I don't think that Logitech has (important because I have a few larger rooms to deal with...)"

What specifically are you looking for? Logitech's VC focused catalog has met the scope requirements of most space types I've come across. They've opened up to 3rd party DSPs (Biamp, QSC, Nureva, Shure, etc) through the Roommate appliance and have a strong showing when it comes to soundbar designs. Optical camera lens options, cloud based management platform, options between appliance (Android 10) or Windows based computes and a slew of subsidiary companies which they draw knowledge?and experience from. Plenty of new UC focused solutions both in hardware and software coming in the new year for both in-room and personal use. Just some off-the-cuff thoughts for your consideration.

Hi All,
I'm getting a report from one of my dealers about a display issue with the GO app and iOS 16.x.
It seems that when opening the app, the graphics are shifted partly off-screen and/or are scaled incorrectly...
Closing and reopening seems to fix it, until you open again and then you're back to square one...

Anyone else see this kind of issue???
TIA!