¿ªÔÆÌåÓý

ctrl + shift + ? for shortcuts
© 2025 Groups.io
  1. Crestron
  2. Messages
Expanded Topics Messages Polls
Date
Re: Samsung ME46A Rant..

cyberbri24
 

Will be working with the ME46A soon. I do not have it in front of me yet. I read all the above posts so far and wanted to see what was working better. The Samsung 400P + 460P (cm), Samsung 2008, or the Samsung CEC mods? I will be using this with a DM-RMC-100. I figure I could use 232 or CEC if possible?

Thanks,
cyberbri

--- In Crestron@..., "flannel_avenger" <rlray@...> wrote:

I did a job with a ME55A a few months ago and I just used the Crestron Module (Samsung 400P + 460P LCD (cm)) and it worked fine for Power On, Power Off, and switching between the analog inputs.

It was a retrofit to an existing system with only analog sources so I didn't try switching to any of the digital inputs.

--- In Crestron@..., "on37j" <janusz.kalaczynski@> wrote:

So here it comes. Much anticipated by me ME46A 46" commercial LED beauty with all bells and whistles, nice footprint, RS232 In and Out, module ready etc. And does not switch inputs, volume commands lock it up in continous flow of feedback. Only PowerOn and Off executed. Firing up a CD manual and here it is on page 43 - "This model does not support BNC, HDMI1, HDMI1_PC, HDMI2, HDMI_2PC and DisplayPort... DVI_video, HDMI_PC and HDMI2_PC cannot be used with the Set command. They only respond to "Get" commands"...
I am scratching my head right now. What have I just brought ? VGA-only device ?
Re: Module for Saving scenes

 

You can build something easily enough using an Analog Variable Preset symbol or the NV Analog to Disk.zip module in the files section here.

--- In Crestron@..., "wes_lim88" <wes_lim88@...> wrote:

Hi guys,

how do you save scenes using touchpanel?

do you guys have a module?

the system uses a din rail lighting system.

it has dimmable and switchable loads.

thanks.
Non-HDCP Compliant Monitor ??

mcjaran
 

A while back someone suggested a device to show HDCP compliant devices on a Non-HDCP compliant monitor.
Any suggestions?
Re: Panel Join Numbers

 

Thank you.

--
Sebastian Marszalek
Re: Panel Join Numbers

 

Hyper terminal or putty work fine

Sent from my iBerry

On Sep 18, 2012, at 11:53 AM, sebastian marszalek <s.marszalek11@...>
wrote:



Thanks Tray,

What application do you recommend to use with a PC?

--
Sebastian Marszalek






[Non-text portions of this message have been removed]
Re: Tandberg C40 Module Help

 

This has proven to be a very frustrating experience trying to get control of this codec. I've turned off the password requirement and still no control. Kinda beaten my head up on the wall with this one. I see communication flowing back and forth but the unit will just not respond to any commands, like it is ignoring them. I know I'm missing something very fundamental as I am working with 2 units and both work the same.

--- In Crestron@..., Lincoln King-Cliby <lincoln@...> wrote:

It can be disabled via TMS or the on-screen menus but by default yes.

--
Lincoln King-Cliby, CTS
Sr. Systems Architect | Crestron Certified Master Programmer (Silver)
ControlWorks Consulting, LLC
V: 440.449.1100 x1107 | F: 440.449.1106 | I:
Crestron Authorized Independent Programmer


-----Original Message-----
From: Crestron@... [mailto:Crestron@...] On Behalf Of techybabble
Sent: Tuesday, September 18, 2012 9:23 AM
To: Crestron@...
Subject: [Crestron] Re: Tandberg C40 Module Help

Does username and password have to be used when going rs232?


--- In Crestron@..., "jcdigitalmethod" <j.j.cunningham@> wrote:

- Check username and password
- Try telnet and see if you have the same issues.
- Try some of the API commands and see if the unit is responding how it should.


--- In Crestron@..., "techybabble" <davelynn@> wrote:

I've happing trouble getting the Crestron module working, the one from the crestron site. It is the Tandberg C90 + C60 Serial v1.3 PRO2 Demo.
According to the Tandberg site is should work with the C40 as well.
I have communication with the box, but even simple things such as IR emulation commands don't respond.

Is there some secret to using these modules. I REALLY need the phonebook directory portion of the module.
All help is appreciated.

thanks



------------------------------------



Check out the Files area for useful modules, documents, and drivers.

A contact list of Crestron dealers and programmers can be found in the Database area.
Yahoo! Groups Links
Re: Christie Solaria Series 4K CP4220 control

Chip
 

Not familiar with that particular unit - what format/syntax do the power commands use?

- Chip

--- In Crestron@..., "shannon.stimpson" <shannon@...> wrote:

I have a beautiful Christie here, not having any luck swithcing inputs.

I am talking to it, power on and off, but formatting the string to select the 'channel' and input are escaping me.

There are four 'channels' programmed to the projector, I am attempting to access channel 12, utilizing the DVI-A input.

Called Christie, not much help. Anyone play with one of these yet?
Christie Solaria Series 4K CP4220 control

 

I have a beautiful Christie here, not having any luck swithcing inputs.

I am talking to it, power on and off, but formatting the string to select the 'channel' and input are escaping me.

There are four 'channels' programmed to the projector, I am attempting to access channel 12, utilizing the DVI-A input.

Called Christie, not much help. Anyone play with one of these yet?
Re: Panel Join Numbers

 

Thanks Tray,

What application do you recommend to use with a PC?

--
Sebastian Marszalek
Re: Panasonic DMP-BDT500 Bluray

Chip
 

I just went through this dance with Panasonic tech support a couple days ago - for this very particular model, no less.

