I have a different TV (LG OLED C8), but these are notes I took when I hooked it up:
? DB9 Pin 3 to 3.5mm Tip
? DB9 Pin 2 to 3.5mm Ring
? DB9 Pin 5 to 3.5mm Sleeve
Also check out:
=> page 24
Maybe you find this helpful.
|
Re: Insteon Lighting Control
I have my CP3 talk to an ISY through REST commands. This allows me to control Insteon devices and scenes. I am also able to get some status feedback via query commands. Not very pretty, but it works sufficiently well in my modest setup.
|
I am having a hell of a time trying to control some insteon lights. I attempted to use the lighting and thermostat module in the files section but it does not seem to compile in a 3 series program.
Is there a better way to control Insteon lights with Crestron. I? have read that some people use the Hub or an ICY but have not seen any modules.?
|
Re: Just posted Insteon lighting & thermostat control modules that I developed
Hello, I have tried this module on a CP3N and it does not compile. There is an error on Line 86 of the module. I am guessing its a bit of cone that is not compatible with a 3 series processor. Has anyone gotten this to work on a 3 Series? Also is there a better way for Crestron to control Insteon Lights thru Crestron? Using a Hub or ICY maybe?
|
Re: Smart Labs Insteon Lighting
Hello, I am interested if anyone has gotten this to work? I have a project with a bunch of Insteon dimmers to control.
|
Hi everyone,
We are installing an LG display ( 86UH5E ) with RS-232 control through the 4-pin TRS connector.
Does anyone know which connections on the display are TX, RX and Ground?
Thanks,
-andy
|
Re: LG Refrigerator Module
Looks like pages 4,5,6 have Refrigerator info!
|
Re: DIN-AP3 D3 Program and C2N Keypads Amuck
We had something similar recently and it all devices would show up fine but I noticed an intermittent flood of update requests from a certain Cresnet ID. We swapped the keypad and our troubles went away. There was another job too where we had odd errors pointing to single ID for a shade. That one ended up being the wire got compromised somehow (finished house maybe something settled and was nicking the wire) but resolving that fixed that site.
Also check to see they havent gone too far over the 20 device limit per Cresnet segment.?
|
Re: KNX, which gateway? CI-KNX or CGEIB-IP?
The biggest difference (except for the group address count) is
that You need a KNX guy every time You need to make a change on
CI-KNX. This unit needs to be programmed on KNX side (ETS
software). If this is not a problem, from my experience, CI-KNX is
not less stable than CGEIB-IP.
On 22. 6. 2020 11:19, Bruce Bartlett
wrote:
toggle quoted message
Show quoted text
I have worked on a number of projects
integrating with KNX using a CGEIB-IP, which seems to work
pretty well. A few years back a Crestron employee suggested to
me that we should always choose the CGEIB-IP in preference to
the CI-KNX, apparently because the CGEIB-IP was a superior and
more reliable product.
???
Opinions please? For those integrating with
KNX, what???s your experience of either of these gateways?
???
Thanks,
???
Bruce
???
???
???
This email and any attachments are intended for receipt and
viewing only by the addressee and may contain confidential
information. If you have received it in error please inform us by
replying to this email, and then delete it from your system. Any
views or opinions expressed in this email are those of the author
and do not necessarily represent those of Sensory International
Ltd. This email and any attachments have been scanned for viruses
upon leaving our system, however we strongly recommend that you
use your own virus protection software and ensure that definitions
are up to date. Sensory International Ltd will accept no
responsibility for any loss of data that may occur from viewing
this email and/or any attachments. Email is not a secure
communications medium and we ask you to consider this when
engaging in correspondence with us. Sensory International operates
within the law and recognizes GDPR. If you feel that our records
need changing please update us by emailing info@...
Company Registration Number: 4461104 Vat Registration No: GB 319
6629 73
______________________________________________________________________
This email has been scanned by the Symantec Email Security.cloud
service.
For more information please visit
______________________________________________________________________
|
KNX, which gateway? CI-KNX or CGEIB-IP?
I have worked on a number of projects integrating with KNX using a CGEIB-IP, which seems to work pretty well. A few years back a Crestron employee suggested to me that we should always choose the CGEIB-IP in preference to the CI-KNX, apparently
because the CGEIB-IP was a superior and more reliable product.
?
Opinions please? For those integrating with KNX, what’s your experience of either of these gateways?
?
Thanks,
?
Bruce
?
?
?
