Re: How to HF packet using SCS modem
Bleh, I did not format that.
Let me try again. :D
ATT 3
HFPACKET
C CALLSIGN
|
Re: How to HF packet using SCS modem
Jim,
I think for that modem it is similar to this:
For a normal (300 Baud HF Packet) call enter:
ATT 3
HFPACKET
C CALLSIGN
If you want to, and have configured, you can send after ATT(aching) the RADIO 14.1234 command. As long as you are attached and use INTERLOCK= or RADIO= on that PORT it should stop the scan until you remove the connection.
WinRPR, PTC-IIusb, Tracker(including Teensy Tracker) kind of share mostly the same command sets.
73
Kayne
From :
|
How to HF packet using SCS modem
Can't figure this one out, I want to connect to another station using HF packet ax.25, not robust packet, using my SCS PTC-IIusb.
I'm currently scanning for Pactor connects, so I need to halt scanning and set the frequency and ssb mode
before making my call to the other station. I can attach the port, stopping scanning, and use radio to set freq/mode ok
but then when I issue the connect callsign, it sends a pactor connect, not a packet connect.
If I disconnect, then I can issue a connect port callsign and the packet connect works ok, but then the radio starts scanning, not what I want.?? How to stop scanning and issue a packet connect?
?
|
Re: Killing zombie Bulls with dates older than XX days?
Odd, I have that set in housekeeping so not sure if thats working.
Say will it look at dates in the RLINES and determine it should be cleaned with housekeeping?
KH I've used in a pinch. That works ok, too.
|
Re: Killing zombie Bulls with dates older than XX days?
Housekeeping will remove messages older that the limits you've
specified in the housekeeping config. You can also kill all held
messages with KH.
73,
John
On 31/10/2024 02:08, N9SEO wrote:
toggle quoted message
Show quoted text
Hi,
Every once in a while someone makes a mistake and restores an
old bulletin (or some other behavior that gives this appearance)
and goes out to the network. Instead of getting them held, is
there some way to auto kill old bulls past say 60 days? I did
not see that in the given UI and perhaps I overlooked something
somewhere. I do not see a reason for a bulletin to be
regurgitated back upon the network when it has already expired
out of most of our systems. If there is some lack of sight on my
part let me know too.
|
Killing zombie Bulls with dates older than XX days?
Hi,
Every once in a while someone makes a mistake and restores an old bulletin (or some other behavior that gives this appearance) and goes out to the network. Instead of getting them held, is there some way to auto kill old bulls past say 60 days? I did not see that in the given UI and perhaps I overlooked something somewhere. I do not see a reason for a bulletin to be regurgitated back upon the network when it has already expired out of most of our systems. If there is some lack of sight on my part let me know too.
|
Re: Possible QtTermTCP Bug
Sorry, I thought I'd fixed that. I'll look into it.
73, John
toggle quoted message
Show quoted text
On 28/10/2024 21:11, Rich Sahlender via groups.io wrote: A segfault occurs in QtTermTCP on both 32bit and 64bit x86 systems while attempting a K2K session between two instances of QtTermTCP without any node software in between, with QTT configured for the default split screen mode "Single Window (Term + Mon)", and using the AGW interface with QtSoundModem. The segfault does not occur if QTT is configured for Single Window (Term only), MDI, or Tabbed. It also does not occur if using KISS rather than AGW.
I attempted to describe this back in January at /g/bpq32/message/40577 and followed up with a patch against QtTermTCP in February at /g/bpq32/message/40647 that solved the issue here. In this specific instance it was while using QtTermTCP 0.0.0.73. The segfault continues to occur with the latest QTT 0.0.0.77 Beta 1.
I read where others were using QTT for direct K2K sessions so assume I am not using QTT for something it was not intended for... if I am then please ignore this post!
The segfault is easy to reproduce using two systems which for this example I am calling system A and system B. Start QTS on both A and B with AGW enabled on a port of your choosing. I used the default port 8000 for testing.
Start a fresh copy of QTT on both system A and B letting QTT create a new .ini file. On both A and B systems enable QTT Listen on the default port 8015. Again on both A and B within the QTT AGW Setup enable both the interface and the monitor and set Ports to 1. Then set a unique Terminal Call for each and make sure the port in the AGW tnc setup sections match whatever port was specified for AGW in QTS. Save the QTT config then stop and restart QTT.
An AGW connect from either A to B or from B to A works. To reproduce the segfault simply attempt sending something TO the system that issued the connect FROM the system that was connected to. A gdb backtrace should look very similar to the one I provided at /g/bpq32/message/40577 .
I reworked the original QTT .73 patch and attached it for use with QTT .77 Beta 1 source. Rework or ignore as seen fit.
73 de Rich WA3WLH
|
Re: Possible QtTermTCP Bug
Thanks, Rich.? Em seg., 28 de out. de 2024, 18:12, Rich Sahlender via <wa3wlh= [email protected]> escreveu:
A segfault occurs in QtTermTCP on both 32bit and 64bit x86 systems while
attempting a K2K session between two instances of QtTermTCP without any
node software in between, with QTT configured for the default split
screen mode "Single Window (Term + Mon)", and using the AGW interface
with QtSoundModem. The segfault does not occur if QTT is configured for
Single Window (Term only), MDI, or Tabbed. It also does not occur if
using KISS rather than AGW.
I attempted to describe this back in January at
/g/bpq32/message/40577 and followed up with a patch
against QtTermTCP in February at /g/bpq32/message/40647
that solved the issue here. In this specific instance it was while using
QtTermTCP 0.0.0.73. The segfault continues to occur with the latest QTT
0.0.0.77 Beta 1.
I read where others were using QTT for direct K2K sessions so assume I
am not using QTT for something it was not intended for... if I am then
please ignore this post!
The segfault is easy to reproduce using two systems which for this
example I am calling system A and system B. Start QTS on both A and B
with AGW enabled on a port of your choosing. I used the default port
8000 for testing.
Start a fresh copy of QTT on both system A and B letting QTT create a
new .ini file. On both A and B systems enable QTT Listen on the default
port 8015. Again on both A and B within the QTT AGW Setup enable both
the interface and the monitor and set Ports to 1. Then set a unique
Terminal Call for each and make sure the port in the AGW tnc setup
sections match whatever port was specified for AGW in QTS. Save the QTT
config then stop and restart QTT.
An AGW connect from either A to B or from B to A works. To reproduce the
segfault simply attempt sending something TO the system that issued the
connect FROM the system that was connected to. A gdb backtrace should
look very similar to the one I provided at
/g/bpq32/message/40577 .
I reworked the original QTT .73 patch and attached it for use with QTT
.77 Beta 1 source. Rework or ignore as seen fit.
73 de Rich WA3WLH
|
A segfault occurs in QtTermTCP on both 32bit and 64bit x86 systems while attempting a K2K session between two instances of QtTermTCP without any node software in between, with QTT configured for the default split screen mode "Single Window (Term + Mon)", and using the AGW interface with QtSoundModem. The segfault does not occur if QTT is configured for Single Window (Term only), MDI, or Tabbed. It also does not occur if using KISS rather than AGW. I attempted to describe this back in January at /g/bpq32/message/40577 and followed up with a patch against QtTermTCP in February at /g/bpq32/message/40647 that solved the issue here. In this specific instance it was while using QtTermTCP 0.0.0.73. The segfault continues to occur with the latest QTT 0.0.0.77 Beta 1. I read where others were using QTT for direct K2K sessions so assume I am not using QTT for something it was not intended for... if I am then please ignore this post! The segfault is easy to reproduce using two systems which for this example I am calling system A and system B. Start QTS on both A and B with AGW enabled on a port of your choosing. I used the default port 8000 for testing. Start a fresh copy of QTT on both system A and B letting QTT create a new .ini file. On both A and B systems enable QTT Listen on the default port 8015. Again on both A and B within the QTT AGW Setup enable both the interface and the monitor and set Ports to 1. Then set a unique Terminal Call for each and make sure the port in the AGW tnc setup sections match whatever port was specified for AGW in QTS. Save the QTT config then stop and restart QTT. An AGW connect from either A to B or from B to A works. To reproduce the segfault simply attempt sending something TO the system that issued the connect FROM the system that was connected to. A gdb backtrace should look very similar to the one I provided at /g/bpq32/message/40577 . I reworked the original QTT .73 patch and attached it for use with QTT .77 Beta 1 source. Rework or ignore as seen fit. 73 de Rich WA3WLH
|
Re: Connect Showing Robust Packet
I'm seeing the same thing when using a Dragon and connecting with Winlink, completely separate from BPQ.? I believe it is a Dragon thing, not a BPQ thing.
