开云体育

Try adding this to the end of your serial string:?

.....................?rtsp_tcp=no
So my original link supplied from the Unifi's Protect was:
Original:??
rtsps://192.168.x.xxx:7441/UvyHyFrPHqzN?enableSrtp
Modified:?
rtsp://192.168.x.xxx:7447/UvyHyFrPHqzN?rtsp_tcp=no

Here are some notes I have saved in OneNote. Might be helpful.?

Camera Stream Integration?

Camera Configuration?

To configure the camera, refer to the information below.?

Configure either the H.264 or the MJPEG video stream according to the recommended?

maximum resolution in the Video Streaming with Crestron Touch Screens online help article OLH 5195.??

?

Generic streaming information:?

? Configure the camera JPEG snapshots so that they do not exceed the maximum

resolution as follows: List View: 1920 X 1080 16:9, Grid View: 640 X 360 16:9, and Hi-Res Grid View: 1920 X 1080 16:9

? Make note of the correct URL for the camera, as this URL will be used in the program.

?

H.264 information:

? Set the I-Frame rate of the camera as low as possible.

? Set the Frame per Second (FPS) rate as high as possible to improve the connection

time from Crestron platforms.

?

UDP versus TCP for H.264 streams?

? To reduce latency when connecting and streaming from an H.264 stream, the preferred connection method is UDP.?

? The best way to make sure the touch panel is using UDP is to add “?rtsp_tcp=no” at the end of the rtps:// URL, for example:?

○ rtsp://user:pass@IPADRESS:PORT/live.sdp?rtsp_tcp=no.??

? However, if the network is configured in a way where UDP is not supported when the camera is on a different subnet than the touch screen, the TCP method must be used, for example:?

○ rtsp://user:pass@IPADRESS:PORT/live.sdp?rtsp_tcp=yes.?

?

Streaming Buffer Size

? When viewing IP videos, a buffer is needed for the incoming video. If the buffer length is reduced, the switching time is improved.??

? If there are any network limitations, video distortion may occur. Test and then use the lowest possible buffer setting that will work in the network environment. If video distortion occurs or if the stream appears choppy, then raise the value until the problem is alleviated.??

? The default buffer length for touch screens supporting the EEV object is 1,000 milliseconds (ms). Valid values are from 25 ms to 2,000 ms. The buffer length can be adjusted by using the following console command to set the length in milliseconds:

○? MEDIABUFFERLEN.?

I use them all the time.? Very helpful for keeping a basic design that just needs minor tweaking depending on the project (visibility joins on sources for instance).
According to Crestron, visibility joins are faster than using the analog join for number of items.? It also allows you to hide items in the middle of the list.? Also, according to Crestron, the list will draw faster if the "enable background" is checked.? I never enable it though but according to their tests, it draws faster.? "according to Crestron" are statements made at masters years ago when SRL first came out so maybe that's changed but I doubt it.

A big gotcha that I don't think ever was fixed, even though it was discussed numerous times with them, is the problem where if you have a SRL, say a menu, and you press an item on the menu, if you switch to a new subpage while the press join is still high, the touchpanel will continue to keep that signal high.? As an example, you have a SRL menu for presentation, audio conference, video conference, and settings.? The user presses the button for settings.? While pressing it, the touchscreen changes to the settings page and then the user releases his finger.? In debugger the settings join will be high.? So when they press the menu button again, it appears nothing happens.? In reality, the menu subpage opened, the join for settings was high, so the menu closed and the settings page opened.? The band aid fix courtesy of TB Canada is to do a lwp and trigger the page changes on the release.? So you would put the press on the [trig*], put a 0 on the trig, and the on the out, it would trigger your page change.? I've done that for years and haven't had any issues with SRL latching high phantom presses.? Pretty much if the press results in a page/subpage change, I just trigger it based off the release just to be safe.

Theres an analog input Scroll_To_Item on the SRL in Simpl, but I dont know how that would help to speed it up

Hi Jay,
im using H&T sensor only as a temp probe but i have 2 questions:
1 - i see on console temp have one decimal, it is possible to have out module also?
2 - maybe my mistake somewhere, H&T push me info but i would have expected every celsius degree change but is not so. Now a'm thinking powering H&T every time i need temp feedback using power like polling, any advise?

many thaks in advanced
antonio

What you are doing should work. I checked the unifi cameras.? ?I do have the snapshots turned on (you can access it at the camera ip address as )

My guess is you have accidentally removed too much from the stream URL.

Can you grab mpv or some other player, and try the actual stream URL you have entered into crestron?


Otherwise, check the crestron logs and see what they say.

Title says it all.

Thanks.

Daniel,
Is that a console command, or were you just clarifying your previous post?

scroll_To

I wonder if there's a way after an update to force a load so that it would perform better on the initial use...

Interesting! So this module requires communications to a service, even after initial setup?? I get that there are updates to be had over time, but if the service is off-line do the existing presets stop working? even with the old list?

If so, that gives me the creeps, as I'll never recoup losses from Weather App issues over the last year!!...:)
I should change my business model to a Loss-based format! HaHa!!

Have you made sure you're at or under the android app maximum resolution and frame rate?? It looks like the app is significantly lower for h.264 and MJPEG (1280x720@15fps) than the 60 series (1920x1080@30fp).? I've had problems in the past with resolution & fps mis-matches across interfaces.

Try this - while you streaming object if active on the page subpage, press the tablets power button to turn off screen then wake it up. This has worked for me in the past - it was required often to get it going.?

Yea I sent a bug report years ago to tech support and their response was to just ignore it.?

Check the camera stream to make sure it is set to H.264 and NOT H.265. I have seen a few devices (Speco, ICR) that when they are rebooted they revert the stream back to H.265 braking the stream- its quite annoying.?

They definitely slow down pages a bit even on xx60 series panels and are sometimes slow to populate on new panels as well. But they are a great tool and generally once they load they work well

Aside from when the service has outages, it works pretty well. Its fine on 310s but we have alot of jobs with 302s and it will not fit on there correctly. Which sicks as on those we are using V1 presets which are known to bring a processor to its knees. The V2 once in a while will not find any channels in a search but again I think thats provider issues. I know people with Directv have complained about channel lists that do not include local channels- I dont know if that has been fixed or not.?

Ok, need to change my plea hear.? Can someone please direct me to a document that provides a procedure for tying a unifi camera to crestron home?

Comment that sh*t out.

Hi,
I have a Crestron system with a TSW762 & a Android Tablet running the Crestron App. WE have been running the Crestron Embedded Video Smart Object in both to view the? RTSP stream from their PTZ Camera. Originally it worked fine; now we are unable to "see" the stream on the Android Tablet. Attempted to go through Crestron Support, but nothing they recommended resolved issue.
1. We resized the window for an exact 16:9.
2. Tries both H.264 & MJPEG Viewers
3. Deleted & reinserted the Embedded Video Control module
4.Tried both the "Stretch" & 16:9 settings for aspect ratio.
5. Confirmed with Video LAN App to confirm that the URL for the stream is working correctly.
6. We have no issue with the Embedded Video Smart Object on the TSW762 touch panel.
Any advice is appreciated. - Ken

beware of scrolling direction because you can't put objects in an SRL that move in the same direction.
/g/crestron/topic/unable_to_show_controls_on_a/89166354?p=,,,20,0,0,0::recentpostdate/sticky,,,20,2,0,89166354,previd=1645032624330230798,nextid=1644770297846019860&previd=1645032624330230798&nextid=1644770297846019860