This email and any attachments are intended for receipt and viewing only by the addressee and may contain confidential information. If you have received it in error please inform us by replying to this email, and then delete it from your system. Any views or
opinions expressed in this email are those of the author and do not necessarily represent those of Sensory International Ltd. This email and any attachments have been scanned for viruses upon leaving our system, however we strongly recommend that you use your
own virus protection software and ensure that definitions are up to date. Sensory International Ltd will accept no responsibility for any loss of data that may occur from viewing this email and/or any attachments. Email is not a secure communications medium
and we ask you to consider this when engaging in correspondence with us. Sensory International operates within the law and recognizes GDPR. If you feel that our records need changing please update us by emailing info@... Company Registration Number:
4461104 Vat Registration No: GB 319 6629 73
______________________________________________________________________
This email has been scanned by the Symantec Email Security.cloud service.
For more information please visit http://www.symanteccloud.com
______________________________________________________________________
|
Re: 24VDC power supplies in metro DC?
Ugh…. So close but just not quite
? -- several 12V options and a Lenovo 20V option that I could probably hack a new end onto and would probably work but nothing @ 24V
?
Appreciate the offer but hate to raid your basement stock – I know how valuable having those on hand can be when one hits the “4 years, I’m done” threshold. I’ve bodged something together that isn’t pretty (see: bodge) but working for now
and unless someone else has ?looks like I can Amazon a couple with prime for less than the metro fare – though always great to put faces to names.
?
Lincoln
?
--
Lincoln King-Cliby, CTS, DMC-E-4K/T/D
Commercial Market Director
Sr. Systems Architect | Crestron Certified Master Programmer (Diamond)
ControlWorks Consulting, LLC
Direct: (+1)440.771.4807 | Cleveland: (+1)440.449.1100? | Boston: (+1)508.695.0188 | DC: (+1)202.381.9070? | Fax: (+1)440.449.1106
Crestron Services Provider | Biamp Authorized Independent Programmers | Extron Qualified Independent Programmer
?
toggle quoted message
Show quoted text
From: [email protected] < [email protected]> On Behalf Of
EJ
Sent: Sunday, June 21, 2020 7:14 PM
To: [email protected]
Subject: Re: [crestron] 24VDC power supplies in metro DC?
?
Good luck. If you’re in need I stock a few in my basement for my system, I can give you a couple, but I’m a little further out from Vienna. Arrangements can be always be made so let me know.
EJ
On Jun 21, 2020, at 6:22 PM, Lincoln King-Cliby <lincoln@...> wrote:
?
Hmm… good call. I don’t usually think of Micro Center as a components house but they have gotten much better in recent years (at least the one near our Cleveland office – and I have been to that store when we first moved got her moved out
here and the apartment essentials set up – had a rental car back then. Will check what the website shows for them after dinner.
?
Lincoln
?
--
Lincoln King-Cliby, CTS, DMC-E-4K/T/D
Commercial Market Director
Sr. Systems Architect | Crestron Certified Master Programmer (Diamond)
ControlWorks Consulting, LLC
Direct: (+1)440.771.4807 | Cleveland: (+1)440.449.1100? | Boston: (+1)508.695.0188 | DC: (+1)202.381.9070? | Fax: (+1)440.449.1106
Crestron Services Provider | Biamp Authorized Independent Programmers | Extron Qualified Independent Programmer
?
?
Micro Center off Vienna Metro (Orange Line) might have what you need. Plus I think you can order online for pick up.
EJ
On Jun 21, 2020, at 5:06 PM, Lincoln King-Cliby <lincoln@...> wrote:
?
I’m an idiot – I sent my wife a few boxes to get our apartment in DC up and running but apparently despite throwing a DM-TX-201 and RMC-100-C in the box with a plethora of each of them I apparently spaced on sending a power supply for either
of them.
?
Anyone know of any electronics-type places in the metro area – preferably accessible from the Metro since we’re car-less that I might be able to get before I head back to Cleveland mid-week? I’m in NoMA right off the Red Line but obviously
with the idiot tax being in place…
?
Lincoln
?
--
Lincoln King-Cliby, CTS, DMC-E-4K/T/D
Commercial Market Director
Sr. Systems Architect | Crestron Certified Master Programmer (Diamond)
ControlWorks Consulting, LLC
Direct: (+1)440.771.4807 | Cleveland: (+1)440.449.1100? | Boston: (+1)508.695.0188 | DC: (+1)202.381.9070? | Fax: (+1)440.449.1106
Crestron Services Provider | Biamp Authorized Independent Programmers | Extron Qualified Independent Programmer
?
|
Re: 24VDC power supplies in metro DC?
