开云体育

E-PIFFIANY Installed currently in 10D: crystal is 32.5200 Installed currently in 11: crystal is 32.020 10D should be 35.5200 11 should be 33.020 33.020 and 32.520. Translates to 26.000 and 26.500

https://rogerkennedy.co.uk/g3yro/ft101alignment.htm Take a look at this link. The author is a highly respected 101 service guy for Yaesu in Great Britain and is a wealth of wisdom. I resuscitated my

I have everything back together and all is working....almost all working. Band 10D is deaf. It does not hear the internal 100 or 25KHz generated tone. I have not begun to perform an alignment as I am

I finished up all the parts replacements (caps, resistors) on my FT-101B today.Throughout the past week or so, I powered up the rig twice for a smoke test and both time it passed with no burn marks

This is gonna sound cryptic......but it also makes perfect sense too. TARN-X!!!!!!!!!!!! OH-FREAKN' MY!!!!!! Big Grin. -- Butch - KA?WWT

I really appreciate your feedback. Good luck with your 101, hope soon we can see some picture when is complete. 73 OA4BMG Claudio Bio groups.io <ka0wwt@...> escribió:

The electrolytic caps I bought from a dealer on eBay that specialized in the kits for the FT series radios. https://www.ebay.com/str/kk4hxj?_trksid=p4429486.m3561.l161211 The particular resistor you

Hello Butch You are in the process that I need to start. It’s not easy at all for those of us who do it for the first time. Here in Peru is not too easy to found parts for old stuff. I ordered

I got through the toughest part, for me anyway, of the electrolytic cap change today. The power cap’s, are finally done. It was a challenge to come up with how to get the wires soldered to the new

This is normal behavior without an external VFO Alex. Erwin, PA3DAF

Would appreciate if someone who owns a FT-101ZD could tell me how their VFO display behaves without external VFO connected and when switched to " EXT " " TX-EXT ", " EXT-RX "? Does the digital display

My FT-101ZD? (ZSD) radio exhibits strange behavior with external VFO. I took a chance and purchased a used FV-101DM and can’t get it working. I purchased 2 ‘new’ interface cables to go with the

Congratulations OM.? Been there, done that on the caps.? So I can also say your confidence is well earned.? This is quite a rig to do cap swaps on.? There must be a millon of those damned green

I just finished (sorta, 3 to go) the cap replacement on all the removable boards. The worst of all was the cap in the 1180 module. But, I got it. I decided I was gonna find out sooner or later, so

Good luck.

Well, I finally have all the initial parts to begin the process of the resurrection of my FT-101B. The Heathkit VTVM will be here today and I will get that inspected, cleaned up, and

Jacques, your guess was correct, pretty clever thinking. Thank you for replying to message with your help. *C9:* It was labeled NTK 112K, only have a multimeter and it measured open (no

Hi Alex, Call it an educated guess if you like, but I believe that C9 in the output tank section, is defective (ceramic, 100pF, 3kV rating cap). 73, Jacques, VE2JFE in Montreal SYMPTOMS: -

SYMPTOMS: - Full output power (sometimes) on 80m only. - Reduced output power only at ca. 50% intermittently (sometimes) and on 80m only. - All other bands operate normally. Otherwise the transceiver

Thanks for your suggestions Bruce. I have both a DVM and an old analog Simpson 260 VM. I love analog meters. An O’scope is the one thing I don’t have but I do have access to one. I have use