¿ªÔÆÌåÓý

ctrl + shift + ? for shortcuts
© 2025 Groups.io
  1. Crestron
  2. Messages
Expanded Topics Messages Polls
Date
Re: Weird Network issues between Crestron products as of late?

 

All Static. Got burned and learned my lesson about avoiding host names years ago.

--- In Crestron@..., "floyd1212" <floyd1212@...> wrote:

Are you using static IPs in your IP Tables, or hostnames?

--- In Crestron@..., "eagrubbs" <eagrubbs@> wrote:

Good one, forgot about that. I have not had to mess with that setting in a while.

There is other info really needed also. What DM firmare. Are you on your own network or the clients? What else is on the network. If it is multiple system with similar problems, do those systems have the some of the same equipment. It could be a device is just killing the network.

Honestly it sounds like a network loop issue since it will work for a bit and then stop/drop offline, do a reboot and work again. That has been my experience with the older firmware DM's where a DM is connected to another DM. I have not had that issue since the 1 IP address firmware.

--- In Crestron@..., trayschaeffer <trayschaeffer@> wrote:

One thing to try, if you have not already, is to turn off auto negotiate in the Ethernet settings.
Doesn't matter much which speed/duplex setting you use but it should be consistent.

Tray


Sent from my Samsung Galaxy Note???, an AT&T LTE smartphonetoritian <toritian@> wrote:
Has anyone else experience weird network connection problems between Crestron equipment with recent updates?

I have had DM Router issues, where it will show the DM Router as being offline until I reboot the DM and then it pops back up online in the IP Table.

This happened in multiple locations with multiple programs/DMs.

On another site I have CP2E running lights talking to another CP2E and I'm having a hell of a time getting them to talk to each other over an EISC.

A reboot of both will usually connect them up for a while, but then they will stop talking.

One processor is showing a status of "UNKNOWN" and the other shows a connection status of "NO_NETWORK", which I don't remember seeing before.

I gave up using Direct Sockets because they seem broke, but this is just basic Crestron 101 falling apart.





[Non-text portions of this message have been removed]
Re: Weird Network issues between Crestron products as of late?

innoventgroup
 

Just FYI, I just finished fighting the same type of issues. All of the sudden I had the same network problems with multiple, non-connected, systems. Come to find out, there were two main issues. First, I had ADMS's at both locations and both were a major contributor to the problem. I could unplug them and the problems went away, plug them back in and the problems would return. Also, another culprit was the 4.007 firmware update. And, finally, the center point of the problem was a Netflix 8 port gigabit switch. I switched it out for a cisco 16 port gigabit switch and all is well. I still get errors on the 4.007 firmware but they are not killing my systems anymore. By the way, you can get rid of the 4.007 errors by rolling back the firmware to the previous version. I hope something in my babbling will help.

Take Care,
DAVE

--- In Crestron@..., "toritian" <toritian@...> wrote:

Has anyone else experience weird network connection problems between Crestron equipment with recent updates?

I have had DM Router issues, where it will show the DM Router as being offline until I reboot the DM and then it pops back up online in the IP Table.

This happened in multiple locations with multiple programs/DMs.

On another site I have CP2E running lights talking to another CP2E and I'm having a hell of a time getting them to talk to each other over an EISC.

A reboot of both will usually connect them up for a while, but then they will stop talking.

One processor is showing a status of "UNKNOWN" and the other shows a connection status of "NO_NETWORK", which I don't remember seeing before.

I gave up using Direct Sockets because they seem broke, but this is just basic Crestron 101 falling apart.
Re: DM System without Processor

 

Most definitely will work. Use this setup for most of the conference rooms
we install.

On Sunday, March 24, 2013, crestronprogrammingfun wrote:

**


Does anyone know if this will work...
A dm wall plate and a dm scaler only. No processor. Set the scaler up for
auto detect to allow vga or hdmi to be plugged in.

Thoughts?

Thanks
Thom



--
Yours truly,

Victor
DM System without Processor

 

Does anyone know if this will work...
A dm wall plate and a dm scaler only. No processor. Set the scaler up for auto detect to allow vga or hdmi to be plugged in.

Thoughts?

Thanks
Thom
Re: symetrix jupiter 8 series

 

Contact me on my personal mail

Marselle001@...
Crestron CAIP
Re: On Site - AV2 not responding

 

The answer availble rg_2-series_control_systems.pdf in the crestron web site page 18/19.

if your problem still exist let me know on my mail :marselle001@...