Good luck. If you’re in need I stock a few in my basement for my system, I can give you a couple, but I’m a little further out from Vienna. Arrangements can be always be made so let me know.
toggle quoted message
Show quoted text
On Jun 21, 2020, at 6:22 PM, Lincoln King-Cliby <lincoln@...> wrote:
?
Hmm… good call. I don’t usually think of Micro Center as a components house but they have gotten much better in recent years (at least the one near our Cleveland office – and I have been to that store when we first moved got her moved out
here and the apartment essentials set up – had a rental car back then. Will check what the website shows for them after dinner.
?
Lincoln
?
--
Lincoln King-Cliby, CTS, DMC-E-4K/T/D
Commercial Market Director
Sr. Systems Architect | Crestron Certified Master Programmer (Diamond)
ControlWorks Consulting, LLC
Direct: (+1)440.771.4807 | Cleveland: (+1)440.449.1100? | Boston: (+1)508.695.0188 | DC: (+1)202.381.9070? | Fax: (+1)440.449.1106
Crestron Services Provider | Biamp Authorized Independent Programmers | Extron Qualified Independent Programmer
?
?
Micro Center off Vienna Metro (Orange Line) might have what you need. Plus I think you can order online for pick up.
EJ
On Jun 21, 2020, at 5:06 PM, Lincoln King-Cliby <lincoln@...> wrote:
?
I’m an idiot – I sent my wife a few boxes to get our apartment in DC up and running but apparently despite throwing a DM-TX-201 and RMC-100-C in the box with a plethora of each of them I apparently spaced on sending a power supply for either
of them.
?
Anyone know of any electronics-type places in the metro area – preferably accessible from the Metro since we’re car-less that I might be able to get before I head back to Cleveland mid-week? I’m in NoMA right off the Red Line but obviously
with the idiot tax being in place…
?
Lincoln
?
--
Lincoln King-Cliby, CTS, DMC-E-4K/T/D
Commercial Market Director
Sr. Systems Architect | Crestron Certified Master Programmer (Diamond)
ControlWorks Consulting, LLC
Direct: (+1)440.771.4807 | Cleveland: (+1)440.449.1100? | Boston: (+1)508.695.0188 | DC: (+1)202.381.9070? | Fax: (+1)440.449.1106
Crestron Services Provider | Biamp Authorized Independent Programmers | Extron Qualified Independent Programmer
?
|
Re: LG Refrigerator Module
After doing some searching it looks like this might be a starting point
though I'm not seeing much for a refrigerator.? I also checked and LG doesn't support a refrigerator through the IFTTT service, only clothes washers and dryers.? That isn't a good sign for finding the functionality you described below that you want.
If you know Python, which I don't, then this might be useful though it looks like it might only support air conditioners.
Hope this helps
Jay
------ Original Message ------
Sent: 6/21/2020 2:54:21 PM
Subject: Re: [crestron] LG Refrigerator Module
It does not ?-- only “Please check the detailed specifications on the notice page on us.smartthinq.com” but that doesn’t really go anywhere.
?
--
Lincoln King-Cliby, CTS, DMC-E-4K/T/D
Commercial Market Director
Sr. Systems Architect | Crestron Certified Master Programmer (Diamond)
ControlWorks Consulting, LLC
Direct: (+1)440.771.4807 | Cleveland: (+1)440.449.1100? | Boston: (+1)508.695.0188 | DC: (+1)202.381.9070? | Fax: (+1)440.449.1106
Crestron Services Provider | Biamp Authorized Independent Programmers | Extron Qualified Independent Programmer
?
?
Does the manual include a link to the API?? I found the LG developer site ()
but that doesn't seem to have content related to controlling an appliances.? I've been writing a lot of drivers lately as part of the articles I've been doing and would be interested in taking a look at this API.
------ Original Message ------
Sent: 6/21/2020 7:22:41 AM
Subject: Re: [crestron] LG Refrigerator Module
That’s where the documentation in the owner’s manual about the API gets a little vague.
?
Biggest thing I think I’ll do is a vacation mode to cut energy consumption because (when the world is operating normally) I travel enough that it would be nice that for that to kick in ‘automatically’ when I put my house enters “long away”
mode* and return to normal when the house is in “normal”.
