John
Sent you a couple of emails direct with a couple of problems in Version 6.0.23.4
No worries Guys I think this may be a isolated case related with the AMPR Network.
Mike Melnik-N9PMO
BPQ32 Group Moderator
|
IPGATEWAY, 44ENCAP and actual AMPRGW on remote wireguard host
Hi,
I am struggling to find a way to make linbpq work with IPGATEWAY.??? OS is Debian 10, kernel 4.19.0-16-686-pae patched with Marius' YO2LOJ AX25 "else" patch for linux ax25.
My IPIP endpoint is a linux box on the far end of a wireguard link and uses the main linux gw ip 44.76.0.193 as the routable wireguard ip and terminates to the linux host at 44.76.0.205
BPQ runs on top that linux box at 44.76.0.205, but I want to use 44.76.0.195 as the IPIP/amprnet ip on BPQ in IPGATEWAY.?
I cannot figure out the correct BPQ config to make it talk to linux routing table and sort the rest out.? The routes are all in linux on the device bpq runs on but since TAP wont talk to interface wg0 because it is not tappable, not sure what my option is.
Over the wire in a packet dump it should look like
44.76.0.205 -> 44.76.0.193 proto ipip
44.76.0.195 -> ANYTUNNELED_44_IP
vice versa on the return path.? Regardless IPIP packets need to get to 44.76.0.193 via linux kernel routing to work in wireguard.
I do this this way because at the linux amprnet gw its easily controls ingress to only allow amprnet ips to access my amprnet ips from a centralized firewall at the router gw.
I hope that makes sense, but perhaps I am not clear.?? Let me know if you need anything further.
IPGATEWAY
ADAPTER enp1s0
44ENCAP 192.168.200.205 ; or I can use 44.76.0.193 as the encap endpoint or an unused lan IP.? None seemed to do much usefulness.
IPADDR 44.76.0.195
IPNETMASK 255.255.255.255
NODEFAULTROUTE
IPPORTS 1
ROUTE 0.0.0.0/0 192.168.200.205
;ROUTE 44.0.0.0/9 44.76.0.193 T? # dont use these, they override linux routes present from wireguard and tie them to LinBPQTAP interface, not desired - Using kernel routing is desired here, I use wireguard and freerrp's bgp to manage route tables and they write to linux routes.
;ROUTE 44.128.0.0/10 44.76.0.193 T
***
I've tried various route's above but removed them as they werent helpful,
Is there any hope or am I completely out there due to my unique situation?
Thanks for reading this.
73 Kayne - n9seo
|
Richard Hendricks - KE0GB
|
I've seen this occasionally, but so far haven't managed to find
where it is coming from. I'll keep looking.
73,
John
On 11/07/2022 20:32, Richard Hendricks
- KE0GB wrote:
toggle quoted message
Show quoted text
>From time-to-time, I see some nodes exhibiting what i call the
"255 error".? ?I lose
without notice, an AXIP link to some of my partners, and see the
link from my node
to my partner's node up, but on their end, I see this:
no
ke0gb-7
QINOD:KQ0I-7}
Routes to: COSCO:KE0GB-7
192
255 1 KE0GB-7? ? ? ? ?<-------? 255 in the second place
144
5 1 KM8V-7
Notice the "255" figure in the obsolescence place.? I've seen
this on several nodes
going back several
versions.? I've asked the partner to shut down their BPQ32,
remove the BPQNodes.dat file, and reboot.? This, of course, is a
workaround,
but I'm wondering how this develops in the first place.
I recently started seeing W0ARP's BBS using his fallback routing
over 2m
and checked his AXIP routing to AC0VC's BBS:
?no ac0vc-7
PHYLNS:W0ARP-7}
Routes to: VCBPQ:AC0VC-7
192
255 1 AC0VC-7? ? ?<-----again, that 255 figure the
obsolescence
144
5 1 N0HI-7
How is this 255 figure creeping into our nodes?
