Re: Setting myself (SYSOP) up as a user in mail mgmt
Start here?
3rd link is bbs section
Herbert KD5PQJ?
|
code=exited, status=127 error
After running the update and a reboot I keep getting the below error message.? What changed with the new update causing the error? ? pi@raspberrypi:~/linbpq $ sudo systemctl status? bpq ¡ñ bpq.service - BPQ ?? Loaded: loaded (/lib/systemd/system/bpq.service; enabled; vendor preset: enab ?? Active: failed (Result: exit-code) since Thu 2023-05-25 17:19:10 CDT; 3s ago ? Process: 996 ExecStart=/home/pi/linbpq/linbpq (code=exited, status=127) Main PID: 996 (code=exited, status=127) ? May 25 17:19:10 raspberrypi systemd[1]: bpq.service: Service RestartSec=100ms ex May 25 17:19:10 raspberrypi systemd[1]: bpq.service: Scheduled restart job, rest May 25 17:19:10 raspberrypi systemd[1]: Stopped BPQ. May 25 17:19:10 raspberrypi systemd[1]: bpq.service: Start request repeated too May 25 17:19:10 raspberrypi systemd[1]: bpq.service: Failed with result 'exit-co May 25 17:19:10 raspberrypi systemd[1]: Failed to start BPQ. ? Thanks, Jeff N9JXN
|
Thanks John,
I installed qmake6. Then downloaded the QtTermSource.zip from your
site. I extracted then ran qmake6 and got this error:
ny3j@ny3j-Studio-XPS-435T-9000:~/Downloads/QtTermSource$ sudo qmake6
[sudo] password for ny3j:??????? ?
Project ERROR: Unknown module(s) in QT: core gui network widgets
ny3j@ny3j-Studio-XPS-435T-9000:~/Downloads/QtTermSource$
Ron NY3J
On 5/25/23 09:42, John G8BPQ wrote:
toggle quoted message
Show quoted text
Latest is 0.65. I've uploaded an Intel 64 bit build to my beta
area,
73,
John
On 25/05/2023 13:59, Ron NY3J via
groups.io wrote:
Hi John,
It's QtTermTCP Version 0.0.0.60 64 bit version. I couldn't find
anything newer.
Ron NY3J
On 5/25/23 08:53, John G8BPQ wrote:
Which version of QtTerm are you running?
Until recently there was a bug where if you ran it in single
window mode with a combined terminal and monitor screen with
AGW enabled the AGW monitor session would grab the whole
window and connect was greyed out. Fixes are to upgrade or run
in multi window (MDI or Tabbed) mode.
73,
John
On 25/05/2023 11:52, Ron NY3J via
groups.io wrote:
Hi Glenn,
Thanks for the assistance. So AGW does show connected in the
right corner but the Connect tab on the top is greyed our.
But I have an update. I tried Kiss and it works okay now.
Another but. When I connect with KC3SMW-7 via W3SK I connect
but immediately send a DM with KC3SMW-7 continuing to send
me the welcome instructions.
Ah, it's nice to have local tech support :-) Good talking to
you on the repeater Glenn. So I'm going to try adding -1 to
my call and maybe changing the local port in case of
conflicts to see if that helps with the connect to KC3SMW-7.
Thanks again Glenn and don't work too hard today.
73, Ron NY3J
On 5/25/23 06:17, N3MEL - Glenn
wrote:
Not sure what mean, Nothing Happens? AGW is showing
in the Connect tab? If it is in the lower right corner
there a
box that should say AGW Connected or not.
I can meet you the CCAR repeater in about 10 minutes or
tonight
after nets??
N3MEL
|
Re: Return to Node instead of disconnect
|
Re: linbpq reconnection bug / misconfiguration / misunderstanding ?
Sorry, no. It slipped my mind. I'll see if I can recreate it.
73,
John
On 25/05/2023 16:14, Tom M0LTE wrote:
toggle quoted message
Show quoted text
Hey John, did you manage to look into this at all please?