?
I’m not sure if I’d implement it but you can also tell it you’re going to use more ice than normal which I might tie to activating when the house is in Party Mode
?
It can generate an alarm if the door is open for longer than X minutes which seems like a not awful thing to tie to some other logic
?
Other interesting options that don’t really apply to me but could be useful to people in different situations are control of “Sabbath Mode” (have the Crestron system put the refrigerator into/out of that mode automatically based on calendaring
rather than making the user do it manually) and Smart Grid/Demand Response control where the refrigerator will delay things that require more electricity (making ice, defrosting, etc.) during peek demand times or for areas with TOU/RTP/VPP/CPP ?metering when
costs are the highest… for homes with generators or battery backup, I could also see forcing this mode when utility power isn’t available to reduce/control the load on the emergency power system.
?
*= My house, via the Crestron ecosystem, has essentially four states – Normal (energy usage managed but not to the point of inconvenience), Short Away (slightly more aggressive energy management and some time to “recover” to normal), Long
Away (heavy energy management, significantly longer recovery to normal), or Party (“screw energy management we’re going to have some fun” otherwise known as “don’t scare the guests by allowing too many things to turn on and off automatically” )
?
--
Lincoln King-Cliby, CTS, DMC-E-4K/T/D
Commercial Market Director
Sr. Systems Architect | Crestron Certified Master Programmer (Diamond)
ControlWorks Consulting, LLC
Direct: (+1)440.771.4807 | Cleveland: (+1)440.449.1100? | Boston: (+1)508.695.0188 | DC: (+1)202.381.9070? | Fax: (+1)440.449.1106
Crestron Services Provider | Biamp Authorized Independent Programmers | Extron Qualified Independent Programmer
?
?
Out of curiosity,? what exactly can you do with the api?? Always wondered what the point of it was??
|
Re: 24VDC power supplies in metro DC?
Hmm… good call. I don’t usually think of Micro Center as a components house but they have gotten much better in recent years (at least the one near our Cleveland office – and I have been to that store when we first moved got her moved out
here and the apartment essentials set up – had a rental car back then. Will check what the website shows for them after dinner.
?
Lincoln
?
--
Lincoln King-Cliby, CTS, DMC-E-4K/T/D
Commercial Market Director
Sr. Systems Architect | Crestron Certified Master Programmer (Diamond)
ControlWorks Consulting, LLC
Direct: (+1)440.771.4807 | Cleveland: (+1)440.449.1100? | Boston: (+1)508.695.0188 | DC: (+1)202.381.9070? | Fax: (+1)440.449.1106
Crestron Services Provider | Biamp Authorized Independent Programmers | Extron Qualified Independent Programmer
?
toggle quoted message
Show quoted text
From: [email protected] < [email protected]> On Behalf Of
EJ
Sent: Sunday, June 21, 2020 5:40 PM
To: [email protected]
Subject: Re: [crestron] 24VDC power supplies in metro DC?
?
Micro Center off Vienna Metro (Orange Line) might have what you need. Plus I think you can order online for pick up.
EJ
On Jun 21, 2020, at 5:06 PM, Lincoln King-Cliby <lincoln@...> wrote:
?
I’m an idiot – I sent my wife a few boxes to get our apartment in DC up and running but apparently despite throwing a DM-TX-201 and RMC-100-C in the box with a plethora of each of them I apparently spaced on sending a power supply for either
of them.
?
Anyone know of any electronics-type places in the metro area – preferably accessible from the Metro since we’re car-less that I might be able to get before I head back to Cleveland mid-week? I’m in NoMA right off the Red Line but obviously
with the idiot tax being in place…
?
Lincoln
?
--
Lincoln King-Cliby, CTS, DMC-E-4K/T/D
Commercial Market Director
Sr. Systems Architect | Crestron Certified Master Programmer (Diamond)
ControlWorks Consulting, LLC
Direct: (+1)440.771.4807 | Cleveland: (+1)440.449.1100? | Boston: (+1)508.695.0188 | DC: (+1)202.381.9070? | Fax: (+1)440.449.1106
Crestron Services Provider | Biamp Authorized Independent Programmers | Extron Qualified Independent Programmer
?
|
Re: 24VDC power supplies in metro DC?
Micro Center off Vienna Metro (Orange Line) might have what you need. Plus I think you can order online for pick up.
toggle quoted message
Show quoted text
On Jun 21, 2020, at 5:06 PM, Lincoln King-Cliby <lincoln@...> wrote:
?
