Re: Infinet EX Switch and 1 HP Motor
a switch is a switch
you can control a 120v coil relay who control another bigger relay.
you can control a power plant if you want
just , you need.... neutral ( the white one )
toggle quoted message
Show quoted text
--- In Crestron@..., "jac777888" <jchelton@...> wrote:
Hi,
I am trying to control a pool pump motor and notice the size limit for motors for the CLW-SWEX-P is 1/2 HP and pump is 1HP.
My question is has anyone used or forsee any problems using a CLW-SWEX-P to activate a contactor like a Fuji SC-E1 that has a 120V coil?
Thanks
|
Infinet EX Switch and 1 HP Motor
Hi,
I am trying to control a pool pump motor and notice the size limit for motors for the CLW-SWEX-P is 1/2 HP and pump is 1HP.
My question is has anyone used or forsee any problems using a CLW-SWEX-P to activate a contactor like a Fuji SC-E1 that has a 120V coil?
Thanks
|
Re: Bacnet Comms with Honeywell hawk centraline. S/w coach ax
since march 3 2013 , the priority is managed in Crestron bacnet subsystem
just tried today with latest database AND cp3
and it's working
toggle quoted message
Show quoted text
--- In Crestron@..., "Alessandro Maldini" <alessandro.maldini@...> wrote:
Hi Matt,
beware of the fact that Crestron processor doesn?€?t handle the ?€?priority array?€? of BACnet IP protocol ; when the processor writes a BACnet object, it always does it with ?€?Priority 1?€? (probably highest than that used by the Honeywell control unit).
Alessandro
From: Neil Dorin
Sent: Thursday, December 13, 2012 2:41 PM
To: Crestron@...
Subject: Re: [Crestron] Bacnet Comms with Honeywell hawk centraline. S/w coach ax
BACnet uses UDP communication so there's no need to specify an IP address.
You'll need to have unique IDs assigned for the Crestron processor and the HVAC device you're talking to. It doesn't matter what ID you use as long as they're separate.
Probably the easiest way to handle HVAC control is to use an analog value to send to the HVAC system to request a set point, then the HVAC programmer supplies you with an analog input (input to his system) that will represent the current temp read by his sensor(s).
This way you only need 2 BACnet points per HVAC zone. Add the two for your processor as a device and his HVAC controller you're at 4 points for a single zone, plus 2 points for each additional. Under 50 points can be done with the free license in a 3-series processor.
-Neil Dorin
Sent from my iPhone
On 2012-12-13, at 1:31 AM, "mattstrads" <mailto:matt.stradling%40dawsonsav.co.uk> wrote:
Has anyone got any experience controlling this system over bacnet?
The hvac programmer hasn't done this before and needs to create backet points according to crestron. How can they do this?
Also in the crestron remote bacnet modules there seems to be nowhere to enter the remote IP address, only the name, id and port. Is this all the crestron needs? We did get some feedback about the remote device.
Any tips would be appreciated
Many thanks
Matt
Nessun virus nel messaggio.
Controllato da AVG - www.avg.com
Versione: 2013.0.2805 / Database dei virus: 2634/5953 - Data di rilascio: 12/12/2012
|
Re: symetrix jupiter 8 series
I made 6 or 7 big restaurants ( 350 people ) with that
what do you want to know ?
toggle quoted message
Show quoted text
--- In Crestron@..., "Daniel Fattorini" <dan@...> wrote:
There's a standard one out there (CresDB I think) but be warned: Symetrix stuff is odd. Last time I did one it had a very strange characteristic. It only responded to serial commands via the 232 port if it was connected to a network via the LAN. Pull out the LAN cable and wham: "err\x0D" to all commands. They said its a bug but a damn nasty one if you ask me. Ended up leaving my cheap 4 port switch in the back of it just to keep it working.