Rabih Brahim
Crestron CAIP
Re: Going mad... xPanel

 

To Make the web xpanel work please follow the steps below:

After Compile , open xpanel web folder and delete every file has 64 , mainly they are 2 files :

XPanel64
XInit64

then it should work !

Rabih Brahim
Crestron CAIP
Re: ONVIF IP Camera Control command format help

mahek samani
 

hello every one,

below is the model number of the IP camera
Type: PTX
model number is :PBACM - PT300

(3 MEGAPIXEL PTZ DOME CAMERA)



this is the only info i could find . it would be great if some one could help.

Thanks a Zillion.
-Mac



________________________________
From: maheksamani <maheksamani@...>
To: Crestron@...
Sent: Saturday, 23 March 2013 6:08 PM
Subject: [Crestron] Re: ONVIF IP Camera Control command format help

model number is :PBACM - PT300


--- In Crestron@..., "Bryan" <bmorris.gm@...> wrote:

ONVIF is a protocol standard.? It would be more helpful to know what
the
camera type is since we are more likely to have specific modules than
the
generic protocol.

B

From: Crestron@... [mailto:Crestron@...] On
Behalf
Of maheksamani
Sent: Friday, March 22, 2013 1:43 AM
To: Crestron@...
Subject: [Crestron] ONVIF IP Camera Control command format help


Hello All,

I was wondering if someone who had already worked with the PTZ IP
Camera
with ONVIF protocol.

could you please guide me with the how to control the camera from the
touch panel.

I am Able to stream the camera feed with MJPEG. but need to control
the
camera moves.

Thanks a Zillion in advance .

-Mahek







------------------------------------



Check out the Files area for useful modules, documents, and drivers.

A contact list of Crestron dealers and programmers can be found in the Database area.
Yahoo! Groups Links



[Non-text portions of this message have been removed]
Re: URC MX980 wont work with my STRFGWX

 

Good catch, I didn't see/read the "ST" part. Yep, must be the 1-way gateway.

--- In Crestron@..., "Ted" <ted_brincka@...> wrote:

Mark, it will work with the CNRFGWA-418. Ted

--- In Crestron@..., "Mark" <dedicatedsystems@> wrote:

So i bought a URC MX980 and was thinking since the STRFGWX is 418mhz it would work as the receiver.

Am i wrong? I cant drop it in on the symbol... WTH?

and i have another gateway but yep it is a CNRFGWA... that is 418mhz.

so am i screwed?


please understand, i am a commercial guy we do not do allot of handheled remotes..
Re: Weird Network issues between Crestron products as of late?

 

Are you using static IPs in your IP Tables, or hostnames?

--- In Crestron@..., "eagrubbs" <eagrubbs@...> wrote:

Good one, forgot about that. I have not had to mess with that setting in a while.

There is other info really needed also. What DM firmare. Are you on your own network or the clients? What else is on the network. If it is multiple system with similar problems, do those systems have the some of the same equipment. It could be a device is just killing the network.

Honestly it sounds like a network loop issue since it will work for a bit and then stop/drop offline, do a reboot and work again. That has been my experience with the older firmware DM's where a DM is connected to another DM. I have not had that issue since the 1 IP address firmware.

--- In Crestron@..., trayschaeffer <trayschaeffer@> wrote:

One thing to try, if you have not already, is to turn off auto negotiate in the Ethernet settings.
Doesn't matter much which speed/duplex setting you use but it should be consistent.

Tray


Sent from my Samsung Galaxy Note???, an AT&T LTE smartphonetoritian <toritian@> wrote:
Has anyone else experience weird network connection problems between Crestron equipment with recent updates?

I have had DM Router issues, where it will show the DM Router as being offline until I reboot the DM and then it pops back up online in the IP Table.

This happened in multiple locations with multiple programs/DMs.

On another site I have CP2E running lights talking to another CP2E and I'm having a hell of a time getting them to talk to each other over an EISC.

A reboot of both will usually connect them up for a while, but then they will stop talking.

One processor is showing a status of "UNKNOWN" and the other shows a connection status of "NO_NETWORK", which I don't remember seeing before.

I gave up using Direct Sockets because they seem broke, but this is just basic Crestron 101 falling apart.





[Non-text portions of this message have been removed]
Re: DMPS100

 

Have you tried disconnecting the panel from the network and then try to ping that address and the same for the DMPS? Check to see if you have an IP conflict.

