开云体育

Newbie Ham (Tech, Aug '20 and Gen'l, Dec '20) w/ new FT-60R.? Going thru the Owner's Manual and Rick Sparber's KG7MQL "Beginner's Guide", I am bewildered by all the features for which I have no idea

Thanks, Prasad, for that update.? I'm also fond of the 18650 Li-ion cells.? I like them much more than the pouch cells because I think they're more durable, less likely to fail due to the dendrite

Clint I bought my first FT-60 back in circa 2012 or 2013. It was a novel package but it did not do as well as my old Kenwood 7800 as far as kicking off distant repeaters. Never could find the

If you don’t re-save the new settings it won’t stick. Look up how to save to memory. Use the same channel number as the original channel. You have 2 totally separate issues here. BTW, I think

You are using NiCd packs? Original packs for the FT-60R have been NiMH. Charged properly, they should last about 750 discharge-charge cycles. But the original AC wall wart that shipped with truen

This cell phone did it again, Jardy, not Hardy. Thanks for your help. Jim [email protected]> wrote:

Hardy, sorry about the mis spelling of your name, big fingers, and I did not proof read my email. The more I think about it, it must be a battery issue. Don't know how long No cad batteries last, I

This is Jardy. If you want the power setting change to be permanent, make the change then SAVE the new settings in the same channel number. If you don’t save it, the changes will be temporary.

Thanks Hardy. I have several batteries and have charged them, but it does not seem to change anything. I set the power on low and hit the PTT. Works fine, but I'd I turn off the radio, and then turn

You have to save the new settings in the same memory slot. Also sounds like you need a new battery. You are not plugged into the wall wart, are you? The wall wart cannot provide enough oomph to

I have noticed that my FT-60 will NOT store the power setting for a repeater frequency. I can manually set the Tx power setting to LOW, and it will keep that setting. If I turn off the power or change

Guys, I had started this thread and here is my progress on this project. I bought a couple of Yaesu battery cases type FBA-25A. This case is meant to take 6 AA alkaline cells. I want to fit two 18650

HF, I used Treatstock for printing. Cost was $7.35 USD plus shipping to have the parts printed. Once you load the drawings on Treatstock you can select materials color etc. and you will be given a

Where do you get your numbers for lithium cells? Bot what Bioenno had to say.Christian KD2LIN?

Weight difference? Just don't super-size your fries next meal ... (g) Modern NiMh cells will provide close to 750 charge-discharge cycles. Lithium about half as many. -- Clint Bradford

Reduce weight.? The radio with antenna, battery case, and 6 NiMH 2.5 Ah Energizer cells has mass 364g.? I expect that substituting pouch cells will get this down to 251g which is only a little

Why go to Lithium? The Yaesu FBA-25 works perfectly for Maha 2700 mAH NiMH cells. -- Clint Bradford K6LCS http//www.work-sat.com

Hi all... Part of the reason I bought an FT-60R is that it has receive coverage of the 900 MHz band.? To my dismay, I discovered that reception is blocked from 918.5 to 943.5 MHz.? In North America,

Halden, I had mine repacked with high quality NiMH cells and haven't looked back. Andrew VK5CV Sent from Mail<https://go.microsoft.com/fwlink/?LinkId=550986> for Windows 10 Sent: Monday, 24 May 2021

Hello, Luis et. al., Wow, this looks like a great solution!? Could you share with us how much it cost to buy the printed part? I just bought a used FT-60R.? Its battery was worn out.? I cut through