开云体育

ctrl + shift + ? for shortcuts
© 2025 Groups.io
  1. SHARI
  2. Topics

COR Settings

Shawnerz
 

OK, I found I could get back to the Tune Interface CLI from Updating the Node. OK, So that's good.
But, i am still trying to get the node to receive. I have no indications of receive activity by the LED. The activity LED stays slow flashing green when inactive. When transmitting the test tone, the Red LED lights and the green LED goes to fast flashing.
Thanks,
-Shawn

On Monday, February 24, 2025 at 04:56:33 AM CST, Shawnerz <shawnerz@...> wrote:





Hello all.
I'm new to AllStar and SHARI and the SA-818.
I have most of my node (64402) configured. I've watched videos and done reading but this last setting is confusing me.
The VHF SHARI-Pi node can send the tone with the "flashing" PTT. I hear the tone in my HT. But when I key up my HT, it is never "seen" by the Pi.
I am CTCSS and I am confident the HT and Pi are configured for the same tone (100.0 Hz).
I am confident the HT transmit frequency and the Pi receive frequencies are set to the same frequency (146.52).
The only other option I can think of is the COR setting. I am running a Raspberry Pi 4B with a VHF SHARI Pi with a SA-818 module.

If someone running a similar setup please tell me what they have theirs set to?

And, as an aside, why is it you can only get to the COR setting menu by removing and re-adding the node in the ASL menu? Wouldn't make more sense to make those values available in the SA818-menu? Or, am I overlooking something obvious? I've missed many obvious clues in my past. This would not be the first.?
Thank you,
-Shawn
Shawnerz
 

Hello all.
I'm new to AllStar and SHARI and the SA-818.
I have most of my node (64402) configured. I've watched videos and done reading but this last setting is confusing me.
The VHF SHARI-Pi node can send the tone with the "flashing" PTT. I hear the tone in my HT. But when I key up my HT, it is never "seen" by the Pi.
I am CTCSS and I am confident the HT and Pi are configured for the same tone (100.0 Hz).
I am confident the HT transmit frequency and the Pi receive frequencies are set to the same frequency (146.52).
The only other option I can think of is the COR setting. I am running a Raspberry Pi 4B with a VHF SHARI Pi with a SA-818 module.

If someone running a similar setup please tell me what they have theirs set to?

And, as an aside, why is it you can only get to the COR setting menu by removing and re-adding the node in the ASL menu? Wouldn't make more sense to make those values available in the SA818-menu? Or, am I overlooking something obvious? I've missed many obvious clues in my past. This would not be the first.?
Thank you,
-Shawn
 

First, the COS LED is inoperative until you enable it as explained in this document in the Files section of this group
?
?
But you can see whats happening by looking at selection V in the Tune Interface CLI
?
?
Be sure CTCSS is Off (selection J above)
?
Also make sure you are in the correct mode, Duplex type 1 in the Node Setup Menu
 

开云体育

Since you don't have a call sign, no idea where you are located. But . . . if you are in the USA, you should never put a device on a national calling frequency (such as 146.52 MHz). It is a calling frequency.

Mick - W7CAT

----- Original Message -----
From: "Shawnerz via groups.io"
To: "[email protected]"
Sent: Monday, February 24, 2025 03:56:33 AM
Subject: [SHARI] COR Settings

> Hello all.
> I'm new to AllStar and SHARI and the SA-818.
> I have most of my node (64402) configured. I've watched videos and done reading but this last setting is confusing me.
> The VHF SHARI-Pi node can send the tone with the "flashing" PTT. I hear the tone in my HT. But when I key up my HT, it is never "seen" by the Pi.
> I am CTCSS and I am confident the HT and Pi are configured for the same tone (100.0 Hz).
> I am confident the HT transmit frequency and the Pi receive frequencies are set to the same frequency (146.52).
> The only other option I can think of is the COR setting. I am running a Raspberry Pi 4B with a VHF SHARI Pi with a SA-818 module.
>
> If someone running a similar setup please tell me what they have theirs set to?
>
> And, as an aside, why is it you can only get to the COR setting menu by removing and re-adding the node in the ASL menu? Wouldn't make more sense to make those values available in the SA818-menu? Or, am I overlooking something obvious? I've missed many obvious clues in my past. This would not be the first.?
> Thank you,
> -Shawn
>
>
>
>
>
>
--

 

开云体育

> I have most of my node (64402) configured.

?

Is that node number correct?

?

That shows W5NI on the Allstarlink site, and when I look up that callsign on QRZ, I get:

WILLIAM K HULSE

10904 NE BLACKWELL RD

LEES SUMMIT, MO 64086-6624

USA

?

?
Shawnerz
 

Mick,
The ShariPi is in testing mode, in my house, on a stubby antenna testing with my HT, on low power.
When it deploys, it will be augmenting our club VHF repeater, W5NNI, on our VHF repeater frequencies.
Shawn - N6REP
?
Shawnerz
 

The node number *is* correct.
However, the callsign you have is *not* correct. Our club callsign is W5NNI. QRZ link here:
From where I'm sitting, the Allstarlink site has our node listed with the correct callsign.
For the record, I'm Shawn, N6REP. I know it doesn't mean anything, but I am the current president of the MFARC and can also be reached at president@....
Thanks,
-Shawn
?
 

开云体育

Thanks for the clarification Shawn.

Sorry for all the suspicion.

 

开云体育

?

“When it deploys, it will be augmenting our club VHF repeater, W5NNI, on our VHF repeater frequencies.”

?

I hope you mean you will be integrating the Pi into the repeater set up directly, NOT through an RF link. The shari is not intended for that application.

Get an interface intended for repeater use, like a DMK URI, something from Masters communications etc. Set the node up for full duplex operation.

?

1 - 9 of 9