Hi?
I've just installed QnetGateway on a pi to replace a dead icom G2 Install that had ircddb. I've configured it for ircddb , and entered the correct login and password info for ircddb.?
However I noticed that on the ZL2VH ircddb status page?
the irc status is green but the both module B and C status is red, along with no lastheard info.
The system communicates with the repeaters ok and I can link and unlink successfully.
Wonder if anybody has any ideas. Should I be using openquadnet ?
73's
Simon ZL2BRG

开云体育

Hi Simon,

Your the first to connect an Icom stack to ircddb.net using QnetGateway, so I'm not sure what the problem is with the two modules. Are the frequencies and other data for the modules okay? I would be happy to provide a fix, if I knew what to do. Someone from ircddb.net needs to help and let us know how to get things green. I suspect I'm malforming or missing an IRC message to the IRC server.

You can, of course, switch to rr.openquad.net. I think we more completely support routing, especially group routing. Of course if you have users that are callsign routing or repeater (zone) routing to nodes on ircddb.net, they won't be able to do this if you move to rr.openquad.net.

Tom

Hi?
I've just installed QnetGateway on a pi to replace a dead icom G2 Install that had ircddb. I've configured it for ircddb , and entered the correct login and password info for ircddb.?
However I noticed that on the ZL2VH ircddb status page?
the irc status is green but the both module B and C status is red, along with no lastheard info.
The system communicates with the repeaters ok and I can link and unlink successfully.
Wonder if anybody has any ideas. Should I be using openquadnet ?
73's
Simon ZL2BRG

-- 
___________________________
73
n7tae (at) tearly (dot) net

开云体育

Hi Simon,

?

In respect to configuring for 2 IRCDDB networks, this URL may be apropos.

?

?

?

?

Regards

开云体育

Just to make it clear, this is for configuring Jonathan Naylor's ircDDBGateway, not QnetGateway.

It was made clear to me in my discussions with the admins at ircddb.net that they don't want clients simultaneously logged into both ircddb.net and QuadNet. I'm not going to defend their position, but I am going to respect it. Therefore both QnetGateway and the SmartGroupServer does not support simultaneous logins.

Hi Simon,

?

In respect to configuring for 2 IRCDDB networks, this URL may be apropos.

?

?

?

?

Regards

-- 
___________________________
73
n7tae (at) tearly (dot) net

Yes.

开云体育

Hi Simon,

I appreciate your comments. As stated elsewhere, I don't support simultaneous irc networks.

I haven't spent much time thinking about a dashboard. There is a branch that has a VERY minimal control dashboard, but nothing much has happened with it since it was first pulled.

If a full dashboard is important, I suggest you look at PiStar. You'll need to switch from MMDVM to DStarRepeater. From there you should be able to configure your Icom Stack.

I'm not sure how recently Andy Taylor has updated ircDDBGateway, but if it's relatively recent, you might also be able to connect to multiple irc networks as Jonathan's newest ircDDBGateway supports this.

Tom,Joe

Thanks for the replying. Think I setup ircddb correctly. I copied the data from the old config.?

Joe, the G2 PC died. The QnetGateway is on the same local network IP as the original G2 PC, so all the existing port forwarding I have setup should still be ok.

Tom: is there a way to run both openquadnet and ircddb at the same time ?.?

The other issue I can see users complaining about is the lack of a dashboard.

Thanks for your help

73's

Simon
ZL2BRG

-- 
___________________________
73
n7tae (at) tearly (dot) net

Thanks for help folks.?
Running both ircddb and quadnet is a not a requirement. however I do think a dashboard is essential, users want to know who or what is connected to the gateway.
Colby is assisting me in diagnosing the ircddb issues. Thanks Colby :)
73's
Simon ZL2BRG