--- In Crestron@..., "wes" <wesam_helmy@...> wrote:

i have DMPS100 & TPMC12v screen
the screen disconnected i don't know the reason

DMPS IP: 192.168.1.62. IP TABLE: 172.0.0.1
TP IP: 192.168.1.93. IP TABLE: 192.168.1.62

is this correct configuration?
DGE1 with Keyboard and/or mouse

keithbaldacchino
 

Hi,

Is there any programming required in Simpl Windows, should a keyboard or mouse be connected to the DGE1 with V12 panel?

Also, is the VPG Glass Extender required in Simpl when using the V12 panel in conjuntion with a DGE1?

Thanks
keith
Re: URC MX980 wont work with my STRFGWX

 

Mark, it will work with the CNRFGWA-418. Ted

--- In Crestron@..., "Mark" <dedicatedsystems@...> wrote:

So i bought a URC MX980 and was thinking since the STRFGWX is 418mhz it would work as the receiver.

Am i wrong? I cant drop it in on the symbol... WTH?

and i have another gateway but yep it is a CNRFGWA... that is 418mhz.

so am i screwed?


please understand, i am a commercial guy we do not do allot of handheled remotes..
Re: Weird Network issues between Crestron products as of late?

 

Good one, forgot about that. I have not had to mess with that setting in a while.

There is other info really needed also. What DM firmare. Are you on your own network or the clients? What else is on the network. If it is multiple system with similar problems, do those systems have the some of the same equipment. It could be a device is just killing the network.

Honestly it sounds like a network loop issue since it will work for a bit and then stop/drop offline, do a reboot and work again. That has been my experience with the older firmware DM's where a DM is connected to another DM. I have not had that issue since the 1 IP address firmware.

--- In Crestron@..., trayschaeffer <trayschaeffer@...> wrote:

One thing to try, if you have not already, is to turn off auto negotiate in the Ethernet settings.
Doesn't matter much which speed/duplex setting you use but it should be consistent.

Tray


Sent from my Samsung Galaxy Note???, an AT&T LTE smartphonetoritian <toritian@...> wrote:
Has anyone else experience weird network connection problems between Crestron equipment with recent updates?

I have had DM Router issues, where it will show the DM Router as being offline until I reboot the DM and then it pops back up online in the IP Table.

This happened in multiple locations with multiple programs/DMs.

On another site I have CP2E running lights talking to another CP2E and I'm having a hell of a time getting them to talk to each other over an EISC.

A reboot of both will usually connect them up for a while, but then they will stop talking.

One processor is showing a status of "UNKNOWN" and the other shows a connection status of "NO_NETWORK", which I don't remember seeing before.

I gave up using Direct Sockets because they seem broke, but this is just basic Crestron 101 falling apart.
Re: Weird Network issues between Crestron products as of late?

 

Thanks, but no go.

--- In Crestron@..., trayschaeffer <trayschaeffer@...> wrote:

One thing to try, if you have not already, is to turn off auto negotiate in the Ethernet settings.
Doesn't matter much which speed/duplex setting you use but it should be consistent.

Tray


Sent from my Samsung Galaxy Note???, an AT&T LTE smartphonetoritian <toritian@...> wrote:
Has anyone else experience weird network connection problems between Crestron equipment with recent updates?

I have had DM Router issues, where it will show the DM Router as being offline until I reboot the DM and then it pops back up online in the IP Table.

This happened in multiple locations with multiple programs/DMs.

On another site I have CP2E running lights talking to another CP2E and I'm having a hell of a time getting them to talk to each other over an EISC.

A reboot of both will usually connect them up for a while, but then they will stop talking.

One processor is showing a status of "UNKNOWN" and the other shows a connection status of "NO_NETWORK", which I don't remember seeing before.

I gave up using Direct Sockets because they seem broke, but this is just basic Crestron 101 falling apart.





[Non-text portions of this message have been removed]
Re: Weird Network issues between Crestron products as of late?

 

One thing to try, if you have not already, is to turn off auto negotiate in the Ethernet settings.
Doesn't matter much which speed/duplex setting you use but it should be consistent.

Tray


Sent from my Samsung Galaxy Note?, an AT&T LTE smartphonetoritian <toritian@...> wrote:
Has anyone else experience weird network connection problems between Crestron equipment with recent updates?

I have had DM Router issues, where it will show the DM Router as being offline until I reboot the DM and then it pops back up online in the IP Table.

This happened in multiple locations with multiple programs/DMs.

