开云体育

I have a similar toolpost on my Bosch lathe. It works perfectly. Am 07.11.2024 um 17:27 schrieb Herman de Leeuw via groups.io: -- Diese E-Mail wurde von AVG-Antivirussoftware auf Viren geprüft.

Does anyone have experience with the "Emco-Lux Adjustable Toolpost" that was advertised in the Campbell Tools Co catalog for March 1983, entitled "Lathe Accessories and Attachments" (see *here (

Does anyone have some input on the erstwhile Edelstaal "cutting tool/slotting tool"? I found it in the Campbell Tools Co catalog for March 1983, entitled "Lathe accessories & Attachments" which is

So you have the U90 motor. A wiring diagram can be found here... URL https://www.lathes.co.uk/unimat/page12.html More info can be found here... URL https://www.unimat-vintage-lathe.com/motortips.html

On AC motors just reversing the power wires will do nothing except potentially exposing you to an electric shock because you reversed the line and neutral wires (This is not necessarily an issue on

Ron, there are members with good knowledge of electricity and electronics. I was able to point to the short because I had a motor that did the same and I had to dump it because the rewinding fees were

Would it still run with a short? Is there any way to test it to locate or at least verify the short?Thanks?Sent from my Verizon, Samsung Galaxy smartphone

There is a Unimat SL 1000 up for auction on shopgoodwill.com. URL: https://shopgoodwill.com/item/214799119

Do you think 7.2 mm spindel hole can be simply reamed to MT0 with 9 mm major diameter? Or boring is needed? In the latter case boring bar would have to be very thin lacking rigidity. Have you actually

Sounds like there is a short in the motor. Best Regards, Andrei mailto:calciu1@... ________________________________ Sent: Tuesday, November 5, 2024 11:59 AM To: [email protected]

I recently acquired a Unimat SL Model DB 200.? Motor was a little noisy, so I disassembled it, cleaned it up and put it back together.? It runs well, but in CCW rotation.? I believe it should be

I've not bought MT0 taper reamers but do have MT2 & 3 reamer sets. Imports cost me less than $30 per set then.? Looks like an import set of a roughing and finishing reamers in MT0 can be had for well

Recently I came across LatheCity.com which offers MT0 tail and headstock spindles for Unimat SL. They look great, but the collar on the headstock is a separate part held by set screws. This is a bit

I would suggest checking to see if the tailstock spindle was parallel to the bed, and if it is, make an adjustable chuck mount similar to the ones sold by Sherline for their lathes.? By using an

Hi Carl. Somebody else has tailstock problems. I do agree with you that using a good indicator is an easy way to measure offsets. Get Outlook for Android<https://aka.ms/AAb9ysg>

Hello Andrei: Do you have an indicator? It would be best to start by measuring how far out the tail stock is. Hold the indicator in the headstock and rotate it inside the Morse Taper of the tail

They were made in Taiwan. Best Regards, Andrei mailto:calciu1@... ________________________________ Sent: Sunday, November 3, 2024 4:26 PM To: [email protected] <[email protected]> Cc:

Not sure, tha plate says Austria... But that might only be for final assembly... Seems I need to tweak it regardless... ;) /Anders Den s?n 3 nov. 2024 kl 18:53 skrev Neil Morrison

Weren't the Unimat 4 machines Chinese made? I remember messages on Yahoo about issues. You may have to tweak it. Or, I could be wrong. But that is my memory. Neil. [email protected]> wrote:

This from Tony Lathes - https://www.lathes.co.uk/emco-unimat-3-and-4/ Built in Austria the Unimat 3 was very well made and became enormously popular; when equipped with a range of accessories (and if