开云体育

Hi, Jim: Valid range values are, at least, 300 to 9999, as I have used them without seeing a failure. I have 'Send new messages without waiting for poll timer' enabled so, I assume that may initiate

Hi John, First off, let me say thanks for writing such a great piece of software! The more I learn, the more I like BPQ32. My APRS system is working great now. I will take your advice and switch to

Jean Yes, it just needs a telnet application to the ip / tcp port that dxspider uses. 73 Steve [email protected]> wrote:

If it doesn't see to work open BPQAPRS.exe at the same time, or add a lie to your cfg to open it. RUN BPQAPRS.EXE -- 73, Mark, N5MDT Montgomery, Texas http://n5mdt.ham-radio-op.net:52852

Sweet. Thanks! I’ll give this a shot Adam, KM7N

Good day, ????? Anyone here have connected DXSpider to LinBPQ as application with OUT the need of Ax25Utils on the same machine? -- 73 de Jean, VA2OM / VE2PKT

Yes.? Be sure and use a different call-ssid than your existing. APRSDIGI APRSCall=KM7N-15 StatusMsg=Tucson, AZ Symbol=& ? ? ? ?; Icon, a Black Diamond, to display for station.? Change this to a

Thanks Mark, that was it! ?As many times as I tried fixing it my old mind just didn't see it.. 73? John?? wb4moz

Your PORTNUM 2 is correct.? From there is appears to be a mismatch with the number of /*? */? that you have.? I think in the wrong order BPQ would ignore them. -- 73, Mark, N5MDT Montgomery, Texas

I would not normally check Request Reverse any time as it increases traffic.? If the other station does not have a forwarding record to you then that might be a time to use that.?? I believe that

Thanks Mark ??? Here are 2 parts - the port 2 works while port 5 still shows up in the port list: ; /* PORT ?? ?PORTNUM=2??????? ; Optional but sets port number if stated ?? ?ID=VARA

I’m wondering what are valid values range for the Enable forwarding/Request reverse fields? And what other sysops set these to when doing RF forwarding? TIA Jim KI0BK

Multi line comments work for me multiple times throughout the file. Mind sharing a part of your file that does not work? -- 73, Mark, N5MDT Montgomery, Texas http://n5mdt.ham-radio-op.net:52852

While creating a new BPQ node I used the multi line comment in several places in the cfg file. It appears that only the first instance is recognized as following ports were still showing.? I had to

No, but I create a separate directory for each instance and run from there. 73, John

Is there a command line option to specify which config file you want to use for QTSoundModem. Would like to run two instances for two different radios. Thanks, -Chris KO4YAW

I did a search and don’t find this exact topic. ?I already operate an APRS Fill-In digi/iGate based on the WX3in1mini and don’t want to duplicate that or take that one off the air—it’s

It might be simpler to use APRSISCE ( http://aprsisce.wikidot.com/ ) instead of BPQ32. And Direwolf ( https://github.com/wb2osz/direwolf/blob/master/README.md ) handles weak signals better than UZ7HO.

I would suggest using QtSoundModem rather than UZ7HO's version. https://www.cantab.net/users/john.wiseman/Documents/QtSoundModem.html Configure it to use the KISS interface, not the AGW interface. A

Right on Jeff. Also... Aprs digi section starts and stop with the following: APRSDIGI **** When it see ENDAPRSDIGI it will result in a non-critical error message if it is not a comment.? (The line