开云体育

When I use the TUNE button on VARA FM on my PC, I have to click on the TUNE button a 2nd time to stop it from transmitting.? I believe the lable changes from TUNE to STOP, or something like that,

Sorry, I responded to the wrong thread. Please disregard.

Thanks,. Yes, I have no problem with the Alinco DR-135 radios. My issue is with the TYT TH-9000D and it does not have a digital mode channel programming option. It does have a connector on the

Gary; Some Alinco transceivers have provisions for data communications, with some form of dedicated 'DATA' connection apart from the mic and/or external speaker jacks. The key advantages of such a

The Alinco has a special button for digital modes. Make sure you turn this on. Gary [email protected]> wrote:

Bob, Not specific to VARA but perhaps a clue: I was working with a local group here in LA that supports an extreme marathon race in the mountains above the LA basin. We have a 220 packet network that

If the radio is transmitting and the RMS is responding, then the interface is working.? I would suggest turning the audio levels down (may have to use the Windows Sounds and Sound Settings apps) and

I am running Windows 10 for Raspberry Pi4B and VARA FM 3.8.4.? When I try to TUNE the soundcard ( Signalink USB) the PTT led comes on and the radio triggers but will not release with the CLOSE

Dave; Did you get the call sign for this VARA FM Gateway station from your Vara FM Winlink session channel selection list? Assuming you're operating in Snohomish WA, I see lots of VARA FM stations

No I didn't. In my case it is simply a plug and play to change radios. I didn't change the drive level from the DRA-36. The response from the VARA pings to a couple of local digis was virtually the

Do you need to change any settings in VARA or the interface when you switch between the DR-135 and the TD-9000D? [email protected]> wrote:

Bob, I have been using VARA FM with my DR-135 and also a TYT TH-9000D. I added the 9 Pin D connector to the stock TH-9000D with the same DB9 pinout as the DR-135. I am using the DRA-36 36 Masters

I have two TYT TD-9000D low cost Chinese radios and am having trouble getting them to work with VARA FM.? I thought I had this working with the Repeater Builder RIB ALINCO 9600 and the DB9 adapter

On 2/16/2025 3:26 PM, Mark Davis via groups.io wrote: > On Sat, Feb 15, 2025 at 09:31 PM, WA8LMF wrote: > > I would think that it should be WIDE, but perhaps someone else can confirm that. > >

Stephan; You are correct about the FT-991A internal sound card system not having the audio bandwidth to fully support VARA FM 'WIDE" mode, but keep in mind that VARA FM RMS Gateway (and P2P) stations

The built-in sound card of the FT-991 (identical to the external Yaesu SCU-17 interface)? lacks the audio bandwidth for VARA-FM wide.? To achieve the highest speeds VARA-FM is capable of, you have

Thanks, Keith -- I received your message after switching over to VARA HF.? It looks like the only VARA-FM winlink server near me is not fully operational :-(? The signal coming from it is strong,

Dave K7XST wrote… I was going to ask if the message stuck in your outbox was P2P instead if Winlink format, but… I see where you connected to the RMS, but I don’t see any evidence that it

The RigBlaster Nomic is just an audio coupler/isolator - there is no sound card in it like the DigiRig.? You would have to connect it to another sound system such as the one in the computer -- or --

Sorry I meant IC -F320. I got it sending and receiving emails with a Digirig and Digirig cables, but not with the Rigblaster. So I need to spend a bit more time with the Riglaster documentation. It