¿ªÔÆÌåÓýMy node is located at the Arts Center where any and all changes are executed from the computer.I'll double check the mail forwarding script tomorrow on Monday when I? get there. In the interim, please suggest what the script should be if what I currently have isn't working? Tnx. 73 de Chris ww2bsa.org? -------- Original message -------- From: "Mark Herson, N2MH" <n2mh@...> Date: 4/27/25 9:49 AM (GMT-05:00) Subject: Re: [bpq32] linbpq seg fault To the Group,
?
I think that this post has evolved into two separate issues.
?
1. Problems with bringing up a link between my jnos system and KD2YCK's bpq system.
2. A forwarding problem at WW2BSA.
?
This is my configuration in jnos for KD2YCK
?
# KD2YCK #
attach axudp ? ? ? ? ? ?udp-yck 256 www.host.com - 10093 10093 ax25 bcport ? ? ? ? ? ? udp-yck on ax25 hport ? ? ? ? ? ? ?udp-yck on convers interface ? ? ? udp-yck on ifconfig ? ? ? ? ? ? ? ?udp-yck description "axudp link to kd2yck via Internet" mbox mport ? ? ? ? ? ? ?udp-yck on netrom interface ? ? ? ?udp-yck 203 ?
This is identical to the one I use for N3MEL
?
# N3MEL # 2025-04-01
attach axip ? ? ? ? ? ? ip-mel 256 10.59.29.368 ax25 bcport ? ? ? ? ? ? ip-mel on ax25 hport ? ? ? ? ? ? ?ip-mel on convers interface ? ? ? ip-mel on ifconfig ? ? ? ? ? ? ? ?ip-mel description "axip link to n3mel via Mesh" mbox mport ? ? ? ? ? ? ?ip-mel on netrom interface ? ? ? ?ip-mel 203 ?
As N3MEL can agree, his link works Ok.
?
I would point out that I have set this up as an AXUDP link, not an AXIP link. Terminology is very important here. AXIP and AXUDP are separate technologies and will not talk to each other.
?
I also run a second bbs system 600 miles away using BPQ software that links to the same jnos machine, this time over 44-net. This is the map statement for that machine along with the matching jnos configuration
?
MAP N2MH 44.64.24.380 UDP 10044 UDP 10044 B
?
attach axudp ? ? ? ? ? ?udp-mh4 256 44.74.24.332 - 10044 10044
ax25 bcport ? ? ? ? ? ? udp-mh4 on ax25 hport ? ? ? ? ? ? ?udp-mh4 on convers interface ? ? ? udp-mh4 on #ifconfig ? ? ? ? ? ? ? udp-mh4 description "axudp link to n2mh4 bpq via AMPRnet" ?
Note that the UDP port can be changed. The only requirement is that both ends must agree. In this case, they do agree and the link works satisfactory.
?
For the record, hostnames and ip addresses have been changed to prevent tampering.
?
While it's possible that YCK's problem may be due to something that I am doing, I think that possiblity is remote. I use the same basic configuration very successfully for other forwarding partners.
?
As for WW2BSA, he is trying to send me a personal message, the same personal message, for the past several days. His machine does not seem to recognize the BID rejection being sent back to him. I don't want to hijack this thread with someone else's issue. So, that's all I'm going to say in this thread. I will say that I can stop the repeated forwarding attempts by going into his BBS and killing the message.
?
73, Mark, N2MH
West Orange, NJ FN20ut
Oak Island, NC FM03ww
?
?
|
