Re: MiniProSC sound card info for BAP 3.0.8
Hi Dinoburb,
Just to clarify, you should add a CAT cable and then you will see the USB inputs you are looking for in FLRIG.
73
David
AJ6RE
|
Re: MiniProSC sound card info for BAP 3.0.8
Hi Dinoburb,
I had the same experience, with the exact same configuration: G90, MiniProSC, Rpi mobile. I did the same thing, trying to emulate Julian's setup. In the end it turned out the addition of the CAT cable (USB) between the G90 and the Rpi was necessary. I was pulling my hair out for about 2 weeks until I figured that out.
Good luck!
73's
David
AJ6RE
|
Consider using two TNCs? One for 1200 and one for 9600? NinoTNC does both speeds and is only $30, build it yourself.
toggle quoted message
Show quoted text
On Aug 18, 2021, at 5:11 PM, Don Ritchie <dritchie@...> wrote:
I'm not even sure that this is the correct group to ask this.
we are looking for a tnc that can "switch" itself from 1200 to 9600 baud.
we know that the Kantronics 9612 ex can, but I don't really want to
spend that kind of money.
an unattended digiapeater that will digirepeat whatever it gets would be
the answer.
I also am not sure I understand the difference between G3RUH and GMSK
9600 ??
Thanks
Don, K8ZGW
|
The TNC-Pi9k6 is dual mode, and can switch modes with a few simple commands.? However, the radio is another problem, switching from 1200 to 9600 baud.
The latest PiGate software switches the TNC mode for you (if you have a TNC-Pi9k6 mounted), depending upon what RMS station you have selected for polling.
Mark KD0QYN
On Wednesday, August 18, 2021, 04:11:09 PM CDT, Don Ritchie <dritchie@...> wrote:
I'm not even sure that this is the correct group to ask this.
we are looking for a tnc that can "switch" itself from 1200 to 9600 baud.
we know that the Kantronics 9612 ex can, but I don't really want to
spend that kind of money.
an unattended digiapeater that will digirepeat whatever it gets would be
the answer.
I also am not sure I understand the difference between G3RUH and GMSK
9600 ??
Thanks
Don, K8ZGW
|
Hello Don,
There used to be a write up on NW Digital's website of how to do
this but it seems to be withdrawn.? That said, there are some
pros/cons to trying to do this and they can be found in the
archives on the Direwolf email list but here is one for you to
read:
??
/g/direwolf/topic/34951406?p=Created,,,20,1,0,0
--David
KI6ZHD
On 08/18/2021 02:11 PM, Don Ritchie
wrote:
toggle quoted message
Show quoted text
I'm not even sure that this is the correct group to
ask this.
we are looking for a tnc that can "switch" itself from 1200 to
9600 baud.
we know that the Kantronics 9612 ex can, but I don't really want
to
spend that kind of money.
an unattended digiapeater that will digirepeat whatever it gets
would be
the answer.
I also am not sure I understand the difference between G3RUH and
GMSK
9600 ??
Thanks
Don, K8ZGW
|
I'm not even sure that this is the correct group to ask this.
we are looking for a tnc that can "switch" itself from 1200 to 9600 baud.
we know that the Kantronics 9612 ex can, but I don't really want to
spend that kind of money.
an unattended digiapeater that will digirepeat whatever it gets would be
the answer.
I also am not sure I understand the difference between G3RUH and GMSK
9600 ??
Thanks
Don, K8ZGW
|
Anyone experiment around with the?iqaudio dac pro hat? ?I am looking at rebuilding my iq64 and started hooking it up. ?Looking for any lessons learned.
thanks?
Tom AE5NF
|
Re: Micropython I2S audio library?
I don¡¯t know Python but aren¡¯t microPython and ciruitPython basically the same thing?
|
Re: Micropython I2S audio library?
At this point, I really just want to make sounds. Eventually, I want to try playing .mp3s.
|
Re: Micropython I2S audio library?
Well, this is a Pico, the new, little RPi microcontroller.
|
Re: Micropython I2S audio library?
Hui Dan,
I'm curious...? ?why use Micropython on a Raspberry Pi when you can use full blown Python ?
73 - Bill KA8VIT/W8COD
toggle quoted message
Show quoted text
I'm working on a project (well, that's not strictly trure; I'm just playing around with it :) ) that's not strictly ham-radio related.It uses a Raspberry Pi Pico and a
?to produce sounds. I'm wondering if any of you are doing something similar and have perhaps found a MicroPython I2S audio library to run the thing.
73,?
Dan KB6NU
|
Cant get full screen hamclock on 7 inch touchscreen
I finally got hamclock to work, but i cant get a full screen on my ebay 7;inch touchscreen
I tried all the 4 resolutions with the make - j command and screen stays the same when i hit the up v carrot
with my mouse with all the different commands ...size stays small
i then found the rpi fullscreen command hamclock -f on, but now even with lowest resolution screen is just too big.
