¿ªÔÆÌåÓý

ctrl + shift + ? for shortcuts
© 2025 Groups.io
  1. Crestron
  2. Messages
Expanded Topics Messages Polls
Date
Re: CLS-C6 how to

 

You can change the load type from switching to dimming on the units themselves. The steps are all laid out in the reference guide, page 7 onward

.
CLS-C6 how to

 

I inherited a project with 4 of these devices.? On two of the devices none of the zones dim (they act like a switch: ON or OFF).? It appears that the setup for this is handled thru iLux Designer software.? Is there another way to access the unit setup??

If not, I cannot find the pin out for the 1/4" jack.? Does anyone have this and a known good USB-serial adaptor to get into these units?
Re: CRESTRON CONSTRUCT first impressions

 

Causes a JAVA script error at first run, hit OK, then splash screen shows up, which needs to be ended via task manager.

Too busy to figure it out right now (maybe reinstall or Java update?) -? something on my list to look at next week.
Re: Netatmo integration

 

¿ªÔÆÌåÓý

I looked at writing a Netatmo integration driver a few years ago.? They use full OAUTH2 authentication protocol which makes integration with a Crestron processor problematic.? If you are looking for a weather station to integrate with I would highly recommend the WeatherFlow Tempest.? Very well designed weather station and I have just made some significant updates to the free driver on my GitHub.?

Hope this helps

Jay

On 6/12/2023 11:03 AM, Thorsten K?hler wrote:

Hi,

?

anyone already doing integration of the Netatmo system into Crestron?

?

Thanks,

Thorsten
Netatmo integration

 

¿ªÔÆÌåÓý

Hi,

?

anyone already doing integration of the Netatmo system into Crestron?

?

Thanks,

Thorsten
CRESTRON CONSTRUCT first impressions

 

If anyone have feedback please share! Curious to see if it's working well.
Re: DM8x8 - all 5 room boxes have problems?

 

Mark,
I can't remember, did you try locally powering the RMCs?
Re: CCD Samsung QLED can't connect

 

Am I just old, or was the original way of using modules in SMW much simpler??
Re: DM8x8 - all 5 room boxes have problems?

 

client ran new cat cable to PJ, still not working
asked client to source another POE switch
i can't think of what else could be causing things to be intermittent
all boxes worked locally on short cables & my POE injector
Re: CCD Samsung QLED can't connect

 

got the full model #, picked the correct Samsung CCD driver
dealer wired the set, works now
Re: CCD Samsung QLED can't connect

 

Yeah, there probably are. I updated the repo to have a full package download option, notably it includes a couple of DLLs that it needs. . If that still doesn't work (or if anyone else has any issues), feel free to shoot me an email or a message on GitHub and I'll look into it further.
Re: Event Scheduler 2 v1.2.0 issues

 

Nevermind, gave up and coded a custom one.....
CP3N Image

 

Hi,

I have a CP3N with a defective SD card. Could someone help me with an image file. The MAC and SN will be changed directly.

-Sascha
Re: NAX with NVX AES67 stream issues

 

We've had lots of issues too. I'm not quite ready to call it the secret sauce, but it does seem manually setting the NAX port on all NVX devices to 5004 and sending 5004 with every stream switch has made a difference.?

Jonathan
Re: CCD Samsung QLED can't connect

 

Sound like a nice tool.

Can't seem to get CCDInfo.exe to do anything though - neither from Explorer nor the command line. No messages, just does nothing. Are there some dependancies I'd need?
Re: CCD Samsung QLED can't connect

 

I made a small GUI program that parses the information from a CCD and makes it easier to read. It takes either the zip file or the pkg file and shows the most useful pieces of information in a table view instead of just a JSON file. It also displays the JSON, if you wanted to see the rest of the data without going through all the unzipping stuff. For anyone who is interested, it's on GitHub at (there's a "release" just so there's a downloadable executable if you don't want to compile the project).
Re: NAX with NVX AES67 stream issues

 

I've had these problems in the past.? There are always one of two problems, network configuration and streaming port settings.

If you check the "Device is Master PTP Clock Source" and all NAX say yes, then it is a network issue.?

For the port issue, I have manually set the NAX port on all NVX devices to port 5004.? The NAX doesn't like changing ports for some reason.? I have witnessed all zones on a single NAX stop working when any zone changes streams with a different port.? The only way to get audio working again is to clear all stream (enter 0.0.0.0 in stream address) then resend the address.? After manually matching all port values, the problem goes away.

Jay
NAX with NVX AES67 stream issues

 

Am I the only one having loads of trouble (Rx streams stuck on "Connecting") lately? Weh ave lots of NAX jobs where we only have audio from NAX 1 or 2 or even 3, but now we are starting to use the AES67 stream output of NVX cards and having loads of problems.

Crestron Support has come back with loads of things to try that don't help:
-re-send the Port[5004] every time you switch streams
-Stop, change stream, then start stream
-change port 4570 for Video sources and 5004 for Audio sources
-update all your firmware
-use our Crestron (Netgear 4250 switch)
-etc, etc

These amps just seem to get stuck and rebooting amp/s might get things working for a few hours or days. but it stops again. Switching from NAX stream to NAX stream will be fine, but then you switch a NVX AES67 stream and things either stick on connecting or you might get sound, but then when you go back to NAX audio you have no sound. its variable and frustrating.

Anyone found the secret sauce and care to share? Anyone else doing this with Simpl and having success?

Jon
Re: CCD Samsung QLED can't connect

 

¿ªÔÆÌåÓý

Use 7zip to open the archive and open the day in notepad++. Look for the user attributes and follow them. Alternatively you can set the program to load the driver and send the user attributes to serial joins and send them to a msp. Then in toolbox read the strings.

It will tell you per display what needs to be done to connect.

Cheers

Natalie

On Jun 7, 2023, at 4:25 PM, Steve Adams <steveadams172@...> wrote:

?
I believe you have to go into the settings menu and allow 3rd party control to get the pop-up.

On Wed, Jun 7, 2023, 11:53 AM Natalie Jackman <natalie.noel.jackman@...> wrote:
The protocol is backwards compatible. There might be new things but the old tends to still work. The inputs might not align. Find the driver that has the same set of inputs.

Also keep in mind that the display uses wol for power. Grab the MAC address for the Ethernet port not the wireless amax address and provide that to the correct user attribute string value following the documented format.

Cheers

Natalie

On Jun 7, 2023, at 9:20 AM, mark kaye <markkaye@...> wrote:

?i have asked to have it hardwired
i also notice that he QN90 is not on the list in the CCD driver file
i hope it isn't different than all the other QLEDs
the popup has never appeared

Re: CCD Samsung QLED can't connect

 

I believe you have to go into the settings menu and allow 3rd party control to get the pop-up.


On Wed, Jun 7, 2023, 11:53 AM Natalie Jackman <natalie.noel.jackman@...> wrote:
The protocol is backwards compatible. There might be new things but the old tends to still work. The inputs might not align. Find the driver that has the same set of inputs.

Also keep in mind that the display uses wol for power. Grab the MAC address for the Ethernet port not the wireless amax address and provide that to the correct user attribute string value following the documented format.

Cheers

Natalie

On Jun 7, 2023, at 9:20 AM, mark kaye <markkaye@...> wrote:

?i have asked to have it hardwired
i also notice that he QN90 is not on the list in the CCD driver file
i hope it isn't different than all the other QLEDs
the popup has never appeared

6541 - 6560 of 256458