?
?
|
Re: Connect Showing Robust Packet
I¡¯m seeing this in the log sometimes as well, I¡¯m using a PTC IIusb.
Connections to the bbs are normal and working ok as far as I can tell.
?
|
Re: Outgoing Pactor connections fail, income connections OK [Solution]
Found the missing setting!
added setting mycall to the config section of the pactor port.
this parameter sets the modem's callsign to use on outgoing connects!
?
PORT X
....
Config
....
? MYcall KI0BK
....
ENDPORT
?
|
I'm glad you've found the problem but it shouldn't segfault so I'll look at that.
73, John
toggle quoted message
Show quoted text
On 26/10/2024 05:44, Niels PD9Q wrote: Ok, found the problem.....
I had a forward script where a couple of lines started with a #
Something like this...
#att 1
#c gb7iow
#bbs
This gives a seg fault...
If you have something like this...
#att 1
#c gb7iow
#bbs
times 0800-1959
att 5
radio 7.049450 USB-D
c gb7iow
bbs
There is no problem.
Sorry about the noise.
I still don`t understand why I put a #hash in front of it ;)
73 Niels PD9Q
Op 25-10-2024 om 21:39 schreef John G8BPQ:
Can you look in the BBS log and see if it has recorded the call of the bbs it is trying to connect to. The segfault may have disrupted the logging, but if not disable forwarding the the bbs it was trying to connect to and check the connect script. If there isn't anything helpful in the log you could try starting forwarding to each bbs in turn and see which one is causing the problem..
73,
John
On 25/10/2024 18:14, Niels PD9Q wrote:
Hi John,
Just the same output...
Thread 1 "pilinbpq" received signal SIGSEGV, Segmentation fault.
0x00129f98 in memicmp (a=0x0, b=0x265dc4 "TIMES", n=5) at /mnt/Source/bpq32/CommonSource/compatbits.c:72
72????? /mnt/Source/bpq32/CommonSource/compatbits.c: Bestand of map bestaat niet.
(gdb)
(gdb) (here are the enters)
(gdb) bt
#0? 0x00129f98 in memicmp (a=0x0, b=0x265dc4 "TIMES", n=5) at /mnt/Source/bpq32/CommonSource/compatbits.c:72
#1? 0x000eda88 in ProcessBBSConnectScript (conn=0x3bd118 <Connections+5568>, Buffer=0x7efff3f8 "*** CONNECTED? ", len=15) at /mnt/Source/bpq32/CommonSource/BBSUtilities.c:8139
#2? 0x000f5eac in Connected (Stream=19) at /mnt/Source/bpq32/CommonSource/BBSUtilities.c:10496
#3? 0x001681e4 in PollStreams () at /mnt/Source/bpq32/CommonSource/LinBPQ.c:2041
#4? 0x001676c8 in main (argc=1, argv=0x7efff774) at /mnt/Source/bpq32/CommonSource/LinBPQ.c:1555
(gdb)
I delete all the times in the forward scripts.....
For help, type "help".
Type "apropos word" to search for commands related to "word"...
Reading symbols from ./pilinbpq...done.
(gdb) r
Starting program: /home/pi/linbpq/pilinbpq
[Thread debugging using libthread_db enabled]
Using host libthread_db library "/lib/arm-linux-gnueabihf/libthread_db.so.1".
G8BPQ AX25 Packet Switch System Version 6.0.24.47 October 2024
Copyright ? 2001-2024 John Wiseman G8BPQ
Current Directory is /home/pi/linbpq
Log Directory is /home/pi/linbpq
Making Directory /home/pi/linbpq/logs
Configuration file Preprocessor.
Using Configuration file /home/pi/linbpq/bpq32.cfg
Conversion (probably) successful
PORTS 0x2eb320 LINKS 0x2f2b30 DESTS 0x2f6640 ROUTES 0x303640 L4 0x306a40 BUFFERS 0x314380
[New Thread 0x76d64440 (LWP 13385)]
Initialising Port 01???? UZ7HO Host 44.137.31.76 Port 8101 Chan A
[New Thread 0x76563440 (LWP 13386)]
Initialising Port 02???? UZ7HO Host 44.137.31.76 Port 8101 Chan B
Initialising Port 03???? ARDOP Host 44.137.31.76 8515
[New Thread 0x75d62440 (LWP 13387)]
Initialising Port 04???? VARA Host 44.137.31.76 8300
[New Thread 0x75561440 (LWP 13388)]
Initialising Port 05???? UZ7HO Host 44.137.31.76 Port 8101 Chan C
Initialising Port 06???? ASYNC /dev/ttyUSB0 Chan A
[New Thread 0x74d60440 (LWP 13389)]
[New Thread 0x7455f440 (LWP 13390)]
Initialising Port 07???? AXIP
[Thread 0x7455f440 (LWP 13390) exited]
[New Thread 0x7455f440 (LWP 13391)]
Initialising Port 08???? Telnet Server
[New Thread 0x739ff440 (LWP 13392)]
Rig Control Enabled
[New Thread 0x731fe440 (LWP 13393)]
MQTT Enabled 0
[New Thread 0x729fd440 (LWP 13394)]
Starting Chat
Config File is /home/pi/linbpq/chatconfig.cfg
Chat Started
Starting Mail
Config File is /home/pi/linbpq/linmail.cfg
Config Processed
[Thread 0x7455f440 (LWP 13391) exited]
[New Thread 0x7455f440 (LWP 13401)]
[New Thread 0x72184440 (LWP 13402)]
Mail Started
slave device: /dev/pts/0. symlink to /home/pi/fbbded created
TNC Emulator Init Complete
[New Thread 0x71983440 (LWP 13403)]
[Thread 0x76563440 (LWP 13386) exited]
Connected to ARDOP TNC Port 3
Connected to VARA TNC Port 4
[New Thread 0x76563440 (LWP 17063)]
[Thread 0x76563440 (LWP 17063) exited]
[New Thread 0x76563440 (LWP 20741)]
[Thread 0x76563440 (LWP 20741) exited]
[New Thread 0x76563440 (LWP 24399)]
[Thread 0x76563440 (LWP 24399) exited]
[New Thread 0x76563440 (LWP 28060)]
[Thread 0x76563440 (LWP 28060) exited]
Thread 1 "pilinbpq" received signal SIGSEGV, Segmentation fault.
0x00129f98 in memicmp (a=0x0, b=0x265dc4 "TIMES", n=5) at /mnt/Source/bpq32/CommonSource/compatbits.c:72
72????? /mnt/Source/bpq32/CommonSource/compatbits.c: Bestand of map bestaat niet.
(gdb)
(gdb)
(gdb) bt
#0? 0x00129f98 in memicmp (a=0x0, b=0x265dc4 "TIMES", n=5) at /mnt/Source/bpq32/CommonSource/compatbits.c:72
#1? 0x000eda88 in ProcessBBSConnectScript (conn=0x3bd118 <Connections+5568>, Buffer=0x7efff3f8 "*** CONNECTED? ", len=15) at /mnt/Source/bpq32/CommonSource/BBSUtilities.c:8139
#2? 0x000f5eac in Connected (Stream=19) at /mnt/Source/bpq32/CommonSource/BBSUtilities.c:10496
#3? 0x001681e4 in PollStreams () at /mnt/Source/bpq32/CommonSource/LinBPQ.c:2041
#4? 0x001676c8 in main (argc=1, argv=0x7efff774) at /mnt/Source/bpq32/CommonSource/LinBPQ.c:1555
(gdb) quit
A debugging session is active.
??????? Inferior 1 [process 13376] will be killed.
Quit anyway? (y or n) y
73 Niels PD9Q
Op 25-10-2024 om 13:07 schreef John G8BPQ:
Can you try running under gdb?