Best wishes
Tom
|
Setting myself (SYSOP) up as a user in mail mgmt
Hello all,
I am very new to linbpq32 so forgive me in advance
I cant find this info anywhere but do I add myself into the mail forwarding? I have seen examples wherer people have added themselves and connected to themselves in the script. I tried that with hesitation, and of course piles of errors in the logs, so I assume that I remove myself from this section?...
|
Re: linbpq reconnection bug / misconfiguration / misunderstanding ?
Hey John, did you manage to look into this at all please?
Best wishes
Tom
|
Latest is 0.65. I've uploaded an Intel 64 bit build to my beta area,
73,
John
On 25/05/2023 13:59, Ron NY3J via
groups.io wrote:
toggle quoted message
Show quoted text
Hi John,
It's QtTermTCP Version 0.0.0.60 64 bit version. I couldn't find
anything newer.
Ron NY3J
On 5/25/23 08:53, John G8BPQ wrote:
Which version of QtTerm are you running?
Until recently there was a bug where if you ran it in single
window mode with a combined terminal and monitor screen with AGW
enabled the AGW monitor session would grab the whole window and
connect was greyed out. Fixes are to upgrade or run in multi
window (MDI or Tabbed) mode.
73,
John
On 25/05/2023 11:52, Ron NY3J via
groups.io wrote:
Hi Glenn,
Thanks for the assistance. So AGW does show connected in the
right corner but the Connect tab on the top is greyed our.
But I have an update. I tried Kiss and it works okay now.
Another but. When I connect with KC3SMW-7 via W3SK I connect
but immediately send a DM with KC3SMW-7 continuing to send me
the welcome instructions.
Ah, it's nice to have local tech support :-) Good talking to
you on the repeater Glenn. So I'm going to try adding -1 to my
call and maybe changing the local port in case of conflicts to
see if that helps with the connect to KC3SMW-7.
Thanks again Glenn and don't work too hard today.
73, Ron NY3J
On 5/25/23 06:17, N3MEL - Glenn
wrote:
Not sure what mean, Nothing Happens? AGW is showing
in the Connect tab? If it is in the lower right corner
there a
box that should say AGW Connected or not.
I can meet you the CCAR repeater in about 10 minutes or
tonight
after nets??
N3MEL
|
I've added a option to run a set of node commands when a port disconnects. This only works with ports that need an ATTACH before use (ie not KISS ports).
The configuration command format is something like this, and goes after the CONFIG command.
?DisconnectScript RADIO 11 14.102 USB|uz7ho 11 modem AFSK AX.25 1200bd|uz7ho 11 freq 2000
ie Node commands separated by | characters. Note the script runs after the port has detached so you can only use Node commands, not modem commands.
So this can be used to reset the modem or centre frequency on QtSoundModem I've added node level versions of the UZ7HO Modem and Freq commands - see the above example for format.
73,
John
|
Hi John,
It's QtTermTCP Version 0.0.0.60 64 bit version. I couldn't find
anything newer.
Ron NY3J
On 5/25/23 08:53, John G8BPQ wrote:
toggle quoted message
Show quoted text
Which version of QtTerm are you running?
Until recently there was a bug where if you ran it in single
window mode with a combined terminal and monitor screen with AGW
enabled the AGW monitor session would grab the whole window and
connect was greyed out. Fixes are to upgrade or run in multi
window (MDI or Tabbed) mode.
73,
John
On 25/05/2023 11:52, Ron NY3J via
groups.io wrote:
Hi Glenn,
Thanks for the assistance. So AGW does show connected in the
right corner but the Connect tab on the top is greyed our.
But I have an update. I tried Kiss and it works okay now.
Another but. When I connect with KC3SMW-7 via W3SK I connect but
immediately send a DM with KC3SMW-7 continuing to send me the
welcome instructions.
Ah, it's nice to have local tech support :-) Good talking to you
on the repeater Glenn. So I'm going to try adding -1 to my call
and maybe changing the local port in case of conflicts to see if
that helps with the connect to KC3SMW-7.
Thanks again Glenn and don't work too hard today.
73, Ron NY3J
On 5/25/23 06:17, N3MEL - Glenn
wrote:
Not sure what mean, Nothing Happens? AGW is showing
in the Connect tab? If it is in the lower right corner there
a
box that should say AGW Connected or not.
I can meet you the CCAR repeater in about 10 minutes or
tonight
after nets??
