开云体育

The Assigning Memory Entry function

Rick Sparber All Messages By This Member #16174 开云体育 I have found a few steps missing from what is in the book. This works for me. However, since it was trial and error, it is possible that some of it is unnecessary: ? Assigning Memory Entry (page 33) ? 1.???? Start at NO BANK 2.???? Recall the desired memory channel 3.???? Press and hold BAND until SEL starts flashing and BAND # shows where # is the band number 4.???? If necessary, rotate the dial to select the desired Memory Bank within 3 seconds 5.???? Press and hold F/W till you hear a beep and then press V/M momentarily ? ? ? I would appreciate it if others would test this out. ? 73, ? Rick KG7MQL
Don McKee, KE6DM All Messages By This Member #16180 The procedure as written in the manual works for me. As long as you're in memory mode, the memory slot currently selected is the one that will be assigned to (another?) bank. Your step 1 shouldn't be there, and the others repeat (with embellishment ;-) ) what's documented. -Don, KE6DM ------ Sent from my HP Touchpad running Android Jellybean! toggle quoted message Show quoted text On June 22, 2014 7:42:11 AM PDT, "'Rick - yahoo' rgsparber.ya@... [FT-60]" wrote: ? I have found a few steps missing from what is in the book. This works for me. However, since it was trial and error, it is possible that some of it is unnecessary: ? Assigning Memory Entry (page 33) ? 1.???? Start at NO BANK 2.???? Recall the desired memory channel 3.???? Press and hold BAND until SEL starts flashing and BAND # shows where # is the band number 4.???? If necessary, rotate the dial to select the desired Memory Bank within 3 seconds 5.???? Press and hold F/W till you hear a beep and then press V/M momentarily ? ? ? I would appreciate it if others would test this out. ? 73, ? Rick KG7MQL
Rick Sparber All Messages By This Member #16190 开云体育 Don, ? The reason I wanted to start at NO BANK is because if I am in any other bank, I am limited to the memory locations stored in that bank. What am I missing here? ? 73, ? Rick KG7MQL ? toggle quoted message Show quoted text From: FT-60@... [mailto:FT-60@...] Sent: Sunday, June 22, 2014 9:04 AM To: FT-60@... Subject: Re: [FT-60] The Assigning Memory Entry function ? ? The procedure as written in the manual works for me. As long as you're in memory mode, the memory slot currently selected is the one that will be assigned to (another?) bank. Your step 1 shouldn't be there, and the others repeat (with embellishment ;-) ) what's documented. -Don, KE6DM ------ Sent from my HP Touchpad running Android Jellybean! On June 22, 2014 7:42:11 AM PDT, "'Rick - yahoo' rgsparber.ya@... [FT-60]" <FT-60@...> wrote: ? I have found a few steps missing from what is in the book. This works for me. However, since it was trial and error, it is possible that some of it is unnecessary: ? Assigning Memory Entry (page 33) ? 1.???? Start at NO BANK 2.???? Recall the desired memory channel 3.???? Press and hold BAND until SEL starts flashing and BAND # shows where # is the band number 4.???? If necessary, rotate the dial to select the desired Memory Bank within 3 seconds 5.???? Press and hold F/W till you hear a beep and then press V/M momentarily ? ? ? I would appreciate it if others would test this out. ? 73, ? Rick KG7MQL
Don McKee, KE6DM All Messages By This Member #16201 Hi Rick, You indicated that the instructions as documented in the manual were incomplete or inaccurate. I just posted to disagree. If you want to start the process of assigning a given memory slot to a memory bank, you may start from "NO BANK" if you want to, but you don't have to if the memory slot you're interested in happens to be assigned to the currently active bank. -Don, KE6DM toggle quoted message Show quoted text On 6/22/2014 4:03 PM, 'Rick - yahoo' rgsparber.ya@... [FT-60] wrote: Don, The reason I wanted to start at NO BANK is because if I am in any other bank, I am limited to the memory locations stored in that bank. What am I missing here? 73, Rick KG7MQL From:FT-60@... [mailto:FT-60@...] Sent: Sunday, June 22, 2014 9:04 AM To: FT-60@... Subject: Re: [FT-60] The Assigning Memory Entry function The procedure as written in the manual works for me. As long as you're in memory mode, the memory slot currently selected is the one that will be assigned to (another?) bank. Your step 1 shouldn't be there, and the others repeat (with embellishment ;-) ) what's documented. -Don, KE6DM ------ Sent from my HP Touchpad running Android Jellybean! On June 22, 2014 7:42:11 AM PDT, "'Rick - yahoo' rgsparber.ya@... <mailto:rgsparber.ya@...> [FT-60]" <FT-60@... <mailto:FT-60@...>> wrote: I have found a few steps missing from what is in the book. This works for me. However, since it was trial and error, it is possible that some of it is unnecessary: Assigning Memory Entry (page 33) 1.Start at NO BANK 2.Recall the desired memory channel 3.Press and hold BAND until SEL starts flashing and BAND # shows where # is the band number 4.If necessary, rotate the dial to select the desired Memory Bank within 3 seconds 5.Press and hold F/W till you hear a beep and then press V/M momentarily I would appreciate it if others would test this out. 73, Rick KG7MQL

Previous Topic Next Topic