Thanks,
John
On 25/10/2024 05:37, Niels PD9Q wrote:
Hi,
Lately I've been having? about every hour a segmentation fault with pilinbpq.
I don`t understand why.
Thanks.
73 Niels PD9Q
Oct 24 05:30:52 pi1lap bash[19835]: /home/pi/linbpq/linbpq.start: regel 11: 19838 Segmentatiefout???????? ./pilinbpq
Oct 24 05:30:52 pi1lap systemd[1]: linbpq.service: Main process exited, code=exited, status=139/n/a
Oct 24 05:30:52 pi1lap systemd[1]: linbpq.service: Failed with result 'exit-code'.
Oct 24 05:30:57 pi1lap systemd[1]: linbpq.service: Service RestartSec=5s expired, scheduling restart.
Oct 24 05:30:57 pi1lap systemd[1]: linbpq.service: Scheduled restart job, restart counter is at 23.
Oct 24 05:30:57 pi1lap systemd[1]: Stopped Linbpq Daemon.
Oct 24 05:30:57 pi1lap systemd[1]: Started Linbpq Daemon.
Oct 24 05:30:57 pi1lap bash[2341]: G8BPQ AX25 Packet Switch System Version 6.0.24.47 October 2024
pi@pi1lap:~/linbpq $ sudo gdb ./pilinbpq
GNU gdb (Raspbian 8.2.1-2) 8.2.1
Copyright (C) 2018 Free Software Foundation, Inc.
License GPLv3+: GNU GPL version 3 or later <>
This is free software: you are free to change and redistribute it.
There is NO WARRANTY, to the extent permitted by law.
Type "show copying" and "show warranty" for details.
This GDB was configured as "arm-linux-gnueabihf".
Type "show configuration" for configuration details.
For bug reporting instructions, please see:
<>.
Find the GDB manual and other documentation resources online at:
<>.
For help, type "help".
Type "apropos word" to search for commands related to "word"...
Reading symbols from ./pilinbpq...done.
(gdb) r
Starting program: /home/pi/linbpq/pilinbpq
[Thread debugging using libthread_db enabled]
Using host libthread_db library "/lib/arm-linux-gnueabihf/libthread_db.so.1".
G8BPQ AX25 Packet Switch System Version 6.0.24.47 October 2024
Copyright ? 2001-2024 John Wiseman G8BPQ
Current Directory is /home/pi/linbpq
Log Directory is /home/pi/linbpq
Making Directory /home/pi/linbpq/logs
Configuration file Preprocessor.
Using Configuration file /home/pi/linbpq/bpq32.cfg
Conversion (probably) successful
PORTS 0x2eb320 LINKS 0x2f2b30 DESTS 0x2f6640 ROUTES 0x303640 L4 0x306a40 BUFFERS 0x314380
[New Thread 0x76d64440 (LWP 30794)]
Initialising Port 01???? UZ7HO Host 44.137.31.76 Port 8101 Chan A
[New Thread 0x76563440 (LWP 30795)]
Initialising Port 02???? UZ7HO Host 44.137.31.76 Port 8101 Chan B
Initialising Port 03???? ARDOP Host 44.137.31.76 8515
[New Thread 0x75d62440 (LWP 30796)]
Initialising Port 04???? VARA Host 44.137.31.76 8300
[New Thread 0x75561440 (LWP 30797)]
Initialising Port 05???? UZ7HO Host 44.137.31.76 Port 8101 Chan C
Initialising Port 06???? ASYNC /dev/ttyUSB0 Chan A
[New Thread 0x74d60440 (LWP 30798)]
[New Thread 0x7455f440 (LWP 30799)]
Initialising Port 07???? AXIP
[New Thread 0x739ff440 (LWP 30800)]
Initialising Port 08???? Telnet Server
[New Thread 0x7455f440 (LWP 30801)]
[Thread 0x7455f440 (LWP 30799) exited]
Rig Control Enabled
[New Thread 0x731fe440 (LWP 30802)]
MQTT Enabled 0
[New Thread 0x729fd440 (LWP 30803)]
Starting Chat
Config File is /home/pi/linbpq/chatconfig.cfg
Chat Started
Starting Mail
Config File is /home/pi/linbpq/linmail.cfg
Config Processed
[Thread 0x739ff440 (LWP 30800) exited]
[New Thread 0x739ff440 (LWP 30808)]
[New Thread 0x721e7440 (LWP 30809)]
Mail Started
slave device: /dev/pts/0. symlink to /home/pi/fbbded created
TNC Emulator Init Complete
[New Thread 0x719e6440 (LWP 30810)]
[Thread 0x76563440 (LWP 30795) exited]
Connected to ARDOP TNC Port 3
Connected to VARA TNC Port 4
[New Thread 0x76563440 (LWP 744)]
[Thread 0x76563440 (LWP 744) exited]
[New Thread 0x76563440 (LWP 2172)]
[Thread 0x76563440 (LWP 2172) exited]
[New Thread 0x76563440 (LWP 5892)]
[Thread 0x76563440 (LWP 5892) exited]
[New Thread 0x76563440 (LWP 9581)]
[Thread 0x76563440 (LWP 9581) exited]
[New Thread 0x76563440 (LWP 13243)]
[Thread 0x76563440 (LWP 13243) exited]
Thread 1 "pilinbpq" received signal SIGSEGV, Segmentation fault.
0x00129f98 in memicmp (a=0x0, b=0x265dc4 "TIMES", n=5) at /mnt/Source/bpq32/CommonSource/compatbits.c:72
72????? /mnt/Source/bpq32/CommonSource/compatbits.c: Bestand of map bestaat niet.
(gdb) bt
#0? 0x00129f98 in memicmp (a=0x0, b=0x265dc4 "TIMES", n=5) at /mnt/Source/bpq32/CommonSource/compatbits.c:72
#1? 0x000eda88 in ProcessBBSConnectScript (conn=0x3bce60 <Connections+4872>, Buffer=0x7efff3f8 "*** CONNECTED ", len=15) at /mnt/Source/bpq32/CommonSource/BBSUtilities.c:8139
#2? 0x000f5eac in Connected (Stream=18) at /mnt/Source/bpq32/CommonSource/BBSUtilities.c:10496
#3? 0x001681e4 in PollStreams () at /mnt/Source/bpq32/CommonSource/LinBPQ.c:2041
#4? 0x001676c8 in main (argc=1, argv=0x7efff774) at /mnt/Source/bpq32/CommonSource/LinBPQ.c:1555
(gdb)
|
Ok, found the problem.....
I had a forward script where a couple of lines started with a #
Something like this...
#att 1
#c gb7iow
#bbs
This gives a seg fault...
If you have something like this...
#att 1
#c gb7iow
#bbs
times 0800-1959
att 5
radio 7.049450 USB-D
c gb7iow
bbs
There is no problem.
Sorry about the noise.
I still don`t understand why I put a #hash in front of it ;)
73 Niels PD9Q
Op 25-10-2024 om 21:39 schreef John G8BPQ:
toggle quoted message
Show quoted text
Can you look in the BBS log and see if it has recorded the call of the bbs it is trying to connect to. The segfault may have disrupted the logging, but if not disable forwarding the the bbs it was trying to connect to and check the connect script. If there isn't anything helpful in the log you could try starting forwarding to each bbs in turn and see which one is causing the problem..
73,
John
On 25/10/2024 18:14, Niels PD9Q wrote:
Hi John,
Just the same output...
Thread 1 "pilinbpq" received signal SIGSEGV, Segmentation fault.
0x00129f98 in memicmp (a=0x0, b=0x265dc4 "TIMES", n=5) at /mnt/Source/bpq32/CommonSource/compatbits.c:72
72????? /mnt/Source/bpq32/CommonSource/compatbits.c: Bestand of map bestaat niet.