I’m an idiot – I sent my wife a few boxes to get our apartment in DC up and running but apparently despite throwing a DM-TX-201 and RMC-100-C in the box with a plethora of each of them I apparently spaced on sending a power supply for either
of them.
?
Anyone know of any electronics-type places in the metro area – preferably accessible from the Metro since we’re car-less that I might be able to get before I head back to Cleveland mid-week? I’m in NoMA right off the Red Line but obviously
with the idiot tax being in place…
?
Lincoln
?
--
Lincoln King-Cliby, CTS, DMC-E-4K/T/D
Commercial Market Director
Sr. Systems Architect | Crestron Certified Master Programmer (Diamond)
ControlWorks Consulting, LLC
Direct: (+1)440.771.4807 | Cleveland: (+1)440.449.1100? | Boston: (+1)508.695.0188 | DC: (+1)202.381.9070? | Fax: (+1)440.449.1106
Crestron Services Provider | Biamp Authorized Independent Programmers | Extron Qualified Independent Programmer
?
|
24VDC power supplies in metro DC?
I’m an idiot – I sent my wife a few boxes to get our apartment in DC up and running but apparently despite throwing a DM-TX-201 and RMC-100-C in the box with a plethora of each of them I apparently spaced on sending a power supply for either
of them.
?
Anyone know of any electronics-type places in the metro area – preferably accessible from the Metro since we’re car-less that I might be able to get before I head back to Cleveland mid-week? I’m in NoMA right off the Red Line but obviously
with the idiot tax being in place…
?
Lincoln
?
--
Lincoln King-Cliby, CTS, DMC-E-4K/T/D
Commercial Market Director
Sr. Systems Architect | Crestron Certified Master Programmer (Diamond)
ControlWorks Consulting, LLC
Direct: (+1)440.771.4807 | Cleveland: (+1)440.449.1100? | Boston: (+1)508.695.0188 | DC: (+1)202.381.9070? | Fax: (+1)440.449.1106
Crestron Services Provider | Biamp Authorized Independent Programmers | Extron Qualified Independent Programmer
?
|
Re: Retrofit wiring Cat5?
How long are the runs?
?
It’s not officially supported because in the old days people did stupid things which wound up underpowering devices and best case causing odd behavior/worst case damaged product. (I can’t remember if its officially as “warranty void if
you do this” or just “please, for the love of your deity/ies, please don’t do this) but horizon keypad power requirements are low enough if each one is home run as a practical matter unless they’re very long runs probably will be ok.
?
Use one pair for data, other pairs for power/ground. Don’t double up the data or split data across multiple pairs. Any runs that can be replaced wt
?
In my house I have a number of Cresnet RJ45s (all Orange for the AV CNET; a couple places also have Yellow for the Lighting CNET) – I used real Cresnet cable to the back of the jack with just a short whip of CAT to punch on the jack and
the pinout I used assuming 568B – for compatibility with the old ST devices with RJ-11s on them – was
?
White/Orange, Orange/White, and White/Green = +24V
Blue/White = Y
White/Blue = Z
Green/White, White/Brown, and Brown/White = GND
?
So looking at the front of the jack you get
?
24 24 24 Y Z G G G
?
This way a ST-something’s RJ-12 can be plugged directly in just ignoring the outside 24+G pins but there’s some extra current carrying capacity for anything I need a custom whip for.
--
Lincoln King-Cliby, CTS, DMC-E-4K/T/D
Commercial Market Director
Sr. Systems Architect | Crestron Certified Master Programmer (Diamond)
ControlWorks Consulting, LLC
Direct: (+1)440.771.4807 | Cleveland: (+1)440.449.1100? | Boston: (+1)508.695.0188 | DC: (+1)202.381.9070? | Fax: (+1)440.449.1106
Crestron Services Provider | Biamp Authorized Independent Programmers | Extron Qualified Independent Programmer
?
toggle quoted message
Show quoted text
From: [email protected] < [email protected]> On Behalf Of
smurfsarecool2002
Sent: Sunday, June 21, 2020 12:25 AM
To: [email protected]
Subject: [crestron] Retrofit wiring Cat5?
?
Hello all,
We always run cresnet on our lighting jobs for keypads but have come across a retrofit that we cannot.? The house has an existing lighting system that used cat5 homeruns.? We are migrating them to Horizon keypads.? Do you forsee any issues using the cat5 in
this instance for keypads only?