Their (expected?) tier 1 support response: "No - we are not aware of any protocol available for Ethernet control of this device".

That was the second response. The first was "No - we're not aware of any software that will control this device over Ethernet", despite the fact that was *not* the question I asked. :(

So, good luck with that. If you take it on, I hope you can get further than I did.

- Chip

--- In Crestron@..., "solentelectricalservices" <pgrahamsley@...> wrote:

Does anyone have a module, protocol or anything that could help me with a DMP-BDT500 from panasonic, I have the iphone app so I assume the protocol is available, any help would be great thanks
Re: Panel Join Numbers

 

You could receive and capture the serial data into your PC or into another control system like a QM-RMC.
I¡¯d prefer going into another control system but it doesn¡¯t make that much difference.

Tray


From: sebastian marszalek
Sent: Tuesday, September 18, 2012 11:41 AM
To: Crestron@...
Subject: [Crestron] Re: Panel Join Numbers


Works great!

I have another job that I don't even have the source code. Is it possible
to see what is being transmitted on a given Com port?

--
Sebastian Marszalek







[Non-text portions of this message have been removed]
Re: Panel Join Numbers

 

Works great!

I have another job that I don't even have the source code. Is it possible
to see what is being transmitted on a given Com port?

--
Sebastian Marszalek
Panasonic DMP-BDT500 Bluray

 

Does anyone have a module, protocol or anything that could help me with a DMP-BDT500 from panasonic, I have the iphone app so I assume the protocol is available, any help would be great thanks
Re: Refigerators, anyone?

 

Yeah, beer and Dr Pepper count... mmmmm!

I'd like it to scan items going in or out and keep an inventory.

Tray

==

-----Original Message-----
From: Heath Volmer
Sent: Tuesday, September 18, 2012 11:05 AM
To: Crestron@...
Subject: Re: [Crestron] Refigerators, anyone?

I want analog outputs for beer count and Coca Cola count.


On Tue, Sep 18, 2012 at 8:55 AM, Chip <cfm@...> wrote:

**



So the latest I2P module updates include a module for Sub-Zero
refrigerators over RS485.

Nothing wrong with that, but it's still really amusing to me. :)

- Chip







------------------------------------



Check out the Files area for useful modules, documents, and drivers.

A contact list of Crestron dealers and programmers can be found in the Database area.
Yahoo! Groups Links
Re: Refigerators, anyone?

 

I want a picture of the person that opens the refrigerator door. So I
can see who in my house keeps hiding the peanut butter in the fridge.
Everyone knows peanut butter goes in a cabinet.

Real world a contact closure for the door would be nice to send to
touch panels if the fridge was left open and then an email if it's
open for more then 10 minutes. And If the fridge monitored internal
temperatures alarming on temp spike would be nice too, especially for
our clients who have beach houses, if the compressor dies and you
Leave the door closed to the fridge, when you get back in 4 months
your greeted with the most horrific smell ever to start your summer
vacation. It smells so bad you can taste it.



Sent from my iBerry

On Sep 18, 2012, at 11:05 AM, Heath Volmer <hvolmer@...> wrote:

I want analog outputs for beer count and Coca Cola count.


On Tue, Sep 18, 2012 at 8:55 AM, Chip <cfm@...> wrote:

**



So the latest I2P module updates include a module for Sub-Zero
refrigerators over RS485.

Nothing wrong with that, but it's still really amusing to me. :)

- Chip







------------------------------------



Check out the Files area for useful modules, documents, and drivers.

A contact list of Crestron dealers and programmers can be found in the Database area.
Yahoo! Groups Links
Re: Freelance

 

Wellcome!
And by the way, I stay on my own two feet here in Central Europe. Ready to work.

--- In Crestron@..., Bart Podkowka <bart@...> wrote:

Guys,

I am available for freelance work in south of Europe.
Based in Palma de Mallorca.
If someone is interested please contact me off the list


Saludos,
Regards,
mit freundlichen Gr¨¹?en,

Bart J. Podkowka
CISoftware Mallorca

Tel. 971570971 Mov. 616273563
Re: Refigerators, anyone?

Heath Volmer
 

I want analog outputs for beer count and Coca Cola count.

On Tue, Sep 18, 2012 at 8:55 AM, Chip <cfm@...> wrote:

**



So the latest I2P module updates include a module for Sub-Zero
refrigerators over RS485.

Nothing wrong with that, but it's still really amusing to me. :)

- Chip
Refigerators, anyone?

Chip
 

So the latest I2P module updates include a module for Sub-Zero refrigerators over RS485.

Nothing wrong with that, but it's still really amusing to me. :)

- Chip
Dove Lighting Systems

 

Have any of you worked with this system before? I can't seem to find the protocol anywhere. If you guys can point me to where I can find it, that would be great.


Thank you
Parsing Ethernet Data from Onkyo receiver

 

Ive been working on a module for my onkyo tx-nr708 to give me all the ipod info on touchpannels as well as support touching each line to select an option. that all works pretty well as the data comes in pretty small chunks. when i use the same method to parse the network data comming in to use pandora or other streaming services the album art causes everything to go crazy. im not real familiar with any programming language but ive managed to get it to work 100% through serial and am looking for help making work through ethernet. pandora feeds the album artwork out over ethernet not serial and its to much data to fast for my programming to handle. does anyone know how to handle this type of data? if possible id like to even use it to display the same album artwork. this is all being done in simpl+. im just looking for some direction of how to handle and or store this data. thanks in advance.
91381 - 91400 of 256428