(gdb)
(gdb) (here are the enters)
(gdb) bt
#0? 0x00129f98 in memicmp (a=0x0, b=0x265dc4 "TIMES", n=5) at /mnt/Source/bpq32/CommonSource/compatbits.c:72
#1? 0x000eda88 in ProcessBBSConnectScript (conn=0x3bd118 <Connections+5568>, Buffer=0x7efff3f8 "*** CONNECTED? ", len=15) at /mnt/Source/bpq32/CommonSource/BBSUtilities.c:8139
#2? 0x000f5eac in Connected (Stream=19) at /mnt/Source/bpq32/CommonSource/BBSUtilities.c:10496
#3? 0x001681e4 in PollStreams () at /mnt/Source/bpq32/CommonSource/LinBPQ.c:2041
#4? 0x001676c8 in main (argc=1, argv=0x7efff774) at /mnt/Source/bpq32/CommonSource/LinBPQ.c:1555
(gdb)
I delete all the times in the forward scripts.....
For help, type "help".
Type "apropos word" to search for commands related to "word"...
Reading symbols from ./pilinbpq...done.
(gdb) r
Starting program: /home/pi/linbpq/pilinbpq
[Thread debugging using libthread_db enabled]
Using host libthread_db library "/lib/arm-linux-gnueabihf/libthread_db.so.1".
G8BPQ AX25 Packet Switch System Version 6.0.24.47 October 2024
Copyright ? 2001-2024 John Wiseman G8BPQ
Current Directory is /home/pi/linbpq
Log Directory is /home/pi/linbpq
Making Directory /home/pi/linbpq/logs
Configuration file Preprocessor.
Using Configuration file /home/pi/linbpq/bpq32.cfg
Conversion (probably) successful
PORTS 0x2eb320 LINKS 0x2f2b30 DESTS 0x2f6640 ROUTES 0x303640 L4 0x306a40 BUFFERS 0x314380
[New Thread 0x76d64440 (LWP 13385)]
Initialising Port 01???? UZ7HO Host 44.137.31.76 Port 8101 Chan A
[New Thread 0x76563440 (LWP 13386)]
Initialising Port 02???? UZ7HO Host 44.137.31.76 Port 8101 Chan B
Initialising Port 03???? ARDOP Host 44.137.31.76 8515
[New Thread 0x75d62440 (LWP 13387)]
Initialising Port 04???? VARA Host 44.137.31.76 8300
[New Thread 0x75561440 (LWP 13388)]
Initialising Port 05???? UZ7HO Host 44.137.31.76 Port 8101 Chan C
Initialising Port 06???? ASYNC /dev/ttyUSB0 Chan A
[New Thread 0x74d60440 (LWP 13389)]
[New Thread 0x7455f440 (LWP 13390)]
Initialising Port 07???? AXIP
[Thread 0x7455f440 (LWP 13390) exited]
[New Thread 0x7455f440 (LWP 13391)]
Initialising Port 08???? Telnet Server
[New Thread 0x739ff440 (LWP 13392)]
Rig Control Enabled
[New Thread 0x731fe440 (LWP 13393)]
MQTT Enabled 0
[New Thread 0x729fd440 (LWP 13394)]
Starting Chat
Config File is /home/pi/linbpq/chatconfig.cfg
Chat Started
Starting Mail
Config File is /home/pi/linbpq/linmail.cfg
Config Processed
[Thread 0x7455f440 (LWP 13391) exited]
[New Thread 0x7455f440 (LWP 13401)]
[New Thread 0x72184440 (LWP 13402)]
Mail Started
slave device: /dev/pts/0. symlink to /home/pi/fbbded created
TNC Emulator Init Complete
[New Thread 0x71983440 (LWP 13403)]
[Thread 0x76563440 (LWP 13386) exited]
Connected to ARDOP TNC Port 3
Connected to VARA TNC Port 4
[New Thread 0x76563440 (LWP 17063)]
[Thread 0x76563440 (LWP 17063) exited]
[New Thread 0x76563440 (LWP 20741)]
[Thread 0x76563440 (LWP 20741) exited]
[New Thread 0x76563440 (LWP 24399)]
[Thread 0x76563440 (LWP 24399) exited]
[New Thread 0x76563440 (LWP 28060)]
[Thread 0x76563440 (LWP 28060) exited]
Thread 1 "pilinbpq" received signal SIGSEGV, Segmentation fault.
0x00129f98 in memicmp (a=0x0, b=0x265dc4 "TIMES", n=5) at /mnt/Source/bpq32/CommonSource/compatbits.c:72
72????? /mnt/Source/bpq32/CommonSource/compatbits.c: Bestand of map bestaat niet.
(gdb)
(gdb)
(gdb) bt
#0? 0x00129f98 in memicmp (a=0x0, b=0x265dc4 "TIMES", n=5) at /mnt/Source/bpq32/CommonSource/compatbits.c:72
#1? 0x000eda88 in ProcessBBSConnectScript (conn=0x3bd118 <Connections+5568>, Buffer=0x7efff3f8 "*** CONNECTED? ", len=15) at /mnt/Source/bpq32/CommonSource/BBSUtilities.c:8139
#2? 0x000f5eac in Connected (Stream=19) at /mnt/Source/bpq32/CommonSource/BBSUtilities.c:10496
#3? 0x001681e4 in PollStreams () at /mnt/Source/bpq32/CommonSource/LinBPQ.c:2041
#4? 0x001676c8 in main (argc=1, argv=0x7efff774) at /mnt/Source/bpq32/CommonSource/LinBPQ.c:1555
(gdb) quit
A debugging session is active.
??????? Inferior 1 [process 13376] will be killed.
Quit anyway? (y or n) y
73 Niels PD9Q
Op 25-10-2024 om 13:07 schreef John G8BPQ:
Can you try running under gdb?
Thanks,
John
On 25/10/2024 05:37, Niels PD9Q wrote:
Hi,
Lately I've been having? about every hour a segmentation fault with pilinbpq.
I don`t understand why.
Thanks.
73 Niels PD9Q
Oct 24 05:30:52 pi1lap bash[19835]: /home/pi/linbpq/linbpq.start: regel 11: 19838 Segmentatiefout???????? ./pilinbpq
Oct 24 05:30:52 pi1lap systemd[1]: linbpq.service: Main process exited, code=exited, status=139/n/a
Oct 24 05:30:52 pi1lap systemd[1]: linbpq.service: Failed with result 'exit-code'.
Oct 24 05:30:57 pi1lap systemd[1]: linbpq.service: Service RestartSec=5s expired, scheduling restart.
Oct 24 05:30:57 pi1lap systemd[1]: linbpq.service: Scheduled restart job, restart counter is at 23.
Oct 24 05:30:57 pi1lap systemd[1]: Stopped Linbpq Daemon.
Oct 24 05:30:57 pi1lap systemd[1]: Started Linbpq Daemon.
Oct 24 05:30:57 pi1lap bash[2341]: G8BPQ AX25 Packet Switch System Version 6.0.24.47 October 2024
pi@pi1lap:~/linbpq $ sudo gdb ./pilinbpq
GNU gdb (Raspbian 8.2.1-2) 8.2.1
Copyright (C) 2018 Free Software Foundation, Inc.
License GPLv3+: GNU GPL version 3 or later <>
This is free software: you are free to change and redistribute it.
There is NO WARRANTY, to the extent permitted by law.
Type "show copying" and "show warranty" for details.
This GDB was configured as "arm-linux-gnueabihf".
Type "show configuration" for configuration details.
For bug reporting instructions, please see:
<>.
Find the GDB manual and other documentation resources online at:
??? <>.
For help, type "help".
Type "apropos word" to search for commands related to "word"...
Reading symbols from ./pilinbpq...done.
(gdb) r
Starting program: /home/pi/linbpq/pilinbpq
[Thread debugging using libthread_db enabled]
Using host libthread_db library "/lib/arm-linux-gnueabihf/libthread_db.so.1".
G8BPQ AX25 Packet Switch System Version 6.0.24.47 October 2024
Copyright ? 2001-2024 John Wiseman G8BPQ
Current Directory is /home/pi/linbpq
Log Directory is /home/pi/linbpq
Making Directory /home/pi/linbpq/logs
Configuration file Preprocessor.
