Re: Help with TNC9k6 setup
|
Mark Griffith
Don, If you will be using the PiGate image, there is nothing for you to do except plug the TNC into the Pi, load the image to an SD card, insert it about boot. I don't know how the TNC-Pi9k6 from WVARC comes configured, you should talk with them, but the procedures to setup the board in the doc I attached are correct.? I don't currently support that particular board, but probably will in the near future. Mark KD0QYN
On Friday, June 26, 2020, 1:54:19 PM CDT, Don Munson <w4gfq@...> wrote:
Two Dons ¨C go figure ? ? I use Putty as SSH as well as VNC ¨C which is why I was sort of curious why turning off Secure Shell seemed to work as I didn¡¯t connect that way.? Unless it reserved it somehow? ? I got my 9k6 from WVC ARC via Etsy.? I saw the Coastal site.? That is where (I believe) I go the ¡®manual¡¯ to follow that was the TNC-Pi originally.? I did find a link I had stuck away (and forgotten) to a ¡®manual¡¯ to assemble the WVC board.? That had some additional information in it as well.? That was here: ? And your PiGate site was the genesis of my intent to get packet working in my Go Kit ?? Easy and smooth operation with my V71A to a WinLink node was appealing ¨C but there were NO TNC boards except the 9K6 available.? And since the V71A can do 9600 I said WTH ¨C another arrow in the quiver in addition to standard 1200. ? My hang up at the moment is the WVC manual which states (implies?) that the Teensy board needs to be loaded with software.? I need to read and digest that a little bit to figure out what that means.? But at the moment all I have ¡°loaded¡± directly is the Pi itself.? I did see later in this string (or earlier in time) about the AX25 files and I have to go see if those are on the board or not.? ? It will be steps but as long as I know the steps I should be OK overall.? The challenge to me is finding and understanding the steps ? ? Don, W4GFQ ? From: [email protected] <[email protected]> On Behalf Of Mark Griffith via groups.io
Sent: Friday, June 26, 2020 11:51 AM To: [email protected] Subject: Re: [RaspberryPi-4-HamRadio] Help with TNC9k6 setup ? Don, ? When you connect through PuTTY, is is through an SSH or Secure Shell TCP/IP connection port, not serial.? VNC is also through a direct connection at a non-serial port. ? Where did you get the TNC-Pi9k6 from?? I've attached the docs from the old Coastal Chipworks site.? The board and procedure to build it is a little different than the other people selling this board, but the firmware configuration docs are still correct. ? I'm getting ready to make a change in my website to reflect that the TNC-Pi9k6 is the choice for both the PiGate and PiGate RMS devices.? Is is a drop-in replacement for the TNC-Pi2.? I'm not too happy with the progress MFJ is making with building the new TNC-Pi3 board, and the West Virginia group that is now selling the TNC-Pi9k6 as an assembled board has a great price, which is probably going to be close to what MFJ sells the 1200 baud only board for. ? Here's my web site in case you are interested in using your Pi and the TNC for communications with Winlink2000. ? Mark KD0QYN ? ?
?
? ? ? Let me know if you have any more questions. ? Mark KD0QYN ? ? ? On Friday, June 26, 2020, 6:58:46 AM CDT, Don Munson <w4gfq@...> wrote: ? ? EXCELLENT!!? ? So after six tries because it is early and I simply can¡¯t type (and I have learned Linux is very unforgiving on typing!) I got the following: ? Using Serial Port /dev/serial0? retrying ? and a presentation of the parameters.?? ? Now at least I know they are talking to each other ? ? I am not sure why it worked but it did.? I am going to presume that somehow the putty connection to the pi was using the serial port?? Although how it still connects (as does VNC) confuses me ¨C but no matter. ? The obvious next question is where do I go from here for reading about how to configure and use this board? ? Don, W4GFQ ? From: [email protected] <[email protected]> On Behalf Of Mark Griffith via groups.io ? Don, ? First, you'll also need to use the raspi-config utility to enable the console serial port, but disable console login. ? Run "sudo raspi-config" ? Then go to menu 5, Interfacing Options, then menu P6, and disable the login shell over the serial port. ? On the next screen, keep the serial port enabled. ? Save these and finish. ? Now try "sudo pitnc-getparams /dev/serial0 0" ? This works the same with the TNC-Pi2 or the TNC-Pi9k6 and will be the same with the TNC-Pi3 once MFJ starts selling them. ? Mark KD0QYN ? ? On Friday, June 26, 2020, 1:01:22 AM CDT, Don Munson <w4gfq@...> wrote: ? ? First I am an operator and not a technician.? I can follow directions and to some extent do enough to get myself in trouble.? Having said that I purchased a TNC9k6 and have it running wiht a Raspberry PI 3B+.? Followed directions at (downloaded the pitnc files, set them in the directory and set permission to execute by owner.? Verified with ls -l that all permissions and owner/group ids as well as my logge din user are all setup per the text. |