开云体育

I would assume this cable would work. I am using it with a FTM-6000. https://digirig.net/product/yaesu-ftm-cable/ Tyler Griffiths N7UWX See where I

Lawrence - did you ever get this resolved? I'm having the symptoms.? I'm using Yaesu's CT-164 10pin to 6pin cable connected to the digirig 6 pin (male) 1200 baud to TRRS audio.? I've also used the

George, this is a very timely post as I was trying to do exactly the same yesterday. I followed the recipe that Steve K3FZT posted, but I am having issues with the PTT. I am using an IC-9700 as the

It's trivial UNTIL you want to run two or more sound card apps on the same sound device at the same time (such as both AX. 25 packet with the UZ7HO Soundmodem -AND- VARA ).? Then all hell breaks

I am relatively new to this. I use VARA HF with an Icom IC-7300 and VARA FM with Alinco DR-135 and Repeater Builder 9600 interface. Both use PTT, just by checking the box for RA-board in VARA setup.

?VOX (as in a SignaLink or the "DATA VOX" function on some Yaesu radios) has huge advantages.? You avoid the hassle of serial ports, especially on modern computers that force you to use a

Why are you using VOX ? It's not needed in the setup as sound modem has its own PTT. [email protected]> wrote:

Yes, it was Bullard's Beach! We had amazing fish'n'chips at a little place in the harbor, and enjoyed a cranberry bog tour. We found that the cranberry-rum jam was amazing! Sadly, the day we drove

Scott, I have gotten SoundModem working flawlessly for several YCARES gateways I switched from hardware packet TNCs to using DRA's or SignaLinks where I new I need to use a program that only supported

That would be Bullard's Beach State Park. The local radio group often has POTA activations there. I am on the bluffs above Old Town and my Gateway has excellent coverage. Bring your

Thomas, Thanks for that information. I'm not sure exactly what led me to think that the "Radio only" mode was correct, but glad I was finally able to stumble my way to a working solution! BTW, I saw

Congratulations on sorting out issues! I strongly suggest that you stay as far from the Radio-Only modes as possible. These modes were written into the Winlink software to serve as a last resort in

Thank you, thank you, thank you. For all the advice and comments. I have both packet and VARA FM working on the test gateway. Tonight I installed COM Port splitter software and set up two com ports.

Hello All, Well, I feel kind of foolish posting this, but I got my Winlink/VARA-FM/AIOC/Baofeng combo working, and it was partly due to my ignorance and an unexpected hardware issue. My hardware setup

I also calibrate for VARA FM but aim for the VARA FM receive level to be around -6dB. This produces a good deviation level with Sound Modem. Tom N5TW _._,_._,_

I agree that it can be difficult to get optimum levels for both packet and Vara FM. I usually optimize for Vara FM as soundmodem is pretty forgiving and seems to do well with a wider range of levels.

John Denison The only thing that could interfere with performance is the COM Port splitter, it is software and software does run on a processor and it theoretically could cause a truncation of

Have you considered setting up two gateways on the same PC? It seems like every gateway in my area that has both packet and VARA FM on the same radio & sound card has poor performance (speed step

Brian (W7OWO) has been a very beneficial consultant for our (K7MAR) project. After much hair pulling and frustration the "Mike Spohn N1SPW" document "Windows-11 Digirig Sound Settings" got us on the

The C-Media CM-108 and CM-119 sound chips, ? used in many USB sound "dongles" sound card, and used in several ham digimode interfaces (DigiRig, Masters DRA, etc), ?? have a single-bit I/O pin in