开云体育

Greg, It appears that you've hijacked the thread "Driving GPIO pins," and created a lot of confusion for those following the thread. Don't know why you'd do that without any mention why. As far as I

Tnx,?I forgot the hookup, thanks for the info!73 de Greg Sent from the all new AOL app for Android On Tue, May 18, 2021 at 4:17 PM, vhsproducts via groups.io<vhsproducts@...> wrote: It

It strikes me as a lot of work to replicate a product ( Well, hopefully) that you can have in your hands from Byonics in two days, but a Ham's quest for knowledge ( And getting stuff done less

Looks similar to this one https://cdn-shop.adafruit.com/datasheets/TC2004A-01.pdf Byonics makes a display and interface for the TT4 https://www.byonics.com/downloads/tt4_display_v1.3.pdf I don’t

I sent you these pics. LCD with some I/O connections I thought to display APRS data?Greg Sent from the all new AOL app for Android

Sent from the all new AOL app for Android On Tue, May 18, 2021 at 2:05 PM, Robert Bruninga<bruninga@...> wrote: I need more info.? What is that board? thanks Bob (in chemo fog)

I need more info. What is that board? thanks Bob (in chemo fog) <k7sdw@...> wrote:

Bob,I think I bought a TC2004A-03R board to interface with my TT4.Have you or anyone in groups.io have the hookup and command settings for this board? Thanks, Greg

Thanks for that, Rob. Here is what I often tell people about digi setup: To configure the stationary TT4 as a digipeater, Connect the TT USB cable to the computer and install drivers if needed Run a

I believe this is typically the very first part of TSTAT PHG5360/WIDE because that is appended to the position TX.?? According to the protocol, TSPEED should be FALSE ?? I am not sure about BText

uidigi is an eprom that you burn after you did a files with your specs and there you go. you can enter in command mode via rf so it is no1. anyhow if you find your way with the tt4,good 73 and great

I'm going to work on it some more when I get home from work today, i'm not planning on having a gps attached to it, its probably left over from when I used to run this in my truck. I'm trying to make

I guess I don't find the TT4 any more difficult to program than other TNCs I've used. Comparing command summaries, I really see that the1270C had many fewer.? About the only difference I see is that

Robert i understand you very clearly, they are not easy to ^rpgramm at all . no offence but i prefer my UIDigi with my old 1270C ,not that the TT4 is not good it is just complicated to programm 73 and

I am not sure what you are asking when it comes to "fixed".Fixed means not moving and so if your location doesn't change, you are fixed. If you are concerned over the mic-E status being a bit untrue,

I'm wondering what is the command to have it say that its fixed? Currently it says mic-e where a normal digi says fixed, unsure if i can put details on the power and the antenna direction also my

Hello Bill, Thanks for sharing with us your tricks for your install. You have given us a few ideas for our future installs. Regards, Doug VK2XLJ ________________________________ Sent: Friday, 7 May

Yes, it's an active antenna with 28dB gain also. https://www.amazon.com/gp/product/B084GRWP5D I've been using several mag mount GPS antennas but just didn't like the coax across the roof and in

Is that a passive or active antenna? Many gps boards feed dc antenna power up the center conductor (through an smt choke and then capacitively couple the signal into the module). This is a nice active

Last stop is a $13 GPS antenna with SMA connector from Amazon. I popped some of the plastic off around the windows and was able to pull the headliner down enough to safely drill a hole for the