On another site I have CP2E running lights talking to another CP2E and I'm having a hell of a time getting them to talk to each other over an EISC.

A reboot of both will usually connect them up for a while, but then they will stop talking.

One processor is showing a status of "UNKNOWN" and the other shows a connection status of "NO_NETWORK", which I don't remember seeing before.

I gave up using Direct Sockets because they seem broke, but this is just basic Crestron 101 falling apart.





[Non-text portions of this message have been removed]
Re: TPMC-10 battery

 

Marc,
As a last ditch effort, you might want to try charging the battery WITHOUT turning the panel on. Let it charge over night. Remove the power supply, and power up the panel on battery only. You also may have to pull the battery and reinstall. It may come to life.
Marty

--- In Crestron@..., Marc Nield <nieldm@...> wrote:

Er, no, I just plugged it in and powered it on and the rest is history.

Like I said, the panel now doesn't work even if the battery is out and I just use the power supply, so it seems to have nothing to do with the battery, probably just a coincidence.

If anyone wants the battery, I am happy to send it (from the UK) as my TPMC10 is dead.


On 22 Mar 2013, at 12:40, mm24all <martinp@...> wrote:

Interesting. Did you charge the battery fully first, and then try to power it from battery?

I had 2 batteries refurbed by batteryfill.com with great success, although it took 2-3 charge cycles for the battery life to read correctly in the panel.

Marty

--- In Crestron@..., Marc Nield <nieldm@> wrote:

I used batteryrefill.com for a TPMC10 and it didn't work from the moment I plugged the new battery in (constant reboot loop). Even if I take the battery out and run it only from mains, the same thing happens. It worked perfectly before I sent the battery away. I am not blaming the battery but it's certainly a coincidence.

On 21 Mar 2013, at 12:10, mm24all <martinp@> wrote:

+1 on batteryrefill.com

--- In Crestron@..., "robbie_ray" <rlray@> wrote:

I never could find a replacement but I was able to have new cells put into it.

We used these guys:



--- In Crestron@..., PatM Gmail <pat.molettieri@> wrote:

If you have a Batteries Plus around you they can make 1 for you.

Pat M


From: cheinemann605 <cheinemann@>
Reply-To: <Crestron@...>
Date: Wednesday, March 20, 2013 5:03 PM
To: <Crestron@...>
Subject: [Crestron] TPMC-10 battery

does anybody know where I can get a replacement battery for a TPMC-10?
URC MX980 wont work with my STRFGWX

 

So i bought a URC MX980 and was thinking since the STRFGWX is 418mhz it would work as the receiver.

Am i wrong? I cant drop it in on the symbol... WTH?

and i have another gateway but yep it is a CNRFGWA... that is 418mhz.

so am i screwed?


please understand, i am a commercial guy we do not do allot of handheled remotes..
Weird Network issues between Crestron products as of late?

 

Has anyone else experience weird network connection problems between Crestron equipment with recent updates?

I have had DM Router issues, where it will show the DM Router as being offline until I reboot the DM and then it pops back up online in the IP Table.

This happened in multiple locations with multiple programs/DMs.

On another site I have CP2E running lights talking to another CP2E and I'm having a hell of a time getting them to talk to each other over an EISC.

A reboot of both will usually connect them up for a while, but then they will stop talking.

One processor is showing a status of "UNKNOWN" and the other shows a connection status of "NO_NETWORK", which I don't remember seeing before.

I gave up using Direct Sockets because they seem broke, but this is just basic Crestron 101 falling apart.
Re: Going mad... xPanel

 

Ok, I tried it on a new PC and it shows the new design, but on the PC's which have already run the older design it doesn't update, so I guess this is an IE cache problem rather than Crestron - never seen it before tho!

--- In Crestron@..., "rlf79cm" <rlf79cm@...> wrote:

Tried that, both with the IE options and CCleaner to clear everything - still showing old design :o(

--- In Crestron@..., trayschaeffer <trayschaeffer@> wrote:

Clear the temp files from your browser. That's all I can think of right now...

Tray




Sent from my Samsung Galaxy Note???, an AT&T LTE smartphonerlf79cm <rlf79cm@> wrote:
I've updated my xPanel but whenever I compile and run it through the browser it's showing the old version - I've tried renaming, running it from the PC, processor, etc - always showing the old version. If I compile as an exe the new design works fine, but I can't for the life of me get the browser version to update.

Never seen this before - any ideas?

Cheers, Rick



[Non-text portions of this message have been removed]
80221 - 80240 of 256415