Keyboard Shortcuts
ctrl + shift + ? :
Show all keyboard shortcuts
ctrl + g :
Navigate to a group
ctrl + shift + f :
Find
ctrl + / :
Quick actions
esc to dismiss
Likes
Search
Sell my 101-07301 and my 101-07403
|
James Rice
I'm preparing to move and need to downsize my shop a bit.??I'm selling my Atlas-Craftsman 101-07301 6"x18" lathe and my 101-07403 12"x36" lathe as well as two Clausing mills.? I'm cleaning the machines tomorrow to take photos and will also inventory included tooling.? All machines will be posted on Facebook Market place as well.? I'm located in Sherman, Texas, about 60 miles north of Dallas.?
I assume my next shop will be somewhat smaller than my current 2200sqft building so I need to downsize a bit.? I still have the Wells-Index, South Bend 9A lathe, South Bend 16" lathe (10' bed), Atlas 7B shaper, Gorton P1-2 pantograph, Delta-Milwaukee Toolmaker grinder, 6 welders, multiple grinders and other smaller machines and more hand tools than i want to admit to owning to keep me busy for the last 10-20 years of my life.? So I feel I can pass some machines I rarely use on to someone who can keep them busy.? I possibly may decide to sell my Atlas shaper in the near future as well.?? These machines were my entry to home shop machining and taught me a lot.?? |
|
I wish you were closer. I really like the 7403. I have one with a 8ft bed that I'm putting I beam under right now? and boy do I wish I could have found that 7403 before I started this. I've got so many irons in the fire now that the fire can't even keep them all warm. I wish shipping wouldn't be that bad but again that's a lot of weight to ship. Let me know if your heading to WV any ways soon. I'd be interested in some of your merchandise.
|
|
toggle quoted message
Show quoted text
|
|
James Rice
开云体育The 8520 has been mine since 2008. ?It was previously owned by an elderly gentleman who used ?it as a drill press . ?The are two tiny table divets under the vise which I had never seen before because I took the vise off from the first time last weekend. ?The ways are all tight. ?It had been properly lubed as long as I’ve owned it and all the screws have good feel and no lash that I’ve noticed. ?I bought a Wells-Index almost 10 years ago and the 8520 has had very little use since then. ?Tooling included is a set of MT2 collets, a set of MT2 end mill holder up to 3/4”, the vise, a 4” rotary table from LMS ?with all accessories, a Jacob chuck on a MT2 arbor and a box of assorted clamping pieces for the smaller t-slots of the mill. ?It is 120V single phase and has tge drum switch for reversal. ?All handles are there except for the vise handle. ?I have s Snap-On female 1/2” drive ratchet handle from the 1920’s that serves as my handle and I’ll throw it in with the mill.I don’t really paint of pretty up my machines as I’m too impatient and put them immediately into service. ? The 8540 has not ran since I purchased it. ?I bought new belts and some tooling but never got that all elusive round tuit to get it up and running. ?It will come with one 1”” Type A NMTB 30 arbor and an assortment of NMTB 30 end mill holders. ?It is 3ph and will need a VFD to run. ?I probably want $1000 obo from the 8540. ? If you don’t want the tooling or the little rotary table with the 8520 mill, the price can be adjusted. James On Jan 17, 2024, at 12:15?PM, Jim Irwin <jimairwin@...> wrote:
|
|
James Rice
toggle quoted message
Show quoted text
On Jan 17, 2024, at 12:15?PM, Jim Irwin <jimairwin@...> wrote:
|
Billself
to navigate to use esc to dismiss