开云体育

Hi all, I have a strange problem with an FT-847 and hopefully someone has seen this before and can help:? I have an FT-847 that works fine EXCEPT for an issue with turning it on or off. I replaced

*PRICE REDUCTION!!!! NEW PRICE $42 + $6 SHIPPING (us)* Hello, Up for sale is an Yaesu DSP Board for FT-847. This is the original Yaesu DSP Unit. It has been tested working. I no longer have a use

It appears my advert has caused members some sort of irritation, I have therefore deleted it and the comments posted. May I suggest that if you have nothing constructive to say, don't. Leighton

I've decided to part with my 847. Ser. # 3G760154. It is in great condition. Everything works as new. Looks nearly new also. I have the original manual, power cable and hand mic. Also included is the

Hi, I do have 847 and a Digimode-4 interface (the one for the 847), what is the setting needed on the 847 and PC (Wxjt / Jtdx)? to make it run? Thanks Nimrod 4X1BG

The filter for the 847 is not common. Filter for ft1000 is more frequent. However, there are other radios available, such as Kenwood. A narrow 455 filter from a Kenwood will work, and work well. It's

Thank you Richard. I was aware of the FT-1000 MP using the same filters. I happened on to that same site as the link you sent to me.? I may pursue that avenue a little more again now.? Thanks so

Hi Butch, i'm not sure if you know but the filters in an FT1000MP Mark V are also compatible in the FT847.? This might expand your ability to locate one.? I searched a long time for the 500 Hz CW

Hello? 847 owners. I have some troubles with my 847. I experience a low volume in rx SSB, that I fix with a capacitor bypass , but remain a fault in DSP-NR only? in SSB and CW (FM/AM works

Thanks...I'll keep that in mind.

I dont have that but I do have a Inrad 2100hz that needs to be rehomed

Hello to the group. I'm a new member.? I just acquired an FT-847 and am trying to locate the optional Collins RX filter.? It is the YF-115S-02.? ?Anyone have one laying around that you would sell

Looks like your PA is self oscillating! Check decoupling caps and earthing ?Get BlueMail for Android ?

The pa itself seems fine It's pulling around 17amps on 6 but if I look at the output via an sdr the emission looks like an over horizon radar on every mode (numerous peaks close spaced and about 300k

Hi Shayne, what current does you 847 take when transmitting, at minimum power out?. At 5 watts on 6m mine takes just under 10Amps. I suspect you have a blown HF P/A unit. Leighton. GW3FSP.

HF+6 fault help. My 4m modded 847 has suddenly developed a TX fault affecting hf&6 only 2/70 are fine. when tx-ing on any hf band or 6 there is about 50% power all modes and a horrid hum/buzz on the

Hi Rafael, Any luck on finding the fault? -- Greetings from Erik Rothuis (PA2ER), Terborg Netherlands.

Looks like there is no data from the cpu. Check folowing points: * Check Q2026 for 5 volt on pin 4, on HF on reception, * Check Q2033 for 5 volt on pin 4, on HF on transmision, * Check Q2023 for 5

I would continue there will only be one fault. 73 Andrew ?Get BlueMail for Android ?

Check the voltages on J2001: 1 gnd 2 8V 3 5V J2002: 1 gnd 2 HR8 8V on reception HF 3 HT8 8V on transmit HF 4 VR8 8V on reception VHF 5 VT8 8V on transmit VHF 6 UR8 8V on reception UHF 7 UT8 8V on