|
I found that the 7300 needs a little more commands to control the mode like USB-D
can someone explain the different options available. ?like P123, R1.. I assume R1 is for the radio number but I have to find a document that goes into more detail then the info below
Supported Radios:
Kenwood TS590S/SG ICOM IC7100 ICOM IC7200 ICOM IC7300 ICOM IC7410 ICOM IC7600 Yaesu FT991/991A
If you are running a Sound Card Modem using the internal soundcard and PACTOR (or other TNC Modes) using the AUX connector the input to the modulator has to be changed depending on which is transmitting. As the Soundcard TNC sends PTT ON and PTT OFF commands to the application, these can be used to switch the input source. To enable this add PTT_SETS_INPUT to the RIGCONTROL config, eg
RIGCONTROL COM8 19200 ICOM IC7100 88 PTT_SETS_INPUT ?6,14.110,usb,F1,d,P123,R1 ?6,28.110,usb,F1,d,P123,R1 ****
THanks in advance
Robert Cartier
kd1jg@...
|
P123 is Pactor 1, 2, or 3
P23 is Pactor 2 & 3 only.
P34 is Pactor 3 and 4 only.
R1 is Robust Packet 300
R2 is Robust 600
vn is Vara 500hz
vw is Vara 2300
vt is Vara 2750
?
Lots more at
?
?
--
73,
Mark, N5MDT
Montgomery, Texas
?
?
?
|
This only applies if you are running a sound card modem and a
hardware TNC on the same radio. If you only use VARA or other sound
card modes you just set Data mode modulation source to USB and leave
it there.
PTT_SETS_INPUT is used to switch modulation source between AUX and
USB if you have a Pactor TNC attached to the AUX port.
73, John
On 27/02/2025 18:29, Robert Cartier via
groups.io wrote:
toggle quoted message
Show quoted text
I found that the 7300
needs a little more commands to control the mode like USB-D
can someone explain the different
options available. ?like P123, R1.. I assume R1 is for the
radio number
but I have to find a document that
goes into more detail then the info below
Supported Radios:
Kenwood TS590S/SG
ICOM IC7100
ICOM IC7200
ICOM IC7300
ICOM IC7410
ICOM IC7600
Yaesu FT991/991A
If you are running a Sound Card Modem using the internal
soundcard and PACTOR (or other TNC Modes) using the AUX
connector the input to the modulator has to be changed
depending on which is transmitting. As the Soundcard TNC
sends PTT ON and PTT OFF commands to the application, these
can be used to switch the input source. To enable this add
PTT_SETS_INPUT to the RIGCONTROL config, eg
RIGCONTROL COM8 19200 ICOM IC7100 88 PTT_SETS_INPUT
?6,14.110,usb,F1,d,P123,R1
?6,28.110,usb,F1,d,P123,R1
****
|
thanks but without the PTT_SETS_INPUT my radio stays in USB and not USB-D and I get no signal to the internal card of the 7300
I found that I need the following to get my setup to work
Also since I am not currently scanning is their a way to set the frequency and not have it poll the radio I see when I set it to 5 you can see the mode switch every 5 seconds between usb and USB-D
Thanks
PORT ?PORTNUM=2 ?ID=HF VARA ?DRIVER=VARA ?INTERLOCK=1 ?PORTCALL=NNA1AH-10 ?CONFIG ?ADDR 127.0.0.1 8300 PTT CI-V PATH C:\VARA\VARA.exe ?APPL BBS ?BW2300 RIGCONTROL ?COM4 19200 ICOM 7300 94 PTT_SETS_INPUT ?99,4.9130,USB,D,F1 ?;5,7.3825,USB,D,F1 ? ?**** ENDPORT
On Feb 27, 2025, at 15:21, John G8BPQ via groups.io <john.wiseman@...> wrote:
This only applies if you are running a sound card modem and a hardware TNC on the same radio. If you only use VARA or other sound card modes you just set Data mode modulation source to USB and leave it there. PTT_SETS_INPUT is used to switch modulation source between AUX and USB if you have a Pactor TNC attached to the AUX port. 73, John On 27/02/2025 18:29, Robert Cartier via groups.io wrote:
I found that the 7300 needs a little more commands to control the mode like USB-D
can someone explain the different options available. ?like P123, R1.. I assume R1 is for the radio number but I have to find a document that goes into more detail then the info below
Supported Radios:
Kenwood TS590S/SG ICOM IC7100 ICOM IC7200 ICOM IC7300 ICOM IC7410 ICOM IC7600 Yaesu FT991/991A
If you are running a Sound Card Modem using the internal soundcard and PACTOR (or other TNC Modes) using the AUX connector the input to the modulator has to be changed depending on which is transmitting. As the Soundcard TNC sends PTT ON and PTT OFF commands to the application, these can be used to switch the input source. To enable this add PTT_SETS_INPUT to the RIGCONTROL config, eg
RIGCONTROL COM8 19200 ICOM IC7100 88 PTT_SETS_INPUT ?6,14.110,usb,F1,d,P123,R1 ?6,28.110,usb,F1,d,P123,R1 ****
|
Thanks On Feb 27, 2025, at 14:10, Mark Taylor via groups.io <mtaylor@...> wrote:
P123 is Pactor 1, 2, or 3
P23 is Pactor 2 & 3 only.