--- In Crestron@..., "raid shamsa" <raidshamsa@> wrote:
hi
does any one have a moduel to control a jupitor syries audio switcher from symetrics. will be willing to pay if need be
thanks
|
Re: subpage z-order ft-tps4
Been there, done that... The flip-top simply doesn't have that option. Which tells me that probably a separate team of engineers worked on the flip top model than the 4L. Other than that, I can't imagine why the hardware would be different between the two models.
Weak...
The last triggered subpage is what always shows up. You will have to do some tricks with delayed pulses or something...
Fabio
toggle quoted message
Show quoted text
--- In Crestron@..., "jaaronart" <jaaron7@...> wrote:
Does the flip-top TPS4 not have the option for sub-page z-order? I've always preferred the option for "Follow subpage-reference Z-order" for my projects, so I can always be sure of how the subpages will display. The C2N-FT-TPS4 doesn't have that Compile option, but the TPS4L does.
I can't recall if the option was there before and has disappeared or if I'm just thinking of other touchpanels that I've used.
Can someone confirm if this option was ever available for the ft-tps4?
I just updated everything with Master Installer last night, so I'm wondering if a recent update may have done away with it.
|
Re: symetrix jupiter 8 series
There's a standard one out there (CresDB I think) but be warned: Symetrix stuff is odd. Last time I did one it had a very strange characteristic. It only responded to serial commands via the 232 port if it was connected to a network via the LAN. Pull out the LAN cable and wham: "err\x0D" to all commands. They said its a bug but a damn nasty one if you ask me. Ended up leaving my cheap 4 port switch in the back of it just to keep it working.
toggle quoted message
Show quoted text
--- In Crestron@..., "raid shamsa" <raidshamsa@...> wrote:
hi
does any one have a moduel to control a jupitor syries audio switcher from symetrics. will be willing to pay if need be
thanks
|
Re: Roomview Enabled Display Stupidity
@Jeremy
In fairness to Vivitek, that issue was a Crestron issue, fixed in a SIMPL update (IIRC) about six months ago. It didn't affect just Vivitek, I believe BenQ and others were affected.
And yes, increasing numbers of projectors are turning comms off by default when in standby to meet green star requirements. I had a job recently where we had to jump through hoops to get an Epson to play ball once it was placed in standby (something about Communications On in one of the sub menus...).
Phil.
toggle quoted message
Show quoted text
--- In Crestron@..., Jeremy Weatherford <jweather@...> wrote:
My favorite is the Vivitek projectors that will select any input via the
"RoomView Display" control module except for VGA. Nobody uses that anymore
anyway...
On Thu, Mar 21, 2013 at 3:25 PM, codinsorian <codinsorian@...> wrote:
I particularly enjoy the Epson projectors we purchased that is Roomview
compliant that does not work with....Roomview Enterprise.
Throughly enjoyed that one.
- Dan
--- In Crestron@..., Eric Walters <sentry07@> wrote:
Whyyyyyyyyyyyyyyyyyyyyyy why why why why would a manufacturer put
Roomview
stuff in their projectors and then turn off the web/roomview interface when
you turn off the projector? Unless I'm being extremely stupid here, and not
seeing the option to disable this, I don't get it. Turn the projector on
with the remote and the roomview stuff works, turn the projector off with
roomview and now none of the roomview stuff works and the projector won't
turn on.
WHY?! Tell me I'm not alone on this one, please.
[Non-text portions of this message have been removed]
------------------------------------
Check out the Files area for useful modules, documents, and drivers.
A contact list of Crestron dealers and programmers can be found in the
Database area.
Yahoo!
Groups Links
--
Jeremy Weatherford
|
D3 "link" levels between two switches
Is there any way to make one load's level always match another?
I have a case where a slave switch needs to turn on it's load, as well as an adjacent load. I thought there was a way to say "level1 = level2".
Alternatively, is there a way to somehow respond to the slave button programmatically? I can't see anything, even at the simpl level. Might have to pull this slave out and stick in a keypad or dummy dimmer.
