Create an email template (Attribute).

Add a serial tag insert.

Go back to attributes TAB in setup and find the serial join data you want to be included in the email, Select the email rules TAB and find the template you just created. That will then add the serial$ data from the simpl program fusion join (Custom join 50 and above) To the email that fusion sends.

If you are monitoring devices attached to the processor (IPID), I would use the fusion SSI Equipment Status module. Perhaps you have a reason for serial data in the email in which case as above.

Thank you guys,?
the hint from Maksym, regarding the embedded video app?s on/off join, seems to improve the bahviour.
What? I?m testing now: Keep this join off. When flipping to the surveillance page in the project, first send the video URL, wait 2 sec, set the on/off join to on. When switching to another camera, first set the digital join to off again. With a 1s delay, send the new stream ULR, again 1s dealy, digital join to on. When navigating away from the surveillance page, first set the digital join to off again.
One more finding, if the video doesn?t show, black screen, the camera?s OSD still shows an active connection. I haven?t wiresharked the traffic, but I assume the video is streamed, but not processed in the app.
Using the camera?s MJPEG streams and switching to MPEG in the app, doesn?t work at all.

开云体育

Extreme makes a Poe++ switch that will power 24 nvx. It’s not cheap though. I’d go the midspan route

Hi!

Are you sure there is an address book loaded into the Polycom?? Log into it using a web browser and check.? Also, I typically only use either the local or the global, not both, so make sure your smart graphic (I assume you're using a scrolling list) is tied into the right one.?

I've programmed a few systems with Lilin cameras and NVRs, and they always worked great with Crestron. If you want, I can send some URL examples I used, and I may also have a protocol doc from their tech support.

I also posted this on labs and someone there came up with a solution to double encode the embedded url

Thanks

We have used the Microsemi PD-9524GC 24 port midspan injector in the past for remote powering NVX units. I did also find the Planet UPOE-2400G injector but have not used it.

I have an upcoming system that will require a 12x12 ish NVX setup but all endpoints and transmitters (350s or 351s) must be POE on a single switch.? I'm aware that the requirements are POE++ or 802.3b+ type 3.
Does anyone have any strong opinions on this?? Have any experience with a switch that can hang with the POE requirements?? Yes, locally powering them is an option but not in this case.? Thoughts?

for the PKG file.? Extract it to get the 2 files to store on the processor.

and the CCD module is in the Simpl database.? Define the IP and where to look for the files with a SIO and pulse the connect.

I just saw that there are CCD drivers in the Crestron SMW Library; however the version is v1.2 now. It has (10) custom commands with 'Exists' FB and Name Text.
1. Anyone used this successfully?
2. Has anyone found that the Custom commands work for the Favorites?? (It would be nice not to have to use two modules...)

I tell my clients to use the camera app that came with the NVR/DVR. Solves all the problems.?

On Wed, Apr 15, 2020 at 11:47 AM, joshua zimmerman wrote:

FUSION - is a customizable monitoring software Onprem/Cloud (think help desk options, energy management, higher education support desk Etc.)

?

XIO Cloud - is for static monitoring of only provided (embedded types, names, ip address,etc) items are read only.... and only provide minimal configuration types at this time for certain devices, as this is expanding all the time.?

?

thank you??

?

?

--

Joshua B Zimmerman

The beginning of knowledge is the discovery of something we do not understand.
? - Frank Herbert

This message, including any attachments, may include privileged, confidential and/or inside information. Any distribution or use of this communication by anyone other than the intended recipient(s?? The information contained in this e-mail and any attached documents may be privileged, confidential and protected from disclosure. If you are not the intended recipient you may not read, copy, distribute or use this information. If you have received this communication in error, please notify the sender immediately by replying to this message and then delete it from your system.? ? This email may contain confidential and privileged material for the sole use of the intended recipient. Any review or distribution by others is strictly prohibited.? If you are not the intended recipient please contact the sender and delete all copies.

I would say this is too generalized, and XIO cloud isn't just for static info, and certainly isn't minimal from the writeups on it. XIO cloud also allows remote operation in real time of some devices, like a touchpanel, so you can see what the user is doing or take control yourself to get them going as if you were in the room.

I would agree the information can be pretty ambiguous, I had to dig around to find the info below, if you just look at the main XIO info page it's pretty underwhelming. We are in the midst of deciding which way to go, we have the licensing for on-prem Fusion, but last I was aware it could only do basic room control (ie on, off) and would alert you if something went wrong (but you would have to use other software or go to the room to fix it). I lean towards XIO cloud so techs can take control of the room or walk people through what they're doing, but don't care for the licensing as much. There are certainly more features I've glossed over, but this is my general understanding at the moment. Please correct me if I'm wrong, always happy to know more.




XIO Cloud Premium:

Key Features

• Supports a direct device-to-cloud connection via the Microsoft? Azure? software IoT?Hub without requiring any additional hardware
• Remotely provision, monitor, and manage Crestron? devices across an enterprise
• Apply changes to multiple devices at once by organizing them into groups and subgroups
• Update firmware and configure settings for multiple devices simultaneously
• Schedule actions such as program load, firmware updates, and reboots for a future time, including recurrence patterns
• Monitor the status of all connected devices remotely
• Claim hundreds of devices to the cloud before installation
• View real world device usage information using interactive and filterable charts
• Send alert messages to specified users when a device enters an error state
• View error logs in an alert status pane that also displays resolution status
• Track account usage and changes with cloud audit logs
• Integrate status information into other monitoring tools via REST?API interface

The Home/Away/Goodnight are "Tell Crestron" commands, not regular commands. If you want to use Home/Away/Goodnight without saying "Tell Crestron..." you can just create a routine.?

开云体育

开云体育

Yes, the osc is to get a press and hold to keep sending the command for better scrolling.?

Thanks All for the Feedback. A couple more questions:

1. To TRoberts and rpc78? -? I'm not sure that I understand using an OSC for basic control of the NAV commands, could you explain? OR is this just to get a P+H function to automatically keep scrolling with one P+H??

2. To All:? Where are you finding the IP CCD for this?? when I search the CCD drivers webpage, I only com up with IR drivers, no IP, CEC, or other? ?(And why? does there need to be 30+ IR drivers??? ...Sorry, rhetorical question...:) )

TIA

I have customized the emails we get from fusion with our College header.? i have fusion monitoring my IP table to send me an email if something is offline.??

My question is - How do I insert a serial join into the email?? I want the text that is transmitted to a particular Fusion serial join to be inserted into my email template.? ?