Keyboard Shortcuts
Likes
- Crestron
- Messages
Search
|
Re: Dish Network
Got a call from Dish Custom Integration team today. They advised they are working on the issue and suggested a couple of things:
1.) I was not aware there is a secret menu to assign a static IP on the unit itself. I know most of us get around this by allocating IP by MAC address binding. Here are the steps to get to advanced menu for IP Settings, try setting static IP, DNS, etc. instead of MAC binding: Go to Menu>Settings>Internet then go to the advanced tab (Skip this last step on the Wally)
On a 40.0 remote press: Recall, Recall, Play
On a 50 or 52 remote: Recall, Recall, Play/Pause 2.) I'm currently using module 1.1 on the application market and they recommended I upgrade to the 2.0 module available at??As far as I know, this module cannot be used on anything other than a Crestron Home setup. Can anyone confirm? Please update here if any of the above recommendations work for you guys. Look forward to your feedback. |
|
Biamp Tesira Modules 3.2 - Crestron Application Market is down
Under the circumstances I hope this is ok to post.? If not the moderator can remove this.
I have just been on the phone with TB and confirmed that the Crestron Application Market is down. Modules can be put into your cart but you can not actually check out.? When you try to check out you wind up at a blank white page.? They are working on it but do not have an firm ETA on when it will be back up.? This was also reported earlier on the Facebook Crestron group.? Would anyone be willing to send me the Biamp Tesira 3.2 modules that may have already downloaded them? Thanks in advance, |
|
Re: What brand of NVR do you sell?
I sort of hate to say it, but the SnapAV LUMA product line is pretty good, both in hardware and software/app, and the cameras are generally 'a snap' to get streaming on TSW panels...
It seems to be one of the few of their lines that have gotten solid commitment to quality and features... |
|
Re: Topics in Home Automation - New Article in Residential Tech Today
Sorry only cloud control without feedback.? However, there are discrete open/close commands which really works around many feedback issues.? Especially compared to tying a relay in parallel with a wall mounted garage controller that just toggles the door open/close.?? ?I personally use a one of these? connected wirelessly to a non-alarm zone on an integrated security system to provide true feedback.? It is much more reliable?than worrying about whether a cloud service really knows what is going on and even provides feedback if the garage door is released from the opener and manually opened. Unfortunately, you can only implement a module based on what the manufacturer provides in terms of an API. Jay On Wed, Jan 6, 2021 at 8:06 AM <zac.sparrow@...> wrote: Local or cloud control? I know you are not a fan so hoping it is local.? |
|
Re: SIMPL+ Compiler bug
Nice catch on the explanation -- I hadn't even thought of that (and clearly Crestron didn't either!). On Wed, Jan 6, 2021 at 1:22 PM Steve Kuehn <steve@...> wrote: Thanks for the heads up on the brackets causing the issue.? I went ahead and updated all my code to use the method you described and it fixed my issues.? |
|
Re: LG OLED 232
I think that is what we are going to have to do on this one.
CEC isn't an option with this one and I have had similar experience with IP not working 100% of the time on LG. ?I've done plenty of LG displays, both commercial and consumer, over 232 in the past, but it seems like the latest consumer model just isn't going to play nice. |
|
Re: What brand of NVR do you sell?
I'm looking into a solution with Synology NAS and using the DS Cam app.? I had a co worker that highly recommended this setup.? Only downside I'm seeing is there are software licenses required per camera and of course, this is a consumer product so no profit margins.? But the app UX looks to be much better.
|
|
Re: LG OLED 232
So for what it¡¯s worth, we just did two of these exact displays and could never get the 232 to work. Tried everything including usb to 232 adapter. ?Never found a solution to keep the port awake. ?We then switched to IP control with WOL to power the display on...this worked pretty well 95% of the time. ?Once in a while the WOL would lock the display up and the only solution was to unplug power. ?Ended up discreetly mounting an IR LED in the cabinetry, ordered a naked high output LED. ?If I remember correctly the IR receiver on the TV is in a cosmetically bad spot and a standard bug looked terrible.
|
|
Re: LG OLED 232
I use RS232 to control my LG OLED65C8P. The connection has been rock solid for me. It's connected to Digi PortServer TS 8. I not think I had to make any special changes to the TV's default settings.
My only grief is that the TV does not properly send feedback via RS232. I was never really successful controlling it via IP. |
|
Re: 12V trigger with CP4 Versiport
¿ªÔÆÌåÓýThanks Brian, i think i?ll do it that way. ? Cheers, Thorsten ? Von: [email protected] <[email protected]> Im Auftrag von Brian Matson ? I think that you'd probably be more successful using a step-down from the 24VDC Cresnet through a relay than stepping up a 5VDC Versiport output. |
|
Re: End of Flash/Air?
¿ªÔÆÌåÓýWhich type of panel are you trying to emulate? I¡¯ve had it be very hit or miss (more miss than hit) for odd things like iPads (not surprised ¨C actually a little surprised it worked at all ever) but for normal panels like the TS1542/DGE/TXW-x60 I haven¡¯t had an issue. I think I¡¯m running latest VTP but I¡¯m also in the middle of a major project so not about to update ? ? -- Lincoln King-Cliby, CTS, DMC-E-4K/T/D ? From: [email protected] <[email protected]> On Behalf Of
Tydco
Sent: Wednesday, January 6, 2021 9:48 AM To: [email protected] Subject: Re: [crestron] End of Flash/Air? ? I have the same thing, just updated VT-ProE and now when I click the ¡®Run¡¯ it processes the file but doesn¡¯t run the XPanel emulator. |
|
Re: LG OLED 232
¿ªÔÆÌåÓýCEC should be an option if you¡¯re using something that can generate CEC. ? -- Lincoln King-Cliby, CTS, DMC-E-4K/T/D ? From: [email protected] <[email protected]> On Behalf Of
Ben
Sent: Wednesday, January 6, 2021 9:33 AM To: [email protected] Subject: Re: [crestron] LG OLED 232 ? not OLED but had this issue on some 75ul3e's. would work fine turning on/off when testing, then when left off overnight they would fail to turn back on. ended up being the firmware, which for some reason wouldnt load on site so had to go back to LG get to be done by them. now working fine.? |
|
Re: Samsung CCD IP Driver
Until you have everything working, hook up the driver log output and the user attribute label and description outputs from the module so they can be viewed in SIMPL Debugger.? Those outputs will give you some good tips on what might be wrong and that info doesn't get written to the processor logs.? Until I forced values into the warmup and cooldown times, I had a driver log message indicating the times had to be set to something; the driver wouldn't even attempt to connect to the TV until they were set. Geoff On Wed, Jan 6, 2021 at 11:08 AM rickwookie <rickwookie@...> wrote: Does the power on not work, or does it just not come on for over a minute after you issue the commands? I found I had to nest the warm up and cool down parameters both to 1 second as the default value is really long. |
|
Re: 12V trigger with CP4 Versiport
I think that you'd probably be more successful using a step-down from the 24VDC Cresnet through a relay than stepping up a 5VDC Versiport output.
The Versiport output is a very, very low current output. I've had no problems using a step-down on the Cresnet.? You'll just have to use a relay instead. I always use a diode on the transformer input just to protect the Crestron processor a bit more. |
AVMaster