Using Configuration file /home/pi/linbpq/bpq32.cfg
Conversion (probably) successful
PORTS 0x2eb320 LINKS 0x2f2b30 DESTS 0x2f6640 ROUTES 0x303640 L4 0x306a40 BUFFERS 0x314380
[New Thread 0x76d64440 (LWP 30794)]
Initialising Port 01???? UZ7HO Host 44.137.31.76 Port 8101 Chan A
[New Thread 0x76563440 (LWP 30795)]
Initialising Port 02???? UZ7HO Host 44.137.31.76 Port 8101 Chan B
Initialising Port 03???? ARDOP Host 44.137.31.76 8515
[New Thread 0x75d62440 (LWP 30796)]
Initialising Port 04???? VARA Host 44.137.31.76 8300
[New Thread 0x75561440 (LWP 30797)]
Initialising Port 05???? UZ7HO Host 44.137.31.76 Port 8101 Chan C
Initialising Port 06???? ASYNC /dev/ttyUSB0 Chan A
[New Thread 0x74d60440 (LWP 30798)]
[New Thread 0x7455f440 (LWP 30799)]
Initialising Port 07???? AXIP
[New Thread 0x739ff440 (LWP 30800)]
Initialising Port 08???? Telnet Server
[New Thread 0x7455f440 (LWP 30801)]
[Thread 0x7455f440 (LWP 30799) exited]
Rig Control Enabled
[New Thread 0x731fe440 (LWP 30802)]
MQTT Enabled 0
[New Thread 0x729fd440 (LWP 30803)]
Starting Chat
Config File is /home/pi/linbpq/chatconfig.cfg
Chat Started
Starting Mail
Config File is /home/pi/linbpq/linmail.cfg
Config Processed
[Thread 0x739ff440 (LWP 30800) exited]
[New Thread 0x739ff440 (LWP 30808)]
[New Thread 0x721e7440 (LWP 30809)]
Mail Started
slave device: /dev/pts/0. symlink to /home/pi/fbbded created
TNC Emulator Init Complete
[New Thread 0x719e6440 (LWP 30810)]
[Thread 0x76563440 (LWP 30795) exited]
Connected to ARDOP TNC Port 3
Connected to VARA TNC Port 4
[New Thread 0x76563440 (LWP 744)]
[Thread 0x76563440 (LWP 744) exited]
[New Thread 0x76563440 (LWP 2172)]
[Thread 0x76563440 (LWP 2172) exited]
[New Thread 0x76563440 (LWP 5892)]
[Thread 0x76563440 (LWP 5892) exited]
[New Thread 0x76563440 (LWP 9581)]
[Thread 0x76563440 (LWP 9581) exited]
[New Thread 0x76563440 (LWP 13243)]
[Thread 0x76563440 (LWP 13243) exited]
Thread 1 "pilinbpq" received signal SIGSEGV, Segmentation fault.
0x00129f98 in memicmp (a=0x0, b=0x265dc4 "TIMES", n=5) at /mnt/Source/bpq32/CommonSource/compatbits.c:72
72????? /mnt/Source/bpq32/CommonSource/compatbits.c: Bestand of map bestaat niet.
(gdb) bt
#0? 0x00129f98 in memicmp (a=0x0, b=0x265dc4 "TIMES", n=5) at /mnt/Source/bpq32/CommonSource/compatbits.c:72
#1? 0x000eda88 in ProcessBBSConnectScript (conn=0x3bce60 <Connections+4872>, Buffer=0x7efff3f8 "*** CONNECTED ", len=15) at /mnt/Source/bpq32/CommonSource/BBSUtilities.c:8139
#2? 0x000f5eac in Connected (Stream=18) at /mnt/Source/bpq32/CommonSource/BBSUtilities.c:10496
#3? 0x001681e4 in PollStreams () at /mnt/Source/bpq32/CommonSource/LinBPQ.c:2041
#4? 0x001676c8 in main (argc=1, argv=0x7efff774) at /mnt/Source/bpq32/CommonSource/LinBPQ.c:1555
(gdb)
|
Can you look in the BBS log and see if it has recorded the call of the bbs it is trying to connect to. The segfault may have disrupted the logging, but if not disable forwarding the the bbs it was trying to connect to and check the connect script. If there isn't anything helpful in the log you could try starting forwarding to each bbs in turn and see which one is causing the problem..
73,
John
toggle quoted message
Show quoted text
On 25/10/2024 18:14, Niels PD9Q wrote: Hi John,
Just the same output...
Thread 1 "pilinbpq" received signal SIGSEGV, Segmentation fault.
0x00129f98 in memicmp (a=0x0, b=0x265dc4 "TIMES", n=5) at /mnt/Source/bpq32/CommonSource/compatbits.c:72
72????? /mnt/Source/bpq32/CommonSource/compatbits.c: Bestand of map bestaat niet.
(gdb)
(gdb) (here are the enters)
(gdb) bt
#0? 0x00129f98 in memicmp (a=0x0, b=0x265dc4 "TIMES", n=5) at /mnt/Source/bpq32/CommonSource/compatbits.c:72
#1? 0x000eda88 in ProcessBBSConnectScript (conn=0x3bd118 <Connections+5568>, Buffer=0x7efff3f8 "*** CONNECTED? ", len=15) at /mnt/Source/bpq32/CommonSource/BBSUtilities.c:8139
#2? 0x000f5eac in Connected (Stream=19) at /mnt/Source/bpq32/CommonSource/BBSUtilities.c:10496
#3? 0x001681e4 in PollStreams () at /mnt/Source/bpq32/CommonSource/LinBPQ.c:2041
#4? 0x001676c8 in main (argc=1, argv=0x7efff774) at /mnt/Source/bpq32/CommonSource/LinBPQ.c:1555
(gdb)
I delete all the times in the forward scripts.....
For help, type "help".
Type "apropos word" to search for commands related to "word"...
Reading symbols from ./pilinbpq...done.
(gdb) r
Starting program: /home/pi/linbpq/pilinbpq
[Thread debugging using libthread_db enabled]
Using host libthread_db library "/lib/arm-linux-gnueabihf/libthread_db.so.1".
G8BPQ AX25 Packet Switch System Version 6.0.24.47 October 2024
Copyright ? 2001-2024 John Wiseman G8BPQ
Current Directory is /home/pi/linbpq
Log Directory is /home/pi/linbpq
Making Directory /home/pi/linbpq/logs
Configuration file Preprocessor.
Using Configuration file /home/pi/linbpq/bpq32.cfg
Conversion (probably) successful
PORTS 0x2eb320 LINKS 0x2f2b30 DESTS 0x2f6640 ROUTES 0x303640 L4 0x306a40 BUFFERS 0x314380
[New Thread 0x76d64440 (LWP 13385)]
Initialising Port 01???? UZ7HO Host 44.137.31.76 Port 8101 Chan A
[New Thread 0x76563440 (LWP 13386)]
Initialising Port 02???? UZ7HO Host 44.137.31.76 Port 8101 Chan B
Initialising Port 03???? ARDOP Host 44.137.31.76 8515
[New Thread 0x75d62440 (LWP 13387)]
Initialising Port 04???? VARA Host 44.137.31.76 8300
[New Thread 0x75561440 (LWP 13388)]
Initialising Port 05???? UZ7HO Host 44.137.31.76 Port 8101 Chan C
Initialising Port 06???? ASYNC /dev/ttyUSB0 Chan A
[New Thread 0x74d60440 (LWP 13389)]
[New Thread 0x7455f440 (LWP 13390)]
Initialising Port 07???? AXIP
[Thread 0x7455f440 (LWP 13390) exited]
[New Thread 0x7455f440 (LWP 13391)]
Initialising Port 08???? Telnet Server
[New Thread 0x739ff440 (LWP 13392)]
Rig Control Enabled
[New Thread 0x731fe440 (LWP 13393)]
MQTT Enabled 0
[New Thread 0x729fd440 (LWP 13394)]
Starting Chat
Config File is /home/pi/linbpq/chatconfig.cfg
Chat Started
Starting Mail
Config File is /home/pi/linbpq/linmail.cfg
Config Processed
[Thread 0x7455f440 (LWP 13391) exited]
[New Thread 0x7455f440 (LWP 13401)]
[New Thread 0x72184440 (LWP 13402)]
Mail Started
slave device: /dev/pts/0. symlink to /home/pi/fbbded created
TNC Emulator Init Complete
[New Thread 0x71983440 (LWP 13403)]
[Thread 0x76563440 (LWP 13386) exited]
Connected to ARDOP TNC Port 3
Connected to VARA TNC Port 4
[New Thread 0x76563440 (LWP 17063)]
[Thread 0x76563440 (LWP 17063) exited]
[New Thread 0x76563440 (LWP 20741)]
[Thread 0x76563440 (LWP 20741) exited]
[New Thread 0x76563440 (LWP 24399)]
[Thread 0x76563440 (LWP 24399) exited]
[New Thread 0x76563440 (LWP 28060)]
[Thread 0x76563440 (LWP 28060) exited]
Thread 1 "pilinbpq" received signal SIGSEGV, Segmentation fault.
