开云体育

There's some videos in OLH: 2015
What's your level of experience with HTML/CSS/JS?

You could try the CH5 xpanel, mentioned on another thread here, the github project link -?

There are a few resources listed here -?

Most people I know are staying away from the CH5 components and are just using the crcomlib or going with a websocket, totally away from Crestron's solution

thought it may have been, posted here as well (in case people were searching for an answer)

Has anyone been successful in tying a CEN-TRACK-AMFMSRD to a Crestron Home system.? I can pair it but it only comes in as the CEN-TRACK.? Any suggestions?

On Tue, Feb 22, 2022 at 02:52 AM, <alex@...> wrote:

The only issue I remember having is the mute toggle would occasionally not work (on an older unit, SR5007). This was due to the feedback not updating, therefore kept sending mute off instead of swapping between on and off in the module. Sending the mute via the IR remote seemed to fix it and get it to work again but a bit of an odd one.?

Yeah I found that a long time ago with the Denon units, had to go into the module and adjust the timing and also poll the unit when turning it off - We saw that if the unit was Muted when turned off, then when it turned back on, the module assumed that it was opposite what it was...

My Application is using a Pro3 with the TSRs.?
Since we Changed the APs from uBiquiti to Araknis (Though I agree that it is likely nothing to do with the Ubiquiti units) and set up dedicated SSIDs for each remote,? we have not seen the hanging SubPage issue for the last 5-6 months...

One thing we've also seen is that though we have a Dedicated SSID on each AP and lock individual TSRs to one AP/SSID, sometimes when the network is rebooted, the TSRs will connect to another SSID. in particular it would connect to the 'xFinity' SSID ...Yes, we had turned it off, but you know that tech knows better so it would occasionally turn back on...
This is particularly annoying as we have, multiple times, told the TSRs to forget this SSID, but it will still do it sometimes...:(:(:(

We can only wish that would be possible :o)

Yes I have seen the opposite were sub pages don't show up even though they are asserted.? In my case, it was caused by too much multicast traffic on the network overwhelming the TSR-310.? Enabling IGMP snooping on the switches and APs solved the issue for me.? I would imagine that broadcast storms or just too much network broadcast traffic could cause similar issues.? But in my case, WireShark showed that it multicast chatter rather then broadcast traffic that was causing the issue. I would also consider putting the TSR-310's on there own SSID and subnet to isolate them from the rest of the network for installations that have lots of network devices.

I went through this last year, there's notes on crestron's website look up xpanel conversion tool

It's a TSR and 2 series issue. I had exactly the same issue on a project. I tried various firmware issues with no luck and ended up replacing with a 3 series.?

Nope. And you can't downgrade a CP4 to a CP4R either.

Anyone out there having/had anything similar? Tough one as we don't do the network there, it is half the country away, and no remote access... Digitals are latching high on the TSR, even though debugger shows digital signal has gone back to low... all other interfaces work fine/show proper feedback. Just the 310's hanging up on old data... I have a feeling it is the network, or some odd TSR / 2 series firmware issue.?

I have a new GUI theme with me. It has separate html code file for every page design. I would like create the theme using CH5 and upload to touchpane/xpanel. Do i need to install crestron contract editor or crestron cli through vscode would suffice? A brief step by step walkthrough would be of great help.

Hi, I have a CP4R processor but need a non-home processor. Is it possible to reconfigure/reflash the CP4R I have to be a standard CP4?

Hi, I have a CP4R processor but need a non-home processor. Is it possible to reconfigure/reflash the CP4R I have to be a standard CP4?

The only issue I remember having is the mute toggle would occasionally not work (on an older unit, SR5007). This was due to the feedback not updating, therefore kept sending mute off instead of swapping between on and off in the module. Sending the mute via the IR remote seemed to fix it and get it to work again but a bit of an odd one.?

Setting the "userpageauth" to ON via text console worked for me.

Im the same guy who posted on reddit. Its working.

Anyone know how to see a touchpanel's console.log ?
other than the console command err sys?