I looked at what i purchased thru ebay and its marked 1366x768...am i out of luck using this screen ???
thanks for help
|
Re: Micropython I2S audio library?
Hi Dan,
Are you looking for something like midi or a music synthesizer? I am interested in that, too.
73,
Bill KU8H
bark less - wag more
toggle quoted message
Show quoted text
On 8/17/21 8:39 AM, Dan Romanchik KB6NU wrote: I'm working on a project (well, that's not strictly trure; I'm just playing around with it :) ) that's not strictly ham-radio related.It uses a Raspberry Pi Pico and a MAX98357 D-A/amp board <>?to produce sounds. I'm wondering if any of you are doing something similar and have perhaps found a MicroPython I2S audio library to run the thing.
73,
Dan KB6NU
|
Re: MiniProSC sound card info for BAP 3.0.8
toggle quoted message
Show quoted text
I have been attempting to set-up a G90, MiniProSC, Raspberry Pi remote set-up and I am flummoxed (technical term) on what the MiniPro returns as the sound card.? When attempting to set-up WSJX I use the Icom 7100 as the radio and cannot figure out which of the 23 options presented.? Having tried anything the indicated a USB sound card resulted in no successful set-up.
I have the G90 set-up with VOX and I/O via LINE.? The program cannot/will not read the radio.
I¡¯ve tried Julian¡¯s set-up for FLRIG and here I cab select the Xeigu G90 but when it comes to the the sound card I¡¯m presented with over 50 options starting with ?/dev/tty, /dev/tty0 on to /tty9 then its /dev/ttyAMAO ?and ?/dev/ttyprintk.? Nothing seems to work and no data sent to the program AND the USB audio switch is grayed out under the XCVR Configuration!
i need help in getting out of this rabbit hole!
|
Micropython I2S audio library?
I'm working on a project (well, that's not strictly trure; I'm just playing around with it :) ) that's not strictly ham-radio related.It uses a Raspberry Pi Pico and a ?to produce sounds. I'm wondering if any of you are doing something similar and have perhaps found a MicroPython I2S audio library to run the thing.
73,?
Dan KB6NU
|
Re: MiniProSC sound card info for BAP 3.0.8
Most of the BAP users running the G90 hang out in this forum /g/KM4ACK-Pi/topicsI don't own the MiniProSC but I believe it is similar to the Signalink. Look for the sound card that has "Codec" in the name. 73, de KM4ACK
|
Re: MiniProSC sound card info for BAP 3.0.8
I would suggest getting a terminal window up, and typing aplay -l and seeing what you get, and then arecord -l and looking at the output from that. ? The output can still take a bit of deciphering, but it will hopefully give you a better idea of what to look for for your USB Audio. ? 73 Phil 2E0HGU
|
MiniProSC sound card info for BAP 3.0.8
I have been attempting to set-up a G90, MiniProSC, Raspberry Pi remote set-up and I am flummoxed (technical term) on what the MiniPro returns as the sound card. ?When attempting to set-up WSJX I use the Icom 7100 as the radio and cannot figure out which of the 23 options presented. ?Having tried anything the indicated a USB sound card resulted in no successful set-up.
I have the G90 set-up with VOX and I/O via LINE. ?The program cannot/will not read the radio.
I¡¯ve tried Julian¡¯s set-up for FLRIG and here I cab select the Xeigu G90 but when it comes to the the sound card I¡¯m presented with over 50 options starting with ?/dev/tty, /dev/tty0 on to /tty9 then its /dev/ttyAMAO ?and ?/dev/ttyprintk. ?Nothing seems to work and no data sent to the program AND the USB audio switch is grayed out under the XCVR Configuration!
i need help in getting out of this rabbit hole!
|
Good luck and try not to jump to conclusions about the feasibility of an OS too soon... in many cases, the problem is the user.
73 de heinz, VK2STM
|
Re: RealVNC loses connection
Mark, David:
Thanks for your help.
I found something on the web last night about 2.4g wifi issues maybe being caused by HDMI cables.
In the living room to TV, I am running HDMI this is where I did the initial startup of PI when I unboxed it.? In the radio room, its headless.
So I went to 5G, connected direct, ran a ping back to the router, while in the living room.? Ran realvnc viewer from my phone.? Twenty minutes without a drop, changed to cloud, another 20mts without a drop.? Back to the radio room, now the router is 7ft away.? Wired up for FT8 ran on cloud, ran ping to the router.? In 30mts of running FT8 with a few contacts, not a single drop.
Before I went to 5G, on my desktop or phone I would see the ping stop when it dropped connection.?
Been running on cloud, FT8 for 30mts thing morning, no drops.
I will run the data test both of you suggested after work on both 5G and 2.4G
Thanks
Carlos
KE5DFK
|
Tadd KA2DEW in NC
Dave R
km4ack
henry post