0x00129f98 in memicmp (a=0x0, b=0x265dc4 "TIMES", n=5) at /mnt/Source/bpq32/CommonSource/compatbits.c:72
72????? /mnt/Source/bpq32/CommonSource/compatbits.c: Bestand of map bestaat niet.
(gdb)
(gdb)
(gdb) bt
#0? 0x00129f98 in memicmp (a=0x0, b=0x265dc4 "TIMES", n=5) at /mnt/Source/bpq32/CommonSource/compatbits.c:72
#1? 0x000eda88 in ProcessBBSConnectScript (conn=0x3bd118 <Connections+5568>, Buffer=0x7efff3f8 "*** CONNECTED? ", len=15) at /mnt/Source/bpq32/CommonSource/BBSUtilities.c:8139
#2? 0x000f5eac in Connected (Stream=19) at /mnt/Source/bpq32/CommonSource/BBSUtilities.c:10496
#3? 0x001681e4 in PollStreams () at /mnt/Source/bpq32/CommonSource/LinBPQ.c:2041
#4? 0x001676c8 in main (argc=1, argv=0x7efff774) at /mnt/Source/bpq32/CommonSource/LinBPQ.c:1555
(gdb) quit
A debugging session is active.
??????? Inferior 1 [process 13376] will be killed.
Quit anyway? (y or n) y
73 Niels PD9Q
Op 25-10-2024 om 13:07 schreef John G8BPQ:
Can you try running under gdb?
Thanks,
John
On 25/10/2024 05:37, Niels PD9Q wrote:
Hi,
Lately I've been having? about every hour a segmentation fault with pilinbpq.
I don`t understand why.
Thanks.
73 Niels PD9Q
Oct 24 05:30:52 pi1lap bash[19835]: /home/pi/linbpq/linbpq.start: regel 11: 19838 Segmentatiefout???????? ./pilinbpq
Oct 24 05:30:52 pi1lap systemd[1]: linbpq.service: Main process exited, code=exited, status=139/n/a
Oct 24 05:30:52 pi1lap systemd[1]: linbpq.service: Failed with result 'exit-code'.
Oct 24 05:30:57 pi1lap systemd[1]: linbpq.service: Service RestartSec=5s expired, scheduling restart.
Oct 24 05:30:57 pi1lap systemd[1]: linbpq.service: Scheduled restart job, restart counter is at 23.
Oct 24 05:30:57 pi1lap systemd[1]: Stopped Linbpq Daemon.
Oct 24 05:30:57 pi1lap systemd[1]: Started Linbpq Daemon.
Oct 24 05:30:57 pi1lap bash[2341]: G8BPQ AX25 Packet Switch System Version 6.0.24.47 October 2024
pi@pi1lap:~/linbpq $ sudo gdb ./pilinbpq
GNU gdb (Raspbian 8.2.1-2) 8.2.1
Copyright (C) 2018 Free Software Foundation, Inc.
License GPLv3+: GNU GPL version 3 or later <>
This is free software: you are free to change and redistribute it.
There is NO WARRANTY, to the extent permitted by law.
Type "show copying" and "show warranty" for details.
This GDB was configured as "arm-linux-gnueabihf".
Type "show configuration" for configuration details.
For bug reporting instructions, please see:
<>.
Find the GDB manual and other documentation resources online at:
??? <>.
For help, type "help".
Type "apropos word" to search for commands related to "word"...
Reading symbols from ./pilinbpq...done.
(gdb) r
Starting program: /home/pi/linbpq/pilinbpq
[Thread debugging using libthread_db enabled]
Using host libthread_db library "/lib/arm-linux-gnueabihf/libthread_db.so.1".
G8BPQ AX25 Packet Switch System Version 6.0.24.47 October 2024
Copyright ? 2001-2024 John Wiseman G8BPQ
Current Directory is /home/pi/linbpq
Log Directory is /home/pi/linbpq
Making Directory /home/pi/linbpq/logs
Configuration file Preprocessor.
Using Configuration file /home/pi/linbpq/bpq32.cfg
Conversion (probably) successful
PORTS 0x2eb320 LINKS 0x2f2b30 DESTS 0x2f6640 ROUTES 0x303640 L4 0x306a40 BUFFERS 0x314380
[New Thread 0x76d64440 (LWP 30794)]
Initialising Port 01???? UZ7HO Host 44.137.31.76 Port 8101 Chan A
[New Thread 0x76563440 (LWP 30795)]
Initialising Port 02???? UZ7HO Host 44.137.31.76 Port 8101 Chan B
Initialising Port 03???? ARDOP Host 44.137.31.76 8515
[New Thread 0x75d62440 (LWP 30796)]
Initialising Port 04???? VARA Host 44.137.31.76 8300
[New Thread 0x75561440 (LWP 30797)]
Initialising Port 05???? UZ7HO Host 44.137.31.76 Port 8101 Chan C
Initialising Port 06???? ASYNC /dev/ttyUSB0 Chan A
[New Thread 0x74d60440 (LWP 30798)]
[New Thread 0x7455f440 (LWP 30799)]
Initialising Port 07???? AXIP
[New Thread 0x739ff440 (LWP 30800)]
Initialising Port 08???? Telnet Server
[New Thread 0x7455f440 (LWP 30801)]
[Thread 0x7455f440 (LWP 30799) exited]
Rig Control Enabled
[New Thread 0x731fe440 (LWP 30802)]
MQTT Enabled 0
[New Thread 0x729fd440 (LWP 30803)]
Starting Chat
Config File is /home/pi/linbpq/chatconfig.cfg
Chat Started
Starting Mail
Config File is /home/pi/linbpq/linmail.cfg
Config Processed
[Thread 0x739ff440 (LWP 30800) exited]
[New Thread 0x739ff440 (LWP 30808)]
[New Thread 0x721e7440 (LWP 30809)]
Mail Started
slave device: /dev/pts/0. symlink to /home/pi/fbbded created
TNC Emulator Init Complete
[New Thread 0x719e6440 (LWP 30810)]
[Thread 0x76563440 (LWP 30795) exited]
Connected to ARDOP TNC Port 3
Connected to VARA TNC Port 4
[New Thread 0x76563440 (LWP 744)]
[Thread 0x76563440 (LWP 744) exited]
[New Thread 0x76563440 (LWP 2172)]
[Thread 0x76563440 (LWP 2172) exited]
[New Thread 0x76563440 (LWP 5892)]
[Thread 0x76563440 (LWP 5892) exited]
[New Thread 0x76563440 (LWP 9581)]
[Thread 0x76563440 (LWP 9581) exited]
[New Thread 0x76563440 (LWP 13243)]
[Thread 0x76563440 (LWP 13243) exited]
Thread 1 "pilinbpq" received signal SIGSEGV, Segmentation fault.
0x00129f98 in memicmp (a=0x0, b=0x265dc4 "TIMES", n=5) at /mnt/Source/bpq32/CommonSource/compatbits.c:72
72????? /mnt/Source/bpq32/CommonSource/compatbits.c: Bestand of map bestaat niet.
(gdb) bt
#0? 0x00129f98 in memicmp (a=0x0, b=0x265dc4 "TIMES", n=5) at /mnt/Source/bpq32/CommonSource/compatbits.c:72
#1? 0x000eda88 in ProcessBBSConnectScript (conn=0x3bce60 <Connections+4872>, Buffer=0x7efff3f8 "*** CONNECTED? ", len=15) at /mnt/Source/bpq32/CommonSource/BBSUtilities.c:8139
#2? 0x000f5eac in Connected (Stream=18) at /mnt/Source/bpq32/CommonSource/BBSUtilities.c:10496
#3? 0x001681e4 in PollStreams () at /mnt/Source/bpq32/CommonSource/LinBPQ.c:2041
#4? 0x001676c8 in main (argc=1, argv=0x7efff774) at /mnt/Source/bpq32/CommonSource/LinBPQ.c:1555
(gdb)
|
Re: Kenwood TS-480 BPQ32 and VARA HF configuration help
So I have good news, IT'S WORKING!
