Re: Tek DM44
Jordan, I found the origin of this manual. I bought it from AA4DF site . Since they carefully scanned and sell this hi quality manual (I paid $10 but I think now it is just $4.99), I think it is no
By
EB4APL <eb4apl@...>
·
#34856
·
|
Re: Tek DM44
Jordan, I have the service manual in pdf. It???s about 12 Mb. It is a hi quality scan that I downloaded some time ago, I don???t rememeber the source so I can???t give them the due credit,
By
EB4APL <eb4apl@...>
·
#34855
·
|
Re: 067-0587-02 (was Calibrating a 7704A)
d.seiter@... escribi???: Mmmm... let me see... yes, the exoticc elastomeric switch! Well, it has also quite a lot of exotic hybrids :) Regards, Javier --
By
fjh001
·
#34854
·
|
Re: 067-0587-02 (was Calibrating a 7704A)
One of my two was DOA through this. Inside the switch ("do not open" says the manual. Ha!), the cunningly shaped elastomer had a tear in it, and was failing to operate two of the contacts. A bit of
By
Craig Sawyers <c.sawyers@...>
·
#34853
·
|
Re: 7603 filter caps
Deane is quite right. Think about it this way - when the bridge diode turns on, the capacitor charges up through the secondary resistance of the power transformer and the reflected primary resistance,
By
Craig Sawyers <c.sawyers@...>
·
#34852
·
|
Re: 7603 filter caps
I wouldn't say that the ESR meter is "required", but it sure makes life easier! Plus, it's a cool kit to build (if you happen to go that route...;-)) -Dave
By
d.seiter@...
·
#34851
·
|
067-0587-02 (was Calibrating a 7704A)
I decided to pull out my 067-0587-0x's and realized that I'd never tried the -02. Of course, I find it has problems, like the gain steps aren't there. I only have the manual for the -02, but I assume
By
d.seiter@...
·
#34850
·
|
Re: 7603 filter caps
That may be so, but when repairing relatively modern equipment with many many caps that need to have low ESR for the circuit to work (e.g. switching voltage converters) it is absolutely great to be
By
Stefan Trethan <stefan_trethan@...>
·
#34849
·
|
Re: Calibrating a 7704A
This reminds me that I need to do a "group cal" on all my gear. I have both fixtures, but I just never get around to it. The individual scopes are all cal'd, but when I start swapping plugins, I
By
d.seiter@...
·
#34847
·
|
Tek DM44
Anyone got a manual for a DM44? Owners and/or service. ~Jordan~
By
Jordan Kersten <jordankersten@...>
·
#34846
·
|
Re: Tek 465B blurry CRT.
Hello, There was also an entire batch/lot of problem 465B crts from back in the day. One of the problems was spot size and ability to focus. Many were replaced under warranty by Tek. I remember
By
Bernice Loui <rupunzels_window@...>
·
#34845
·
|
Tek 465B Blurry CRT - Photo
I posted a photo of the blurr to my album. You can't see it well in the pic, but it looks much worse and fuzzy/blurry in real life. It looks like it is focusing right, there just seems to me a shadow
By
Jordan Kersten <jordankersten@...>
·
#34844
·
|
Re: 7603 filter caps
Hello Scott, Thanks for posting the link to the Anatek ESR comparison page. I have both the EVB from Portugal, and the CapAnalyzer 88A that are on the Anatek comparison page. The EVB is another modern
By
tom jobe <tomjobe@...>
·
#34843
·
|
Re: Tek 465B blurry CRT.
Take a look at: http://www.fullnet.com/~tomg/tekclean.htm where there are procedures that try to address this problem for both the 465 and 475 scopes. When I had a 475 I did this procedure and it
By
Dino Papas <kl0s@...>
·
#34842
·
|
Re: Calibrating a 7704A
The key thing about the cal fixture is that it calibrates the mainframe independent of plug ins. So you adjust horizontal and vertical gains, and trim up the rise time of both vertical and horizontal
By
Craig Sawyers <c.sawyers@...>
·
#34841
·
|
Tek 465B blurry CRT.
My 465b won't focus quite as clear as it should. Doesn't matter where I adjust the focus or astig control. It looks like there is a ghost image of whatever I am measuring. So the trace/waveform
By
Jordan Kersten <jordankersten@...>
·
#34840
·
|
Re: 7603 filter caps
See this web page http://www.anatekcorp.com/testequipment/esrcompar.htm - There is what is known as the 'Bob Parker' design this is a cheap accurate ESR meter upon which countless commercial
By
Scott McGrath <mcgrath@...>
·
#34839
·
|
Re: 7603 filter caps
Using higher Voltage/Capacitance ratings usually is not a problem especially since many of the old can type electrolytics were rated -20/+40% of nominal rating. Higher voltage is usually ok as long as
By
Scott McGrath <mcgrath@...>
·
#34838
·
|
7603 filter caps
Hi folks, Thanks for all the tips in this forum. I am just stating to work on a used 7603 with three plug-ins (7A18A, 7D15, 7B70) I acquired cheap as a second scope with a 442 I got also got cheap
By
Robert Simpson
·
#34837
·
|
File - Posting Rules
Please edit any posts/replies to the list to minimize quoted material to that required for continuity. Please do not send personal replies to the list. List replies go to the original sender by
By
TekScopes@...
·
#34836
·
|