Heath Volmer
Digital Domain Systems
Littleton, CO
|
Does the flip-top TPS4 not have the option for sub-page z-order? I've always preferred the option for "Follow subpage-reference Z-order" for my projects, so I can always be sure of how the subpages will display. The C2N-FT-TPS4 doesn't have that Compile option, but the TPS4L does.
I can't recall if the option was there before and has disappeared or if I'm just thinking of other touchpanels that I've used.
Can someone confirm if this option was ever available for the ft-tps4?
I just updated everything with Master Installer last night, so I'm wondering if a recent update may have done away with it.
|
Re: On site with unfamiliar Denon Receiver
After a quick glance at the API, it appears to be using pretty standard
Denon AVR commands, so I would assume most any modern Denon AVR module would
work. . .at least for core features like power, volume, input, etc.
From: Crestron@... [mailto:Crestron@...] On Behalf
Of Audible Solutions
Sent: Thursday, March 21, 2013 6:35 PM
To: Crestron@...
Subject: [Crestron] On site with unfamiliar Denon Receiver
On Commercial job with a Denon DN-500AV receiver. Not familiar with this
unit and curious if anyone know if any existing module(s), and if so which,
work with this unit?
TIA
Alan
|
On site with unfamiliar Denon Receiver
On Commercial job with a Denon DN-500AV receiver. Not familiar with this unit and curious if anyone know if any existing module(s), and if so which, work with this unit?
TIA
Alan
|
Re: Roomview Enabled Display Stupidity
Yeah, they just use the DB15 connector instead.... :)
toggle quoted message
Show quoted text
--- In Crestron@..., Jeremy Weatherford <jweather@...> wrote:
My favorite is the Vivitek projectors that will select any input via the
"RoomView Display" control module except for VGA. Nobody uses that anymore
anyway...
On Thu, Mar 21, 2013 at 3:25 PM, codinsorian <codinsorian@...> wrote:
I particularly enjoy the Epson projectors we purchased that is Roomview
compliant that does not work with....Roomview Enterprise.
Throughly enjoyed that one.
- Dan
--- In Crestron@..., Eric Walters <sentry07@> wrote:
Whyyyyyyyyyyyyyyyyyyyyyy why why why why would a manufacturer put
Roomview
stuff in their projectors and then turn off the web/roomview interface when
you turn off the projector? Unless I'm being extremely stupid here, and not
seeing the option to disable this, I don't get it. Turn the projector on
with the remote and the roomview stuff works, turn the projector off with
roomview and now none of the roomview stuff works and the projector won't
turn on.
WHY?! Tell me I'm not alone on this one, please.
[Non-text portions of this message have been removed]
------------------------------------
Check out the Files area for useful modules, documents, and drivers.
A contact list of Crestron dealers and programmers can be found in the
Database area.
Yahoo!
Groups Links
--
Jeremy Weatherford
|
Re: Roomview Enabled Display Stupidity
My favorite is the Vivitek projectors that will select any input via the
"RoomView Display" control module except for VGA. Nobody uses that anymore
anyway...
toggle quoted message
Show quoted text
On Thu, Mar 21, 2013 at 3:25 PM, codinsorian <codinsorian@...> wrote: I particularly enjoy the Epson projectors we purchased that is Roomview
compliant that does not work with....Roomview Enterprise.
Throughly enjoyed that one.
- Dan
--- In Crestron@..., Eric Walters <sentry07@...> wrote:
Whyyyyyyyyyyyyyyyyyyyyyy why why why why would a manufacturer put
Roomview
stuff in their projectors and then turn off the web/roomview interface when
you turn off the projector? Unless I'm being extremely stupid here, and not
seeing the option to disable this, I don't get it. Turn the projector on
with the remote and the roomview stuff works, turn the projector off with
roomview and now none of the roomview stuff works and the projector won't
turn on.
