开云体育

Well...I get RADIO 7 14.1075 LSB F1 W Sorry?-?Set?Mode?Command?Rejected Rick VA7RBP

The fields in a RADIO command (unlike scan lines) should be separated by spaces - RADIO 7 14.105 LSB F1W 73, John

Hi All I'm having some trouble trying to set up Rig Control using PILINBPQ VER 6.0.23.63 Radio is ICOM IC-756PROIII It appears that the only parameter that gets sent to the radio is the frequency,

This was working after all. I was just not getting the yellow and green color codes in the web GUI like I do for personals and bulls. Thanks, Chris KQ6UP

I am noticing that some traffic may be looping because I have NTS* as my outbound partner is the same as my inbound forwarding partner for NTSCA. I am wondering adding an exclamation mark in front of

This is my current Port config: PORT PORTNUM=3 ID=DirewolfVHF ;WinLink Gateway 145.030MHz TYPE=ASYNC PROTOCOL=KISS IPADDR=127.0.0.1 TCPPORT=8001 CHANNEL=A PACLEN=128 TXDELAY=500 FRACK=7000

Good Morning John, I think I may be a bit confused on your response, the only mode I have on HF is AX.25 300bps by way of Direwolf (via TCP) on another machine that handles the HF radio so I assume

PERMITTEDAPPLS only affects incoming connects on ax.25 ports. It doesn't affect the list of applications that is displayed by the Node ? command 73, John

No, it isn't possible to set a path for ID message. You can achieve a similar effect using beacons. 73, John

Jim - if there is a way to do it with the IDMSG: directive in the bpq32.cfg file I do not know or have long forgot how. My bpq32.cfg simply contains IDMSG: *** I then set the text and a digi using

If its possible, how do I specify a digi path for the IDMSG?? My VHF port is port 1, and would like to have the IDMSG digi'd through another packet station. Jim KI0BK

Yes, I have much of that going already, but I am not having luck with the zip code in the to: field. I get matches say K6HTN lives in 91104, and she gets tons of messages. I forward her matches to a

I have FBB attached to via a BPQ VirtualTNC (KANT Hostmode), I can connect just fine to the BPQ switch and beyond from FBB, but can I configure the converse? Thank you in advance, VY 73 de Chris KQ6UP

I seem to be running into an error where all the applications are listed on a port (in this case specifically the port assigned to HF) instead of only the permitted applications. Is there an

From my experience, you can't take the sdcard from a "3b" and put it in a "4" - it wont run ? Dave gm3yew - "jdfiberops@..." <packet@...> wrote:

Not enough info to provide any definite answers, Your pi may now have a different IP address as each network interface has a unique MAC address which is used by the automatic IP DHCP service on your

Thanks for the heads up! 73, Matt, WE1H Matt Atwood Merrimack, NH Phone / Text: 802-999-1994 Email: <mailto:we1h@...> we1h@... Web: <https://www.we1h.com/> www.we1h.com Sent: Tuesday,

I had to replace a failed Raspberry PI 3B on my RMS Gateway running bpq32 and now I can't access the BPQ32 node page. Removed the SD card from failed PI and placed into the new unit. Is there a config

Just wanted to update this for others, John you were correct, Changing my IDMSG did the trick! My config file has been corrected to:

I second Rich's thoughts.? I have a link to a forwarding partner that uses a satellite internet connection.? Our connection had to be configured as a TCP link rather than UDP.? He is the TCP-Master