?
Adding the command RIGCONTROL the option of DATAPTT that I found used for radios with internal sound card like the Yaesu FT-991A did the trick!
?
This is the working config for the Kenwood TS-480 with VARA HF and BPQ32:
?
;------------------------------------------- ?VARA HF PORT -------------------------------------
PORT
?ID=VARA
?PORTNUM=5
?DRIVER=VARA
?CONFIG
? ADDR 127.0.0.1 8303 PTT CAT PATH C:\VARA\VARA.exe
?RIGCONTROL
? COM3 19200 KENWOOD TS480 DATAPTT
? 10.1476,USB
?***
?BW500
ENDPORT
?
Thanks to all who helped in this journey on reviving an old HF radio to life!
?
Heber NP4JN
|
Re: Kenwood TS-480 BPQ32 and VARA HF configuration help
John
?
Is this documentation for radio with its own internal sound card:
?
This will switch the modulation source to Soundcard when a Sound Card modem sets PTT and return it to the AUX connector when PTT is dropped. With the ICOM rigs, if you want to select a different input when the sound card is not selected, you can add MIC, AUX or MICAUX after?PTT_SETS_INPUT. So if you are using the MIC connector for an SCS Tracker and the AUX for a PTC you could have
RIGCONTROL COM8 19200 ICOM IC7100 88 ?PTT_SETS_INPUT?MICAUX
Normally the radio should be set to accept input from the hardware TNC before running BPQ.
Some Kenwood radios use a different CAT command (TX1 instead of TX) to select USB input. If this is the case use the DATAPTT command. You may need to experiment to see if you need DATAPTT instead of or as well as PTT_SETS_INPUT with these radios.
?
If want to rise the RTS in the CAT port for the radio can I use the PTT_SETS_INPUT, can you provide an example?
?
Thanks
?
Heber NP4JN
|
Hi John,
Just the same output...
Thread 1 "pilinbpq" received signal SIGSEGV, Segmentation fault.
0x00129f98 in memicmp (a=0x0, b=0x265dc4 "TIMES", n=5) at /mnt/Source/bpq32/CommonSource/compatbits.c:72
72????? /mnt/Source/bpq32/CommonSource/compatbits.c: Bestand of map bestaat niet.
(gdb)
(gdb) (here are the enters)
(gdb) bt
#0? 0x00129f98 in memicmp (a=0x0, b=0x265dc4 "TIMES", n=5) at /mnt/Source/bpq32/CommonSource/compatbits.c:72
#1? 0x000eda88 in ProcessBBSConnectScript (conn=0x3bd118 <Connections+5568>, Buffer=0x7efff3f8 "*** CONNECTED? ", len=15) at /mnt/Source/bpq32/CommonSource/BBSUtilities.c:8139
#2? 0x000f5eac in Connected (Stream=19) at /mnt/Source/bpq32/CommonSource/BBSUtilities.c:10496
#3? 0x001681e4 in PollStreams () at /mnt/Source/bpq32/CommonSource/LinBPQ.c:2041
#4? 0x001676c8 in main (argc=1, argv=0x7efff774) at /mnt/Source/bpq32/CommonSource/LinBPQ.c:1555
(gdb)
I delete all the times in the forward scripts.....
For help, type "help".
Type "apropos word" to search for commands related to "word"...
Reading symbols from ./pilinbpq...done.
(gdb) r
Starting program: /home/pi/linbpq/pilinbpq
[Thread debugging using libthread_db enabled]
Using host libthread_db library "/lib/arm-linux-gnueabihf/libthread_db.so.1".
G8BPQ AX25 Packet Switch System Version 6.0.24.47 October 2024
Copyright ? 2001-2024 John Wiseman G8BPQ
Current Directory is /home/pi/linbpq
Log Directory is /home/pi/linbpq
Making Directory /home/pi/linbpq/logs
Configuration file Preprocessor.
Using Configuration file /home/pi/linbpq/bpq32.cfg
Conversion (probably) successful
PORTS 0x2eb320 LINKS 0x2f2b30 DESTS 0x2f6640 ROUTES 0x303640 L4 0x306a40 BUFFERS 0x314380
[New Thread 0x76d64440 (LWP 13385)]
Initialising Port 01???? UZ7HO Host 44.137.31.76 Port 8101 Chan A
[New Thread 0x76563440 (LWP 13386)]
Initialising Port 02???? UZ7HO Host 44.137.31.76 Port 8101 Chan B
Initialising Port 03???? ARDOP Host 44.137.31.76 8515
[New Thread 0x75d62440 (LWP 13387)]
Initialising Port 04???? VARA Host 44.137.31.76 8300
[New Thread 0x75561440 (LWP 13388)]
Initialising Port 05???? UZ7HO Host 44.137.31.76 Port 8101 Chan C
Initialising Port 06???? ASYNC /dev/ttyUSB0 Chan A
[New Thread 0x74d60440 (LWP 13389)]
[New Thread 0x7455f440 (LWP 13390)]
Initialising Port 07???? AXIP
[Thread 0x7455f440 (LWP 13390) exited]
[New Thread 0x7455f440 (LWP 13391)]
Initialising Port 08???? Telnet Server
[New Thread 0x739ff440 (LWP 13392)]
Rig Control Enabled
[New Thread 0x731fe440 (LWP 13393)]
MQTT Enabled 0
[New Thread 0x729fd440 (LWP 13394)]
Starting Chat
Config File is /home/pi/linbpq/chatconfig.cfg
Chat Started
Starting Mail
Config File is /home/pi/linbpq/linmail.cfg
Config Processed
[Thread 0x7455f440 (LWP 13391) exited]
[New Thread 0x7455f440 (LWP 13401)]
[New Thread 0x72184440 (LWP 13402)]
Mail Started
slave device: /dev/pts/0. symlink to /home/pi/fbbded created
TNC Emulator Init Complete
[New Thread 0x71983440 (LWP 13403)]
[Thread 0x76563440 (LWP 13386) exited]
Connected to ARDOP TNC Port 3
Connected to VARA TNC Port 4
[New Thread 0x76563440 (LWP 17063)]
[Thread 0x76563440 (LWP 17063) exited]
[New Thread 0x76563440 (LWP 20741)]
[Thread 0x76563440 (LWP 20741) exited]
[New Thread 0x76563440 (LWP 24399)]
[Thread 0x76563440 (LWP 24399) exited]
[New Thread 0x76563440 (LWP 28060)]
[Thread 0x76563440 (LWP 28060) exited]
Thread 1 "pilinbpq" received signal SIGSEGV, Segmentation fault.
0x00129f98 in memicmp (a=0x0, b=0x265dc4 "TIMES", n=5) at /mnt/Source/bpq32/CommonSource/compatbits.c:72
72????? /mnt/Source/bpq32/CommonSource/compatbits.c: Bestand of map bestaat niet.
(gdb)
(gdb)
(gdb) bt
#0? 0x00129f98 in memicmp (a=0x0, b=0x265dc4 "TIMES", n=5) at /mnt/Source/bpq32/CommonSource/compatbits.c:72
#1? 0x000eda88 in ProcessBBSConnectScript (conn=0x3bd118 <Connections+5568>, Buffer=0x7efff3f8 "*** CONNECTED? ", len=15) at /mnt/Source/bpq32/CommonSource/BBSUtilities.c:8139
#2? 0x000f5eac in Connected (Stream=19) at /mnt/Source/bpq32/CommonSource/BBSUtilities.c:10496
#3? 0x001681e4 in PollStreams () at /mnt/Source/bpq32/CommonSource/LinBPQ.c:2041
#4? 0x001676c8 in main (argc=1, argv=0x7efff774) at /mnt/Source/bpq32/CommonSource/LinBPQ.c:1555
(gdb) quit
A debugging session is active.