WHY?! Tell me I'm not alone on this one, please.
------------------------------------
Check out the Files area for useful modules, documents, and drivers.
A contact list of Crestron dealers and programmers can be found in the
Database area.
Yahoo!
Groups Links
--
Jeremy Weatherford
|
symetrix jupiter 8 series
hi
does any one have a moduel to control a jupitor syries audio switcher from symetrics. will be willing to pay if need be
thanks
|
Re: Roomview Enabled Display Stupidity
There is a setting for Epson projectors to leave comm's enabled when the projector is off. Menu > Extended > Standby Mode > Communications On
toggle quoted message
Show quoted text
--- In Crestron@..., "codinsorian" <codinsorian@...> wrote:
I particularly enjoy the Epson projectors we purchased that is Roomview compliant that does not work with....Roomview Enterprise.
Throughly enjoyed that one.
- Dan
--- In Crestron@..., Eric Walters <sentry07@> wrote:
Whyyyyyyyyyyyyyyyyyyyyyy why why why why would a manufacturer put Roomview
stuff in their projectors and then turn off the web/roomview interface when
you turn off the projector? Unless I'm being extremely stupid here, and not
seeing the option to disable this, I don't get it. Turn the projector on
with the remote and the roomview stuff works, turn the projector off with
roomview and now none of the roomview stuff works and the projector won't
turn on.
WHY?! Tell me I'm not alone on this one, please.
[Non-text portions of this message have been removed]
|
Re: Touchpanel control from
You could just do a init->equ, with a signal for each of the 9 locations, and each output enables a buffer that links your left/right/up/down/select with the appropriate 'next' action.
So loc(1):
left -> goto(3)
right -> goto(2)
up -> goto(7)
down -> goto(4)
select -> trigger(1)
and so on. Its not clever or easily expandable, but is simple and fairly fast to implement at this size, and easy enough to throw into a module to reuse.
toggle quoted message
Show quoted text
--- In Crestron@..., "jrw_96" <jrw_96@...> wrote:
This would be a good way to do and make a hella TT to take care of the logic behind it.
JRW
--- In Crestron@..., Davis Whitehurst <whitehurstd@> wrote:
How about an analog inc for left/right that increments by 1 and analog inc for up/down that increments by 3. Run them into a sum. Add conditional logic for a wrap around effect. Obviously there would be a lot of buffers, ors and nors, but I think it could be done.
If value = 1.
Left sets it 9 for full wrap, or 3 if you just want to horizontal wrap
Right goes to increment
Down goes to increment
Up sets it 9 for full wrap, or 7 if you just want to vertical wrap
If value = 2.
Left goes to inrement
Right goes to increment
Down goes to increment
Up sets it 9 for full wrap, or 8 if you just want to vertical wrap
ETC...
Davis
________________________________
CONFIDENTIALITY NOTICE: This e-mail transmission, and any documents, files or previous e-mail messages attached to it, may contain confidential information that is legally privileged. If you are not the intended recipient, or a person responsible for delivering it to the intended recipient, you are hereby notified that any disclosure, copying, distribution or use of any of the information contained in or attached to this message is STRICTLY PROHIBITED. If you have received this transmission in error, please immediately destroy the original transmission and its attachments without reading them or saving them to disk. Thank you.
[Non-text portions of this message have been removed]
|
Re: Touchpanel control from
That sounds great! A little beyond my Simpl abilities at the moment but I'm going to start trawling through the Help files straight away!
Cheers
toggle quoted message
Show quoted text
--- In Crestron@..., Davis Whitehurst <whitehurstd@...> wrote:
How about an analog inc for left/right that increments by 1 and analog inc for up/down that increments by 3. Run them into a sum. Add conditional logic for a wrap around effect. Obviously there would be a lot of buffers, ors and nors, but I think it could be done.
If value = 1.