73 - Rick
KE0GB
|
On Thu, Jul 14, 2022 at 10:06 AM, Joey N4QMI wrote:
Hey Red, I only tried a couple for testing purposes only and I removed them. I was able to add N3HYM with no problem but W4GON gives the error.
BPQAXIP - Bad config record MAP W4GON-7 10093 B
Joel (W4GON) and I are corresponding by email as well trying to find the problem.?
Joey
Hi Joey No worries, yeah some nodes do autoaddmap - I have a backup node that provides that, if you¡¯d like to link up with mine I¡¯ve got all the info posted here: ?password is ¡®matrix¡¯ (without quotes). Glad to hear you got the UDP port info sorted with John, its easy to miss! 73 Red
|
On Thu, Jul 14, 2022 at 12:18 PM, Joey N4QMI wrote:
That was the problem John, but is weird is that N5MDT doesn't use UDP before 10094 and it works.. I tried his with UDP in it and it gave an error.. But it works so problem solved! Thanks!
We couldn't get the UDP working. We are connected via a TCP connection. Mark, N5MDT
|
That was the problem John, but is weird is that N5MDT doesn't use UDP before 10094 and it works.. I tried his with UDP in it and it gave an error.. But it works so problem solved! Thanks!
|
Hey Red, I only tried a couple for testing purposes only and I removed them. I was able to add N3HYM with no problem but W4GON gives the error.
BPQAXIP - Bad config record MAP W4GON-7 10093 B
Joel (W4GON) and I are corresponding by email as well trying to find the problem.?
Joey
|
Joey,
You need UDP before 10093
73,
John
On 14/07/2022 17:17, Joey N4QMI wrote:
toggle quoted message
Show quoted text
Hey John, sorry to mention that in the original message. Here is
the error messages I get..
BPQAXIP - Bad config record MAP W4GON-7 10093 B
BPQAXIP - Bad config record MAP KB9SOZ-7 10093 B
?
And a couple of others.. There are three that are working
just fine including w9gm-7.
|
Hey John, sorry to mention that in the original message. Here is the error messages I get..
BPQAXIP - Bad config record MAP W4GON-7 10093 B
BPQAXIP - Bad config record MAP KB9SOZ-7 10093 B
?
And a couple of others.. There are three that are working just fine including w9gm-7.
|
Hey Mark, I had to restart computer. Sorry about that. Problem existed before computer locked went offline and problem is still there.
Joey
|
Re: Providing RMS via AREDN from LinBPQ
If you could answer a few questions it should help me understand exactly what you are trying to do.
Are you using Winlink Express as your client? If not, what client is being used?
Is your Winlink gateway on the same machine as your BBS, or somewhere else on the Mesh?
Do your clients connect directly via the Mesh to your BBS, or are there other BBS's on the Mesh that they connect to, then forward messages to the Winlink gateway?
Do you want all messages between clients to be routed via Winlink?
73,
John
toggle quoted message
Show quoted text
On 14/07/2022 15:36, Heber Soto wrote: My question was to broad, I do know on how to configure the Winlink client and the AREDN node on how to make the service available.
We were doing test yesterday and messages where being accepted by the BBS and routing them through our KP4DOG BPQ network as a BBS message.
Do we have to change something on the BPQ config to accept traffic via port 8772 or it will accept it natively to relay to the Winlink's CMS?
Or does de BBS respond to the Winlink client and sends the messages as a BBS message?
Or can both operation occurred?
Gracias 73,
Heber
NP4JN
On 7/14/2022 3:33 AM, John G8BPQ wrote:
Provided that somewhere on the ARDEN network there is a node with Internet to access an RMS Server then yes.
73, John
On 14/07/2022 03:15, Heber Soto wrote:
Hello
Can a LinBPQ connected to a AREDN node provide a RMS service via AREDN?
|
Re: Providing RMS via AREDN from LinBPQ
My question was to broad, I do know on how to configure the Winlink client and the AREDN node on how to make the service available.