N3MEL
|
Which version of QtTerm are you running?
Until recently there was a bug where if you ran it in single window
mode with a combined terminal and monitor screen with AGW enabled
the AGW monitor session would grab the whole window and connect was
greyed out. Fixes are to upgrade or run in multi window (MDI or
Tabbed) mode.
73,
John
On 25/05/2023 11:52, Ron NY3J via
groups.io wrote:
toggle quoted message
Show quoted text
Hi Glenn,
Thanks for the assistance. So AGW does show connected in the right
corner but the Connect tab on the top is greyed our.
But I have an update. I tried Kiss and it works okay now.
Another but. When I connect with KC3SMW-7 via W3SK I connect but
immediately send a DM with KC3SMW-7 continuing to send me the
welcome instructions.
Ah, it's nice to have local tech support :-) Good talking to you
on the repeater Glenn. So I'm going to try adding -1 to my call
and maybe changing the local port in case of conflicts to see if
that helps with the connect to KC3SMW-7.
Thanks again Glenn and don't work too hard today.
73, Ron NY3J
On 5/25/23 06:17, N3MEL - Glenn
wrote:
Not sure what mean, Nothing Happens? AGW is showing
in the Connect tab? If it is in the lower right corner there a
box that should say AGW Connected or not.
I can meet you the CCAR repeater in about 10 minutes or
tonight
after nets??
N3MEL
|
Update: so I just got Linpac working and I was able to connect to
KC3SMW-7 via W3SK. I'll keep trying things and get back with
results.
73, Ron NY3J
On 5/25/23 07:11, Ron NY3J via
groups.io wrote:
toggle quoted message
Show quoted text
So I tried adding -1 to my call without success. Also tried
changing the Kiss port to 8010 without success. Below is the
monitor window when I connect to KC3SMW-7. You can see where I
send the immediate DM.
I'm in the process of trying Linpac to see if that connects.
10:58:38T NY3J-1>KC3SMW-7,W3SK <SABM C P>
10:58:41R NY3J-1>KC3SMW-7,W3SK* <SABM C P>
10:58:45R KC3SMW-7>NY3J-1,W3SK* <UA R F>
10:58:45T NY3J-1>KC3SMW-7,W3SK <DM R F>
10:58:46T NY3J-1>KC3SMW-7,W3SK <SABM C P>
10:58:46R KC3SMW-7>NY3J-1,W3SK* <I C P R0 S0>
Welcome to the chengmanian Node.? A Bucks County Node available to
all amateur operators.
BBS CHAT RMS CONNECT BYE INFO NODES PORTS ROUTES USERS MHEARD
Type ? for list of available commands.
10:58:46T NY3J-1>KC3SMW-7,W3SK <DM R F>
10:58:50R NY3J-1>KC3SMW-7,W3SK* <DM R F>
10:58:50R NY3J-1>KC3SMW-7,W3SK* <SABM C P>
10:58:50R NY3J-1>KC3SMW-7,W3SK* <DM R F>
10:58:54R KC3SMW-7>NY3J-1,W3SK* <UA R F>
10:58:54T NY3J-1>KC3SMW-7,W3SK <DM R F>
10:58:54T NY3J-1>KC3SMW-7,W3SK <SABM C P>
10:58:55R KC3SMW-7>NY3J-1,W3SK* <I C P R0 S0>
Welcome to the chengmanian Node.? A Bucks County Node available to
all amateur operators.
BBS CHAT RMS CONNECT BYE INFO NODES PORTS ROUTES USERS MHEARD
Type ? for list of available commands.
10:58:55T NY3J-1>KC3SMW-7,W3SK <DM R F>
10:58:56T NY3J-1>KC3SMW-7,W3SK <DISC C P>
73, Ron NY3J
On 5/25/23 06:52, Ron NY3J via
groups.io wrote:
Hi Glenn,
Thanks for the assistance. So AGW does show connected in the
right corner but the Connect tab on the top is greyed our.
But I have an update. I tried Kiss and it works okay now.
Another but. When I connect with KC3SMW-7 via W3SK I connect but
immediately send a DM with KC3SMW-7 continuing to send me the
welcome instructions.