Thanks!
Philip
PJW Installations
|
Re: LG Refrigerator Module
It does not ?-- only “Please check the detailed specifications on the notice page on us.smartthinq.com” but that doesn’t really go anywhere.
?
--
Lincoln King-Cliby, CTS, DMC-E-4K/T/D
Commercial Market Director
Sr. Systems Architect | Crestron Certified Master Programmer (Diamond)
ControlWorks Consulting, LLC
Direct: (+1)440.771.4807 | Cleveland: (+1)440.449.1100? | Boston: (+1)508.695.0188 | DC: (+1)202.381.9070? | Fax: (+1)440.449.1106
Crestron Services Provider | Biamp Authorized Independent Programmers | Extron Qualified Independent Programmer
?
toggle quoted message
Show quoted text
From: [email protected] < [email protected]> On Behalf Of
jbasen
Sent: Sunday, June 21, 2020 9:38 AM
To: [email protected]
Subject: Re: [crestron] LG Refrigerator Module
?
Does the manual include a link to the API?? I found the LG developer site ()
but that doesn't seem to have content related to controlling an appliances.? I've been writing a lot of drivers lately as part of the articles I've been doing and would be interested in taking a look at this API.
------ Original Message ------
Sent: 6/21/2020 7:22:41 AM
Subject: Re: [crestron] LG Refrigerator Module
That’s where the documentation in the owner’s manual about the API gets a little vague.
?
Biggest thing I think I’ll do is a vacation mode to cut energy consumption because (when the world is operating normally) I travel enough that it would be nice that for that to kick in ‘automatically’ when I put my house enters “long away”
mode* and return to normal when the house is in “normal”.
?
I’m not sure if I’d implement it but you can also tell it you’re going to use more ice than normal which I might tie to activating when the house is in Party Mode
?
It can generate an alarm if the door is open for longer than X minutes which seems like a not awful thing to tie to some other logic
?
Other interesting options that don’t really apply to me but could be useful to people in different situations are control of “Sabbath Mode” (have the Crestron system put the refrigerator into/out of that mode automatically based on calendaring
rather than making the user do it manually) and Smart Grid/Demand Response control where the refrigerator will delay things that require more electricity (making ice, defrosting, etc.) during peek demand times or for areas with TOU/RTP/VPP/CPP ?metering when
costs are the highest… for homes with generators or battery backup, I could also see forcing this mode when utility power isn’t available to reduce/control the load on the emergency power system.
?
*= My house, via the Crestron ecosystem, has essentially four states – Normal (energy usage managed but not to the point of inconvenience), Short Away (slightly more aggressive energy management and some time to “recover” to normal), Long
Away (heavy energy management, significantly longer recovery to normal), or Party (“screw energy management we’re going to have some fun” otherwise known as “don’t scare the guests by allowing too many things to turn on and off automatically” )
?
--
Lincoln King-Cliby, CTS, DMC-E-4K/T/D
Commercial Market Director
Sr. Systems Architect | Crestron Certified Master Programmer (Diamond)
ControlWorks Consulting, LLC
Direct: (+1)440.771.4807 | Cleveland: (+1)440.449.1100? | Boston: (+1)508.695.0188 | DC: (+1)202.381.9070? | Fax: (+1)440.449.1106
Crestron Services Provider | Biamp Authorized Independent Programmers | Extron Qualified Independent Programmer
?
?
Out of curiosity,? what exactly can you do with the api?? Always wondered what the point of it was??
|
Re: Retrofit wiring Cat5?
I agree with Steve. I would definitely prefer real Cresnet, but in your situation I wouldn't hesitate to use the CAT, esp. with Keypads.
I did a retro project 12+ years ago where I had (10) TPS-6L panels with only (1) cat5e at each. I used Cat-to-Terminal adapters for the connections on both sides and it has worked flawlessly since then. We're in the process of upgrading the system to TSW panels so we'll now convert the CAT back to network connections!!
***? Because Category cables are not intended, with their small solid core conductors, to be stripped, twisted and screwed down upon (maybe this is why some have issues), I HIGHLY recommend RJ45 to Terminal strip adapters.
This is a bit of a pain, but it's definitely much better than re-wiring in some retro projects...
Here's an example of one that I've used:
HTH, Chris K
|
That's all i can say for now as the version i have is definitely not the release version and yes NDA.
|
Bruce Bartlett
Jay