--

I'm implementing the DMP 128 plus module for the 1st time and I'm not connecting to the device.? IP table shows device as online. ? Debugger shows a reply from the DMP that says "password:" I'm sure someone here has seen it before and has a quick answer that can prevent me from spending hours researching and calling tech support.? Thanks in advance.

Have CP4r connect to two DIN-CEN-2POE (amongst other things). Whenever power goes out to them, none of the attached devices work when power comes back. The rest of the system works fine. They seem to have IP addresses/etc. The only fix I've found is to restart the switch (not router!) they are connected to. It's a Ubiquity 48POE pro. Any ideas how to remedy this?

The processor's IP table shows the cen is connected. The cen's IP table shows the processor is disconnected.? Any advice??

Curious if anyone has worked on this? I’ve been controlling OBS using the command line interface via SSH. This is reliable for sending basic commands like scene switching, but does not provide feedback. I would write my own module, but need a websocket client, and I’m not a # programmer.?

Does this tool connect to programs running in multiple slots in a processor reliably and show correct debugging info?? Also, is there support now or in the future for VC4?

Oh, now I understand why I could not add the TST-902 Crestron Device to my SIMPL project, as it requires RF to work!?

Hi,
The wifi connection on the TST is only for the toolbox.?
The communication with the master happens via an RF gateway. I always use the CEN-GWEXER. That is an ethernet device, the TST must be assigned a RF ID and with that ID aquired to the gateway.

1. I'm using XPanel 2.0 (version shown is 2.16.05), it's displaying the main page and subsequent pages fine, but it's not loading any controls.

2. Why does the TST-902 connect via an RF gateway? (there's no ER gateway right?) I use wifi and I can upload and display the project, and Crestron Toolbox is also able to communicate with it. Just that it doesn't display the subpages which are all working perfectly well with TSW-752.

+1 for the C5 debugger, it’s been a game changer for me, haven’t been near Toolbox in months and then only to work with a 2-series
It’s got great features (multiple concurrent debugger sessions for example), device connections are very stable and the support is superb, it also doesn’t crash every 10 minutes
Best money I’ve spent….

What is required in c# for this project?

Does your program have a separate IP-ID for the xPanel and the 902?? Or are you trying to use the same IP-ID (752) for these other devices?
I have found an issue with trying to run more than one device on the same IP-ID, particularly the TSW panels do not seem to like sharing their IDs...
If this is your situation, try disconnecting the TSW, rebooting the program and trying one of your other interfaces...

Ideally, your program should have separate IP-IDs for each UI...

I can say with some authority that a lot of people have tried it. We have great service and welcome all suggestions for changes, fixes, and ideas for features.

"...it wants"...funny

I mistakenly typed the proper model number.

I've noticed any search function on the Crestron site is a few years away from primetime it seems.? Just venting when in the middle of firmware hell when trying to get out of client's home ASAP.

A few things to check

(1)? Are you using X-panel or X-Panel 2.0 (Smartgraphics)?
(2)? Do you have the TST-902 connecting through an ER Gateway?? (ER Gateway should be showing as online in the IP Table and the 902 should be paired to the ER gateway)

I only coded Crestron almost 10 years ago and not familiar with the new environment, I'll need some perhaps very basic help here.

?

In my project, I have a main page, and a few pages and a few subpages. In one of the pages (call it Pg1) I have a few buttons, and I also created a subpage containing some simple controls like buttons.?

?

On my wall-mounted TSW-752 touch panel everything is working fine, but when I try it out on my XPanel and TST-902 (a portable touch panel), this Pg1 does not show up the buttons and the subpage. I was wondering what could be the problem I'm facing? Why my TSW-752 working flawlessly yet on XPanel and TST-902 these objects don't show up at all??

?

It maybe a really stupid question, but please bear with me, I have tried many times to try to solve it to no avail.

@ckangis - do you use it, do you recommend it?

Has anyone tried this third party debugger?

开云体育