Ah, it's nice to have local tech support :-) Good talking to you
on the repeater Glenn. So I'm going to try adding -1 to my call
and maybe changing the local port in case of conflicts to see if
that helps with the connect to KC3SMW-7.
Thanks again Glenn and don't work too hard today.
73, Ron NY3J
On 5/25/23 06:17, N3MEL - Glenn
wrote:
Not sure what mean, Nothing Happens? AGW is showing
in the Connect tab? If it is in the lower right corner there
a
box that should say AGW Connected or not.
I can meet you the CCAR repeater in about 10 minutes or
tonight
after nets??
N3MEL
|
So I tried adding -1 to my call without success. Also tried changing
the Kiss port to 8010 without success. Below is the monitor window
when I connect to KC3SMW-7. You can see where I send the immediate
DM.
I'm in the process of trying Linpac to see if that connects.
10:58:38T NY3J-1>KC3SMW-7,W3SK <SABM C P>
10:58:41R NY3J-1>KC3SMW-7,W3SK* <SABM C P>
10:58:45R KC3SMW-7>NY3J-1,W3SK* <UA R F>
10:58:45T NY3J-1>KC3SMW-7,W3SK <DM R F>
10:58:46T NY3J-1>KC3SMW-7,W3SK <SABM C P>
10:58:46R KC3SMW-7>NY3J-1,W3SK* <I C P R0 S0>
Welcome to the chengmanian Node.? A Bucks County Node available to
all amateur operators.
BBS CHAT RMS CONNECT BYE INFO NODES PORTS ROUTES USERS MHEARD
Type ? for list of available commands.
10:58:46T NY3J-1>KC3SMW-7,W3SK <DM R F>
10:58:50R NY3J-1>KC3SMW-7,W3SK* <DM R F>
10:58:50R NY3J-1>KC3SMW-7,W3SK* <SABM C P>
10:58:50R NY3J-1>KC3SMW-7,W3SK* <DM R F>
10:58:54R KC3SMW-7>NY3J-1,W3SK* <UA R F>
10:58:54T NY3J-1>KC3SMW-7,W3SK <DM R F>
10:58:54T NY3J-1>KC3SMW-7,W3SK <SABM C P>
10:58:55R KC3SMW-7>NY3J-1,W3SK* <I C P R0 S0>
Welcome to the chengmanian Node.? A Bucks County Node available to
all amateur operators.
BBS CHAT RMS CONNECT BYE INFO NODES PORTS ROUTES USERS MHEARD
Type ? for list of available commands.
10:58:55T NY3J-1>KC3SMW-7,W3SK <DM R F>
10:58:56T NY3J-1>KC3SMW-7,W3SK <DISC C P>
73, Ron NY3J
On 5/25/23 06:52, Ron NY3J via
groups.io wrote:
toggle quoted message
Show quoted text
Hi Glenn,
Thanks for the assistance. So AGW does show connected in the right
corner but the Connect tab on the top is greyed our.
But I have an update. I tried Kiss and it works okay now.
Another but. When I connect with KC3SMW-7 via W3SK I connect but
immediately send a DM with KC3SMW-7 continuing to send me the
welcome instructions.
Ah, it's nice to have local tech support :-) Good talking to you
on the repeater Glenn. So I'm going to try adding -1 to my call
and maybe changing the local port in case of conflicts to see if
that helps with the connect to KC3SMW-7.
Thanks again Glenn and don't work too hard today.
73, Ron NY3J
On 5/25/23 06:17, N3MEL - Glenn
wrote:
Not sure what mean, Nothing Happens? AGW is showing
in the Connect tab? If it is in the lower right corner there a
box that should say AGW Connected or not.
I can meet you the CCAR repeater in about 10 minutes or
tonight
after nets??
N3MEL
|
Hi Glenn,
Thanks for the assistance. So AGW does show connected in the right
corner but the Connect tab on the top is greyed our.
But I have an update. I tried Kiss and it works okay now.
Another but. When I connect with KC3SMW-7 via W3SK I connect but
immediately send a DM with KC3SMW-7 continuing to send me the
welcome instructions.
Ah, it's nice to have local tech support :-) Good talking to you on
the repeater Glenn. So I'm going to try adding -1 to my call and
maybe changing the local port in case of conflicts to see if that
helps with the connect to KC3SMW-7.
