Null Folder - Network Device Tree View
Does anyone know why I am getting a Null folder on my network device tree view? Cresnet devices are reporting fine, but non of the ethernet devices are reporting. However, the processor is connected to all devices and everything is working as usual. This is happening to all my RMC3s.
|
sonos line in Module V1.0
couple of questions- - does this work with Sonos 9.0 firmware?
- if the zone is in a group will it pull out of the group?
- What is the MAC address format?
TIA Chap Cory
|
Issues to use the HEOS DENON module
Hellow every one I downloaded the Heos Denon module because I want to integrate a Heos Likn and Heos Amp for a client but I'm not sure if the module that is in the crestron market works, I tried to import the module in simple windows but it says that the version is not compatible so I would like to know if some one has used it? Also I read that the module has some issues?
|
Re: NVX on Control Subnet
This probably doesn't answer your question, but just in case anyone is wondering, the DM-NVX-350/1 does not support VLANs, tagging, and etc.? I myself was hoping to use the built in LAN port on a pair of DM-NVX-351s connected by a fiber link to get Ethernet to the remote end.? But when I had to use VLANs at the remote site for other reasons, I had to run a dedicated Ethernet run.
|
Re: NVX on Control Subnet
Well I tried to get version number off of switch, but power was off at the jobsite all day.? I will try again next week (I'll be back there on Monday).? I did have a brief chance to look at the subscription list in 1 NVX unit before the power was cut off, and my subscription list was not populated.? I did not set an IP address on the switch as jcallaghan0176 mentioned and that could be the issues for that.? Also if you are going to control with SIMPL program than you'll need to set an IPID (I did this with Powershell).
|
Re: NVX on Control Subnet
You will want to set an IP on the switch as it needs a valid IP address for the querier to work properly. Other than that the IGMP is already available.
|
Just a shot in the dark, but does anyone have a module to control a JVC KY-PZ100 IP Camera?? I could really use some help controlling this one as I'm a little daunted by the API that I've found online.
TIA for your help
Chris Cates
|
Re: Cisco Green "Join" Button
Anyone know for sure if this module works for audio only calls?
|
What Slip and Phil said: +1
?
Caleb Radecky |
Manager, Online Products & Services
Crestron Silver Certified Programmer | DMC-D-4K | DMC-E-4K
ControlWorks Consulting, LLC |
Crestron Services Provider
| 701 Beta Dr. #22 Cleveland OH 44143
D. 440.771.4809 | O.440.449.1100 X1109 | F.440.449.1106 |
?
toggle quoted message
Show quoted text
From: Crestron@... [mailto:Crestron@...]
Sent: Thursday, July 26, 2018 11:19
To: Crestron@...
Subject: [Crestron] Re: Lots of buttons
?
?
|
Haven't had any experience with the Color Kinetics iPlayer3.? The OFF command in the serial driver actually works as a toggle power command.? The module in the Application Market is the one I am using and hasn't been updated in 10 years.? Was looking to see if there is actually a discrete off command that anyone is aware of or what have people done as a work around? I was thinking of learning my way through the Color Player software to see if I could create a BLACK show, all colors at 0.? Just thought I would ask here before going down the rabbit hole for a single project.
Also, for anyone that is familiar with this software.? Is it possible to upload the running program from the iPlayer3, so that programming can be done off site?
|
|
|
What I would do in this case is have 1 subpage for the mic button, apply it multiple times to the page, and use subpage offsets to differentiate each position.
?
Having
an issue with a project loaded to a DM-DGE-200-C. Customer is expecting
an aerial view map of a 400 seat auditorium, each seating having a
microphone, with an indicator for the mic state at each seat.
Have this programmed but the subpage with
400+ advanced buttons on it is a bear to work with in VTPro and when we
load it to the DGE-200 it will cause the project to freeze and reload.
Device does not reboot, just reloads the project. Tried on a DGE-100 as
well with the same results.
Anyone know if these is a limit to the number of buttons a single subpage should have
with SmartGraphics? Anyone create something similar before
and have a way to help manage resources to make this functional?
I seem to remember some recommendation about making everything a page in
SG and only shared resources a subpage? In the iSys days we usually
made a single page for the project and everything was a subpage, seem to remember this is not the recommended method with SG.
Any help is greatly appreciated.
|
Having
an issue with a project loaded to a DM-DGE-200-C. Customer is expecting
an aerial view map of a 400 seat auditorium, each seating having a
microphone, with an indicator for the mic state at each seat.
Have this programmed but the subpage with
400+ advanced buttons on it is a bear to work with in VTPro and when we
load it to the DGE-200 it will cause the project to freeze and reload.
Device does not reboot, just reloads the project. Tried on a DGE-100 as
well with the same results.
Anyone know if these is a limit to the number of buttons a single subpage should have
with SmartGraphics? Anyone create something similar before
and have a way to help manage resources to make this functional?
I seem to remember some recommendation about making everything a page in
SG and only shared resources a subpage? In the iSys days we usually
made a single page for the project and everything was a subpage, seem to remember this is not the recommended method with SG.
Any help is greatly appreciated.
|
Re: NVX on Control Subnet
Oh - that's pretty cool. Thank you.
|
update crestron softwares, especially vt-proe which will help you to know whether crestron app is rendered with iPhone X
also, install crestron app in iPhone X, under settings you can find screen width & height resolution
On Thursday, 26 July, 2018, 11:57:12 AM IST, rajivjain74@... [Crestron] wrote:
?
Is Crestron App rendered full screen on the iPhone X as yet. If yes, what's the resolution we should work on.
Thanks is advance
RJ
|
Re: Crestron AV2 - Power supply defect
Thank you so much Mr.Istvan, we have replaced the power supply as you have suggested.. its perfectly fine..
On Friday, 15 June, 2018, 6:57:54 PM IST, kosik77@... [Crestron] wrote:
?
Mean Well PS-65-24? ?power supply
It's perfect fit.
±õ²õ³Ù±¹¨¢²Ô ---In Crestron@..., wrote : Hi, Crestron AV2 has a power supply defective. If somebody can let me know its voltage & power rating, it would greater help to fix. Thanks.
|
Re: LG Commercial display control via SNMP
Hi Phil, I never controlled an LG via SNMP, please upload the protocol to the files section so,we can have a look at it. Recently I had a SNMP controlled power distributor, this was my first experience with SNMP. You need the MIBs and the SNMP modules. I downloaded an example from the Application market for a RANE DSP, which is controlled via SNMP. It contains nice SNMP modules, which You can use. The MIBs should be documented in the protocol from LG, as an alternative you can find out them witha MIB Browser of your choice.
Best regards Crestronfreak55
|
LG Commercial display control via SNMP
Has anybody controlled an LG commercial display via SNMP?
I have a protocol document and a port # but it does not give an example of exactly what to send and I'm on a tight schedule and I don't have the display with me.
Cheers Phil
|
Is Crestron App rendered full screen on the iPhone X as yet. If yes, what's the resolution we should work on.
Thanks is advance
RJ
|
Re: CEN-NSP1 Player dropping from the network
I have several at clients homes that drop offline all the time. ?I have to power cycle the POE and they show up again. ?I always use Araknis network systems and they suggested that something else on the network like a DirecTV DVR could be set as the master on a network switch priority list. ?I think we were able to resolve it at one location, but now that the NSP is discontinued, I've given up. ?If anyone complains I'll sell them a MMS1.
|
Justin Hill
Phil Moore