??????? Inferior 1 [process 13376] will be killed.
Quit anyway? (y or n) y
73 Niels PD9Q
Op 25-10-2024 om 13:07 schreef John G8BPQ:
toggle quoted message
Show quoted text
Can you try running under gdb?
Thanks,
John
On 25/10/2024 05:37, Niels PD9Q wrote:
Hi,
Lately I've been having? about every hour a segmentation fault with pilinbpq.
I don`t understand why.
Thanks.
73 Niels PD9Q
Oct 24 05:30:52 pi1lap bash[19835]: /home/pi/linbpq/linbpq.start: regel 11: 19838 Segmentatiefout???????? ./pilinbpq
Oct 24 05:30:52 pi1lap systemd[1]: linbpq.service: Main process exited, code=exited, status=139/n/a
Oct 24 05:30:52 pi1lap systemd[1]: linbpq.service: Failed with result 'exit-code'.
Oct 24 05:30:57 pi1lap systemd[1]: linbpq.service: Service RestartSec=5s expired, scheduling restart.
Oct 24 05:30:57 pi1lap systemd[1]: linbpq.service: Scheduled restart job, restart counter is at 23.
Oct 24 05:30:57 pi1lap systemd[1]: Stopped Linbpq Daemon.
Oct 24 05:30:57 pi1lap systemd[1]: Started Linbpq Daemon.
Oct 24 05:30:57 pi1lap bash[2341]: G8BPQ AX25 Packet Switch System Version 6.0.24.47 October 2024
pi@pi1lap:~/linbpq $ sudo gdb ./pilinbpq
GNU gdb (Raspbian 8.2.1-2) 8.2.1
Copyright (C) 2018 Free Software Foundation, Inc.
License GPLv3+: GNU GPL version 3 or later <>
This is free software: you are free to change and redistribute it.
There is NO WARRANTY, to the extent permitted by law.
Type "show copying" and "show warranty" for details.
This GDB was configured as "arm-linux-gnueabihf".
Type "show configuration" for configuration details.
For bug reporting instructions, please see:
<>.
Find the GDB manual and other documentation resources online at:
??? <>.
For help, type "help".
Type "apropos word" to search for commands related to "word"...
Reading symbols from ./pilinbpq...done.
(gdb) r
Starting program: /home/pi/linbpq/pilinbpq
[Thread debugging using libthread_db enabled]
Using host libthread_db library "/lib/arm-linux-gnueabihf/libthread_db.so.1".
G8BPQ AX25 Packet Switch System Version 6.0.24.47 October 2024
Copyright ? 2001-2024 John Wiseman G8BPQ
Current Directory is /home/pi/linbpq
Log Directory is /home/pi/linbpq
Making Directory /home/pi/linbpq/logs
Configuration file Preprocessor.
Using Configuration file /home/pi/linbpq/bpq32.cfg
Conversion (probably) successful
PORTS 0x2eb320 LINKS 0x2f2b30 DESTS 0x2f6640 ROUTES 0x303640 L4 0x306a40 BUFFERS 0x314380
[New Thread 0x76d64440 (LWP 30794)]
Initialising Port 01???? UZ7HO Host 44.137.31.76 Port 8101 Chan A
[New Thread 0x76563440 (LWP 30795)]
Initialising Port 02???? UZ7HO Host 44.137.31.76 Port 8101 Chan B
Initialising Port 03???? ARDOP Host 44.137.31.76 8515
[New Thread 0x75d62440 (LWP 30796)]
Initialising Port 04???? VARA Host 44.137.31.76 8300
[New Thread 0x75561440 (LWP 30797)]
Initialising Port 05???? UZ7HO Host 44.137.31.76 Port 8101 Chan C
Initialising Port 06???? ASYNC /dev/ttyUSB0 Chan A
[New Thread 0x74d60440 (LWP 30798)]
[New Thread 0x7455f440 (LWP 30799)]
Initialising Port 07???? AXIP
[New Thread 0x739ff440 (LWP 30800)]
Initialising Port 08???? Telnet Server
[New Thread 0x7455f440 (LWP 30801)]
[Thread 0x7455f440 (LWP 30799) exited]
Rig Control Enabled
[New Thread 0x731fe440 (LWP 30802)]
MQTT Enabled 0
[New Thread 0x729fd440 (LWP 30803)]
Starting Chat
Config File is /home/pi/linbpq/chatconfig.cfg
Chat Started
Starting Mail
Config File is /home/pi/linbpq/linmail.cfg
Config Processed
[Thread 0x739ff440 (LWP 30800) exited]
[New Thread 0x739ff440 (LWP 30808)]
[New Thread 0x721e7440 (LWP 30809)]
Mail Started
slave device: /dev/pts/0. symlink to /home/pi/fbbded created
TNC Emulator Init Complete
[New Thread 0x719e6440 (LWP 30810)]
[Thread 0x76563440 (LWP 30795) exited]
Connected to ARDOP TNC Port 3
Connected to VARA TNC Port 4
[New Thread 0x76563440 (LWP 744)]
[Thread 0x76563440 (LWP 744) exited]
[New Thread 0x76563440 (LWP 2172)]
[Thread 0x76563440 (LWP 2172) exited]
[New Thread 0x76563440 (LWP 5892)]
[Thread 0x76563440 (LWP 5892) exited]
[New Thread 0x76563440 (LWP 9581)]
[Thread 0x76563440 (LWP 9581) exited]
[New Thread 0x76563440 (LWP 13243)]
[Thread 0x76563440 (LWP 13243) exited]
Thread 1 "pilinbpq" received signal SIGSEGV, Segmentation fault.
0x00129f98 in memicmp (a=0x0, b=0x265dc4 "TIMES", n=5) at /mnt/Source/bpq32/CommonSource/compatbits.c:72
72????? /mnt/Source/bpq32/CommonSource/compatbits.c: Bestand of map bestaat niet.
(gdb) bt
#0? 0x00129f98 in memicmp (a=0x0, b=0x265dc4 "TIMES", n=5) at /mnt/Source/bpq32/CommonSource/compatbits.c:72
#1? 0x000eda88 in ProcessBBSConnectScript (conn=0x3bce60 <Connections+4872>, Buffer=0x7efff3f8 "*** CONNECTED? ", len=15) at /mnt/Source/bpq32/CommonSource/BBSUtilities.c:8139
#2? 0x000f5eac in Connected (Stream=18) at /mnt/Source/bpq32/CommonSource/BBSUtilities.c:10496
#3? 0x001681e4 in PollStreams () at /mnt/Source/bpq32/CommonSource/LinBPQ.c:2041
#4? 0x001676c8 in main (argc=1, argv=0x7efff774) at /mnt/Source/bpq32/CommonSource/LinBPQ.c:1555
(gdb)
|
Re: Linbpq, Winlink Express, and Kenwood D710 won't connect
This turned out to be 1D10T error because of a duplicate callsign and SSID.
I had tested the RMS feature for our permanent node while it was at my QTH and I had internet. When I moved it to our tower, I forgot to comment out the Application for the RMS (APPLICATION 3,RMS,C 1 CMS,K9TSM-10,,0) because we don¡¯t have internet there yet. When I put up a temporary node at a separate location and used the same call and SSID, I had identical calls in the same system. Once that was taken care of, the Kenwood (and others) worked flawlessly.
?
Thanks to all that tried to help. But as the old saying goes, ¡°You can¡¯t fix stupid, not even with duct tape.¡±
?
Dave Menges
|
Re: Kenwood TS-480 BPQ32 and VARA HF configuration help
Jouko
?
I did had performed your recommendations and also in the radio the MIC data volume has been set to 9, the maximum.
?
I have been reading the radio manual and what I understood is that the RTS needs to be high on the DB9 CAT port so the radio switches to the data port MIC.
?
In WSTJ-X for it to work properly that's a setting that needs to be activated as the screen shoot provided, is there a command for RIGCONTROL to achieve this?
?
I was reading BPQ32 documentation it states that RIGCONTROL commands are legacy and it will continue to be active for backward combability but I cant find anywhere all the available commands on the documentation.
?
|
Mauro Veiga