Thanks again Glenn and don't work too hard today.
73, Ron NY3J
On 5/25/23 06:17, N3MEL - Glenn wrote:
toggle quoted message
Show quoted text
Not sure what mean, Nothing Happens? AGW is showing
in the Connect tab? If it is in the lower right corner there a
box that should say AGW Connected or not.
I can meet you the CCAR repeater in about 10 minutes or tonight
after nets??
N3MEL
|
Not sure what mean, Nothing Happens? AGW is showing
in the Connect tab? If it is in the lower right corner there a
box that should say AGW Connected or not.
I can meet you the CCAR repeater in about 10 minutes or tonight
after nets??
N3MEL
|
Re: QtSoundModem MEMAX25?
As the latest QtSM supports IL2P I've added a tag of the mode the packet was received in.? Values are AX25, FX25 (packet corrected by fec, not just sent using FX25) or IL2P.
MEM is added if the packet has been corrected by Memory ARQ (where sound samples from retries are combined to form a good packet).
# Indicates this decoder was corrected by MEM ARQ. # Has always been there, but adding the MEM tag is new.
The 0 is part of an experimental system to measure that actual centre frequency of the received packet. I'm a bit surprised to see zero - it is normally close to the actual centre frequency.
73,
John
toggle quoted message
Show quoted text
On 24/05/2023 17:09, Rich Sahlender wrote: Using QtSoundModem 0.0.0.64 source compiled for x86_64 I see the following for a 40m port:
1:Fm KT4WO-1 To KB9PVH-6 <RR C? P R0>[15:50:43R][--+--][AX25 0]
1:Fm KT4WO-1 To KB9PVH-6 <RR C? P R0>[15:50:49R][--#--][MEMAX25 0]
1:Fm KT4WO-1 To KB9PVH-6 <RR C? P R0>[15:50:55R][--+--][AX25 0]
1:Fm KT4WO-1 To KB9PVH-6 <RR C? P R0>[15:51:01R][--#--][MEMAX25 0]
The obvious difference is the # vs + which may well explain things but I plumb forget what the difference is at the moment without digging into the source. What does MEMAX25 indicate?
FWIW this instance of qtsm is configured with bit recovery and il2p set to NONE and FX25 set to RX+TX.
Tnx es 73 de Rich WA3WLH
|
Re: Return to Node instead of disconnect
Connects to CMS are processed different to normal application
connects and Stay isn't handled, but it should work for connects to
other applications that use an alias.
You can't use S with normal application connects, but BPQ BBS has a
command to return to node (Node).
73,
John
On 23/05/2023 14:10, Doug VE1LG via
groups.io wrote:
toggle quoted message
Show quoted text
I know if I connect from my node to another using S then when I
"bye" from that second node I am returned to the first.? But I
can't seem to get this working for applications.? In my
bpq32.cfg I have the following from CMS (which is otherwise
working well):
APPLICATION 2,RMS,C 10
CMS S,VE1LG-10,KINGRMS,255
Yet when I issue bye from CMS it disconnects.? This is in
QtTermTCP via telnet to my node, not over RF, if that makes
a difference.
Also, how would I add S to the BBS when it doesn't
use C as so:
APPLICATION
1,BBS,,VE1LG-1,KINGBB,255
Cheers,
Doug
|
Re: anyone using Python to write external apps for BPQ?
I know this thread is old, but I just saw your post Brad. Thanks for sharing your work. I've got your space wx app running and I think it is fantastic.
73,
Doug VE1LG
|
Re: QtSoundModem MEMAX25?
That entire [segment] is new in the .64 build.
MEM is a hit match on the MEMory ARQ which when a repeated packet that is corrupted by noise, it is confident that it decoded a good packet using the error correction memory cache. I might not be 100% on this but its what I have learned so far.
73
Red
|
Hi All,
I have Linux Mint 22.1 64 bit and installed QTTermTCP 64 bit version that I plan to run with Direwolf.
When I click connect nothing happens. I do have AGW configured.
73, Ron NY3J
|
Ron NY3J
Doug VE1LG
N3MEL - Glenn
Red R. R. Tuby (PE1RRR)