开云体育

After five months I still cannot connect my RE230 to my iPhone or iPad A. Yes all drivers, firmware, software and squirrels are up to date. Funny thing, the first time I used it on my iPhone, it worked then lost connection and I have not been able to reconnect. AntScope 2 just does not show the RE230 device on a search. Fortunately I have an old Android tablet that will work with the RE230. So anyone else still frustrated with lack of IOS support?

Hi all, FS Rig Expert TI-5 and TI-Plus. $70 shipped lower 48. Cables available for $40 each shipped lower 48: YS-009 (For Yaesu FTDX-9000D) - 2 YS-007 (For Yaesu FTDX-5000D) Icom 7pin Din radios + CI-V + keying cable 1/4" -1 EL-001S ( for Elecraft K3/K4 maybe other Elecraft) These are nice interfaces as many of you know, excellent condition. CW/USB/Data/Rig control 73 Darrell AB2E

Let me start by saying that I've had an AA-600 for seven years, so I'm quite familiar with the form factor and general operating characteristics of the flagship "green" analyzers. Somehow my initial review of the AA-600 was erased from eham.net (I was review #1 of that analyzer), but my follow-up review is still there. I had mentioned that they should make a rubberized cover for the device, which was never done...until now! The AA-3000 ZOOM comes standard with a silicone cover. This is a nice touch, even if it isn't going to be as durable as a rubberized cover. Also, you can't get to the battery compartment with the cover on. This is a bit of a mistake, but the cover is nice enough if not super tight fitting. The tradeoff for the silicone cover is that they no longer include the nice blue case. The AA-3000 ZOOM came to me from RigExpert USA with version 1.0 firmware. Today v1.1 was released, but I can't see any difference and the info file lists 1.1 as the initial release. So maybe they just re-released 1.0 as 1.1. Not sure. I believe functionally its identical to that of the AA-2000 ZOOM except that range has been extended to 3GHz. I don't think there are any other changes and the AA-2000 ZOOM has already been extensively reviewed, so I won't elaborate further. Now for the bad. Firmware versions 1.0 and 1.1 have a bug that function F + 0 freezes the analyzer and only a battery removal will reset the device. None of the buttons work as the analyzer is frozen. I've notified RigExpert Ukraine and RigExpert USA & Canada but haven't received any feedback on this issue. Initially I wasn't sure if the Bluetooth module worked in my AA-3000 ZOOM. I couldn't get it to work with any external software. I knew from reading the forums that AntScope2 didn't support BLE yet, but I had the latest AntScope for iOS which was supposed to support the AA-3000 ZOOM. It does not. AntScope2 for Windows and Mac is now out in a beta (v1.3.0) that partially works with the AA-3000 ZOOM. One of the biggest failures is that AntScope2 1.3.0 recognizes the AA-3000 ZOOM, but somewhere it mistranslates it as an AA-30. This means that it will only do an SWR scan from 100 kHz to 30 MHz. Kind of a bummer, but I suspect that will eventually get fixed. When connected via USB, there is no issue with scanning the full range from 100 kHz to 3 GHz, only when in Bluetooth mode. Overall I suppose I will like the AA-3000 ZOOM once I get used to the buttonolgy changes from the AA-600. It's just as well made as the AA-600 and now I can do measurements up to 3GHz. Once the bugs are addressed, this will be a fine bit of kit.

Using AntScope2, I have created .s1p calibrations files for the antenna coax feed line but I can't figure out how to apply the calibration data to the antenna sweep results to null out the feed line for a more accurate reading. Any help would be greatly appreciated.

Hello Running on Windows 10 fully updated. If I run the latest rigexpert-flash-tool v1.6.1 I get various component runtime errors The RigExpert-FlashTool v1.5.17 runs without errors., and it did update my Rigexpert Stick Pro from 1.4 to 1.5 Thanks -- Best 73 - Dave - G8LIY

I have the 650 ZOOM with firmware 1.9. In the Americas we have access on 70 CM between 430 and 450 MHz. The SWR graph only shows in the Gray area between 430 and 440 MHz. I have selected the different regions of the world to see if this changes but it does not. It looks like a bug in the firmware that only shows this 10 MHz area as being Gray but it should show Gray for the entire 20 MHz area of 70 CM Bruce N7XGR

The subject of the post doesn't really sum this up, but it's the best I could come up with. Bear with me... I'm building a 6m uniform current loop as detailed here. The loop is 0.84 wavelength total, divided into seven segments, so each segment is 0.12 wavelength. Each segment is terminated with a capacitor to offset the inductance of the length of wire, therefore, each wire+capacitor segment should be resonant at 6m. I have built this antenna before without the benefit of an analyzer. It's rather tedious to adjust (but worth it in the end!) as each segment length must be adjusted to maintain the current distribution and subsequent pattern of the antenna. I am wondering if there is a way that I could use the analyzer to measure the resonance of each segment to get them all adjusted before final assembly. Thanks in advance for any suggestions! 73, Matt, N0EYE

Found and downloaded the FTDI drivers, works fb now…..

Whats the trick to getting Antscope to connect to the analyzer? I saw somewhere something about ListRE, but I see no command like that in the Antscope directory. Also, the manual says something about pushing the up arrow button to enter PC mode, my up arrow just scrolls thru the menu?

When i try to use RigExpert Flash Tool v1.5.19 on WIN7 x64 but error message appear saying "cold not set device in boot mode". Then try-ied old version RigExpert Flash Tool v1.5.14 and device is in flashing display mode but the interface dont display serial number and unknow to firmware version. Closing the old version, starting latest version, reading and writing new firmware.Done ! Is this a BUG @Alex ???

Hello, The Stick 230 came with a "1" page "Quick Guide" in the Box I have lost it..!! Is there somewhere to Download it.?, I can find a Full Manual, but I would like the "1 Page Guide" Many Thanks... -- Best 73 - Dave - G8LIY

This fellow is looking for an explanation of phase, as reported by the RigExpert and AntScope. Could anyone here help him out? AG6CX Since I do not understand the difference between the Phase indicated on my RigExpert Analyzers and the actual phase of the antenna being measured, perhaps you can find the time to help. You already have an Aerial-51 Model 807-HD antenna. Please measure it with your RigExpert AA-230 antenna analyzer, and record your results. Please re-measure it with a proper VNA (or however it should be measured) and record the results. Please show us the difference. Extra Credit: Please explain it to Rick in simple terms with the hope that he might understand. Extra Credit-2: Is there a way to identify the true j0 of an antenna using a RigExpert analyzer? If so, please show us. Thank you. 73 - Rick, DJ0IP (Nr. Frankfurt, Germany) May the Sunspots be with Us! -- 73, Rick - DJ0IP May the Sunspots be with us!

Hi Alex, A further enhancement request for New Band 40MHz / 8M Band, 40.000MHz ~ 45.000MHz (per ADIF Spec 3.1.1) I have just received a "Innovation & Research License" to operate on 40MHz/8M Would be nice to have 40MHz/8M included in a Future Update. Many Thanks.... -- Best 73 - Dave - G8LIY

Hi, Not sure if this is the place to make a "Feature Request".? I have the "Stick 230", Excellent upgrade from my AA-35 When pressing "HAM", and cycling through the BANDS Is it possible to "add" a new BAND.? "4M" ~ 70.000MHz to 70.500MHz If this is not the right place, where is. Thanks... Dave ~ G8LIY