Re: WTB: Case ring for 466
I have used Jeff's feet and can vouch for the quality of the 3D printing. -- Michael Lynch Dardanelle, AR
By
Michael W. Lynch
·
#184856
·
|
Re: Paper Used in Older Tek Manuals
rick, maybe I am a little OCD about this, but I also once worked in a print shop as a typesetter, back when such things were still things. Producing good looking printed and bound materials still
By
Jeff Dutky
·
#184855
·
|
Re: WTB: Case ring for 466
I will add my endorsement here as well. I recently bought four sets from Jeff (our own Jeff Davis). They are excellent, 3D-printed replacements. Cheers, Tom -- Prof. Thomas H. Lee Allen Ctr., Rm. 205
By
Tom Lee
·
#184854
·
|
Added Folder /6127B
#file-notice
Bruce Lane <kyrrin@...> added folder */6127B*
By
[email protected] Notification <noreply@...>
·
#184853
·
|
Re: WTB: Case ring for 466
Bruce, The cord wrap feet can be had easily enough from n0dy Jeff on eBay, $27.30 for as set of four (he doesn't list the 466, but it clearly uses the same feet as the 465 and 475). He used to sell on
By
Jeff Dutky
·
#184852
·
|
WTB: Case ring for 466
I recently got a 466 to restore. The most important mechanical part I need is the plastic rim that goes on the back of the chassis to hold the case on. In the repair manual, It's called? "FRAME SECT,
By
greenboxmaven
·
#184851
·
|
Re: TM 504 Power Module Questions
I think you got that backwards Pins 1 thru 13 (bottom) are all the same Pins 14 thru 28 (upper) are mostly custom select as per units allow. Don't forget side A and B looking from the front A is on
By
[email protected]
·
#184850
·
|
Re: SG503 question
Mine is an early serial number B0102xx an still well within specs. Jeff
By
[email protected]
·
#184849
·
|
Re: Paper Used in Older Tek Manuals
Dave Henderson of Artek manuals posted awhile back showing how to replace a comb binding. DaveD
By
Dave Daniel
·
#184848
·
|
Re: Paper Used in Older Tek Manuals
I bought a bunch of black and white combs and a small-capacity comb punch a while back. I used it to replace many crumbling Tektronix manual combs, as well as binding various other documents (such as
By
Dave Daniel
·
#184847
·
|
Re: Paper Used in Older Tek Manuals
Years ago (2006), I found a comb binder on ebay. It was about $112. Did not include supplies, which are easy to get. the trade name was Ibimatic, which is a brand of Ibico. It's handy to have. I don't
By
rick
·
#184846
·
|
Re: New (old) 2247a enquiry
Thanks, that fixed it. Bit embarassing, should have read the user manual before looking at the service manual.
By
Richard Merifield
·
#184845
·
|
Re: SG503 question
I can check the 2 of mine if that would help. I would suspect that they are close to spec if not in spec. I am curious if the 2 where the output is falling off are early serial numbers and the one you
By
Zentronics42@...
·
#184844
·
|
Re: SG503 question
Zen, Thanks for your reply. Table 3-3 of the manual suggests typical LF limits of 4.70 and 9.09 MHz on the two ranges in question. My units get very close to, or past, these values before the output
By
romeo987
·
#184843
·
|
Re: Ballantine Calibrator manual
Thank you! I have scanned and uploaded the Ballantine 6126M manual to KO4bb and BAMA. I have an early and late 6125B/C manual that is in the que to be scanned and uploaded...
By
Ken Eckert
·
#184842
·
|
Ballantine Calibrator manual
Fellow Tekkies, You find the darndest things when you're cleaning up. In this case, it was a clean reproduction of the operating and service manuals for the Ballantine Labs 6127B O-Scope calibrator.
By
Bruce Lane
·
#184841
·
|
Re: Advice on fixing 2465B slow horiz sweep
Sorry that I haven¡¯t been following this thread closely, so forgive me if you¡¯ve already explicitly verified that the vertical calibration has not been affected. But if the vertical gain is off by
By
Tom Lee
·
#184840
·
|
Re: Paper Used in Older Tek Manuals
Thank you Toby and Ken for making those measurements. I have several reams of paper on order (28 lb and 32 lb because, as you say, heavier feels better). At the moment I'm using a blue 1/2 inch 3-ring
By
Jeff Dutky
·
#184839
·
|
Re: Paper Used in Older Tek Manuals
FWIW, I weighed 10 pages of a Tek 515A manual, I got approx 107 gsm -- approx 405 gsm for the blue covers. Of course heavier always feels better (I would try at least 120 gsm equivalent). --Toby
By
toby@...
·
#184838
·
|
Re: Advice on fixing 2465B slow horiz sweep
------- There are good suggestions in the other posts too. Given t
By
Ozan
·
#184837
·
|