开云体育

Hi Bob, There is some possible incompatibility using the 7A16P in a normal 7K mainframe such as the 7704A. The 7A16P was specifically made to be used with the 7912AD digitizer and is programmable

As I recall, the reason Tek would not recommend a 7B53 as a timebase for a 7704 is that it will not sweep fast enough to take full advantage of the 7704's 200 MHz bandpass. Other than that, I believe

Hi all, :) A couple of times recently there have been mentions of people who hold some stocks of Tek parts for sale for replacements. (e.g. pots, transistors, tubes etc). After a recent rebuild

Hi All, I am looking for two (2) Tektronix 475 Position Pots. Tektronix Part Number 311-1411-00. Regards, Andrew Campbell Calibration and Repair Network Pty. Limited A.B.N 64 090 761 363 An

Yes, that's what I was talking about... I know it's written up in one of the manuals or catalogs, but I can't seem to locate it at the moment. I guess I'm just picky :-) On the other hand, 7B8xs are

bandwidth 7B53A's And Seconded - before I acquired 7B87, later -92As via a package deal: a 7B53 in my 7854 (400 MHz nom) scope worked fine. At fastest sweeps, with a known ~700 pS risetime pulse

The pot/switch for the CAL/VAR volts on Ch1 of my 2230 is disfunctional and there is no detent. Manual says 311-2218-00 Tek part number, but it describes it as an Allen bradley 10K pot with

There's not a darned thing wrong with using a 7B53A in a 7704 or 7704A. It's the 7B92/A that you can't easily use on lower bandwidth scopes only because they can't handle the faster sweeps. And

The 7B53/7B53A is not recommended for use in the 7704/7704A. I don't remember why, but I think it was a good reason. The original poster needs to find a 7B70+7B71, 7B80+7B85, or 7B92/7B92A.

The Often the Tantals for Supply Decoupling having a short. The Chokes which are lo

Good Evening I have a 7704A mainframe that is in need of repair. I turned it on this morning after not having been powered up for about 2 years. The trace was moving around erratically. Then I

Bill, if you don't mind knobs that aren't perfect, I have enough used ones to set up. They may be cracked, have a soldering iron ding, have some paint rubbed off, but they're serviceable. When I

Hello, Would anyone have a vertical output hybrid for a 7844? Tek part 155-0064 I believe... If anyone has a 7844, I can email them the necessary pictorial info where the part is and how to remove it

This allows as Interesting... thanks! So it's the 2/3 series equivalent of the type Q strain gauge then, I assume. George

Hello, if anyone has access to or knows a source for the following 466 parts, I would be grateful: - (2) A&B trigger level knobs #366-1280-00 - (1) B trigger slope knob #366-1278-00 - (1) vertical

What's REALLY bad about leaving the filter out of the 465/475 scopes is when they're used "IBM" style -- rear on the floor while working on equipment. That fan "vacuums" up every dust moozie in

the is (and Hello Dean, I remember the Filter-Kote (milky water-soluble oil?) days for the metal filters in the 5xx scopes (!) I've been cutting up the

Hi George, The 3C66 interfaces to a wide variety of mechanical transducers. This allows display of all kinds of mechanical measurements on the CRT face such as vibration, mechanical shock, shaft

What does a 3C66 carrier amplifier do, or what do you use it for? Thanks! George

manual That can be some handy information. But be forewarned about U.S. Army calibration T.O.s (Technical Orders) which the USAF also uses. I have seen some that leave a lot to be desired. For