P34 is Pactor 3 and 4 only.
R1 is Robust Packet 300
R2 is Robust 600
vn is Vara 500hz
vw is Vara 2300
vt is Vara 2750
?
Lots more at
?
?
--
73,
Mark, N5MDT
Montgomery, Texas
?
?
?
|
You can send RADIO commands from the node or a BBS forwarding
script.
Can't you just leave the radio in USB-D?
73, John
On 27/02/2025 21:35, Robert Cartier via
groups.io wrote:
toggle quoted message
Show quoted text
thanks but without the
PTT_SETS_INPUT my radio stays in USB and not USB-D and I get no
signal to the internal card of the 7300
I found that I need the
following to get my setup to work
Also since I am not
currently scanning is their a way to set the frequency and not
have it poll the radio
I see when I set it to 5
you can see the mode switch every 5 seconds between usb and
USB-D
Thanks
PORT
?PORTNUM=2
?ID=HF VARA
?DRIVER=VARA
?INTERLOCK=1
?PORTCALL=NNA1AH-10
?CONFIG
?ADDR 127.0.0.1 8300 PTT CI-V PATH C:\VARA\VARA.exe
?APPL BBS
?BW2300
RIGCONTROL
?COM4 19200 ICOM 7300 94 PTT_SETS_INPUT
?99,4.9130,USB,D,F1
?;5,7.3825,USB,D,F1
?
?****
ENDPORT
This only applies if you are running a sound
card modem and a hardware TNC on the same radio.
If you only use VARA or other sound card modes
you just set Data mode modulation source to USB
and leave it there.
PTT_SETS_INPUT is used to switch modulation
source between AUX and USB if you have a Pactor
TNC attached to the AUX port.
73, John
On 27/02/2025
18:29, Robert Cartier via groups.io wrote:
I found
that the 7300 needs a little more commands
to control the mode like USB-D
can someone
explain the different options available.
?like P123, R1.. I assume R1 is for the
radio number
but I have to
find a document that goes into more detail
then the info below
Supported Radios:
Kenwood TS590S/SG
ICOM IC7100
ICOM IC7200
ICOM IC7300
ICOM IC7410
ICOM IC7600
Yaesu FT991/991A
If you are running a Sound Card Modem
using the internal soundcard and PACTOR
(or other TNC Modes) using the AUX
connector the input to the modulator has
to be changed depending on which is
transmitting. As the Soundcard TNC sends
PTT ON and PTT OFF commands to the
application, these can be used to switch
the input source. To enable this add
PTT_SETS_INPUT to the RIGCONTROL config,
eg
RIGCONTROL COM8 19200 ICOM IC7100 88
PTT_SETS_INPUT
?6,14.110,usb,F1,d,P123,R1
?6,28.110,usb,F1,d,P123,R1
****
|
On Thu, Feb 27, 2025 at 03:35 PM, Robert Cartier wrote:
I see when I set it to 5 you can see the mode switch every 5 seconds between usb and USB-D
If you are not scanning you can comment out the scan lines.? Then manually set your radio to the frequency and mode desired.? It will never change.
?
As long as you are scanning it will switch between data and not.
?
And John mentioned PTT_SETS_INPUT.? On my install I need that because I have both Pactor and Vara ports.? Do you have any hardware TNC ports?? If not you should be able to use PTT CAT or PTT CI-V instead and it may minimize or eliminate switching between modes like that.? In the end, whatever works for you...
?
--
73,
Mark, N5MDT
Montgomery, Texas
?
?
?
|