Left sets it 9 for full wrap, or 3 if you just want to horizontal wrap
Right goes to increment
Down goes to increment
Up sets it 9 for full wrap, or 7 if you just want to vertical wrap
If value = 2.
Left goes to inrement
Right goes to increment
Down goes to increment
Up sets it 9 for full wrap, or 8 if you just want to vertical wrap
ETC...
Davis
________________________________
CONFIDENTIALITY NOTICE: This e-mail transmission, and any documents, files or previous e-mail messages attached to it, may contain confidential information that is legally privileged. If you are not the intended recipient, or a person responsible for delivering it to the intended recipient, you are hereby notified that any disclosure, copying, distribution or use of any of the information contained in or attached to this message is STRICTLY PROHIBITED. If you have received this transmission in error, please immediately destroy the original transmission and its attachments without reading them or saving them to disk. Thank you.
[Non-text portions of this message have been removed]
|
Re: Touchpanel control from
This would be a good way to do and make a hella TT to take care of the logic behind it.
JRW
toggle quoted message
Show quoted text
--- In Crestron@..., Davis Whitehurst <whitehurstd@...> wrote:
How about an analog inc for left/right that increments by 1 and analog inc for up/down that increments by 3. Run them into a sum. Add conditional logic for a wrap around effect. Obviously there would be a lot of buffers, ors and nors, but I think it could be done.
If value = 1.
Left sets it 9 for full wrap, or 3 if you just want to horizontal wrap
Right goes to increment
Down goes to increment
Up sets it 9 for full wrap, or 7 if you just want to vertical wrap
If value = 2.
Left goes to inrement
Right goes to increment
Down goes to increment
Up sets it 9 for full wrap, or 8 if you just want to vertical wrap
ETC...
Davis
________________________________
CONFIDENTIALITY NOTICE: This e-mail transmission, and any documents, files or previous e-mail messages attached to it, may contain confidential information that is legally privileged. If you are not the intended recipient, or a person responsible for delivering it to the intended recipient, you are hereby notified that any disclosure, copying, distribution or use of any of the information contained in or attached to this message is STRICTLY PROHIBITED. If you have received this transmission in error, please immediately destroy the original transmission and its attachments without reading them or saving them to disk. Thank you.
|
your first ip table is 127.0.0.1 is it a type mismatch ?
have you set the same ip-id on the dmps and the tp ?
{Paf}
2013/3/21 wes <wesam_helmy@...>
toggle quoted message
Show quoted text
**
i have DMPS100 & TPMC12v screen
the screen disconnected i don't know the reason
DMPS IP: 192.168.1.62. IP TABLE: 172.0.0.1
TP IP: 192.168.1.93. IP TABLE: 192.168.1.62
is this correct configuration?
|
Re: Touchpanel control from
How about an analog inc for left/right that increments by 1 and analog inc for up/down that increments by 3. Run them into a sum. Add conditional logic for a wrap around effect. Obviously there would be a lot of buffers, ors and nors, but I think it could be done.
If value = 1.
Left sets it 9 for full wrap, or 3 if you just want to horizontal wrap
Right goes to increment
Down goes to increment
Up sets it 9 for full wrap, or 7 if you just want to vertical wrap
If value = 2.
Left goes to inrement
Right goes to increment
Down goes to increment
Up sets it 9 for full wrap, or 8 if you just want to vertical wrap
ETC...
Davis
________________________________
CONFIDENTIALITY NOTICE: This e-mail transmission, and any documents, files or previous e-mail messages attached to it, may contain confidential information that is legally privileged. If you are not the intended recipient, or a person responsible for delivering it to the intended recipient, you are hereby notified that any disclosure, copying, distribution or use of any of the information contained in or attached to this message is STRICTLY PROHIBITED. If you have received this transmission in error, please immediately destroy the original transmission and its attachments without reading them or saving them to disk. Thank you.
|
fabiodaubermann
Phil Moore
Rapha?l