We were doing test yesterday and messages where being accepted by the BBS and routing them through our KP4DOG BPQ network as a BBS message.
Do we have to change something on the BPQ config to accept traffic via port 8772 or it will accept it natively to relay to the Winlink's CMS?
Or does de BBS respond to the Winlink client and sends the messages as a BBS message?
Or can both operation occurred?
Gracias 73,
Heber
NP4JN
toggle quoted message
Show quoted text
On 7/14/2022 3:33 AM, John G8BPQ wrote: Provided that somewhere on the ARDEN network there is a node with Internet to access an RMS Server then yes.
73, John
On 14/07/2022 03:15, Heber Soto wrote:
Hello
Can a LinBPQ connected to a AREDN node provide a RMS service via AREDN?
--
Gracias 73,
Heber
NP4JN
|
Joey, according to my info your node has been offline for the last 7 hours. Are you sure it is starting? Look for network issues and error messages and get the node back online first.
Cheers,
Mark
|
Re: direwolf, signalink, and bpq32 on linux
Christopher Molnar, did you get it sorted???
|
Re: Providing RMS via AREDN from LinBPQ
Absolutely.?
Open Winlink Express
Open a Telnet Post Office Session
Click Add Server
Click UPDATE AREDN MESH NODE LIST
This only works if your node is connected to the mesh network properly.
Mark
|
On 7/14/22 06:33, John G8BPQ wrote: The resolver converts host names to pi addreses. Can be viewed in the Windows GUI or via the node command AXR
<snip> 73,
John
On 14/07/2022 10:54, Chuck Gelm wrote:
On 7/14/22 00:44, Joey N4QMI wrote:
Nothing shows up in my AXIP port resolver All:
What is an 'AXIP port resolver' ?
3s, Chuck Super cool! Works fine in (pi)linbpq. Thanks.
|
Re: Providing RMS via AREDN from LinBPQ
On 7/13/22 22:15, Heber Soto wrote: Hello
Can a LinBPQ connected to a AREDN node provide a RMS service via AREDN?
--
Gracias 73,
Heber
NP4JN Here is another link:
|
The resolver converts host names to pi addreses. Can be viewed in
the Windows GUI or via the node command AXR
axr 1
BPQ:G8BPQ-2} AXIP Resolver info for Port 1
GM8BPQ-11? = 192.168.1.199 0 = 192.168.1.199
GM8BPQ-7?? = 192.168.1.35 10093 = 192.168.1.35 B
AE5E-14??? = DXSPOTS.COM 10093 = 216.172.112.208 B C
G8BPQ-9??? = 192.168.1.44 10092 = 192.168.1.44 B
N9PMO-2??? = n9pmo.no-ip.org 10093 = 70.94.252.87 B
N9LYA????? = w9bbs.no-ip.org 10093 = 63.142.97.107 B
73,
John
On 14/07/2022 10:54, Chuck Gelm wrote:
toggle quoted message
Show quoted text
On
7/14/22 00:44, Joey N4QMI wrote:
Nothing shows up in my AXIP port resolver
All:
What is an 'AXIP port resolver' ?
3s, Chuck
|
Re: Providing RMS via AREDN from LinBPQ
On 7/13/22 22:15, Heber Soto wrote: Hello
Can a LinBPQ connected to a AREDN node provide a RMS service via AREDN?
--
Gracias 73,
Heber
NP4JN Attached is a 1 minute video segment from a video by Orv Beach w6bi. (2.5 MBytes) In addition to 'auto-discovery' by Winlink Express... My 'Winlink Post Office' on my AREDN network server only requires BBS registration and a web browser to send/receive Winlink email. This is configurable with the BPQ32 application. 3s, Chuck
|
Red R. R. Tuby (PE1RRR)
Joshua KJ7LVZ