开云体育

Thank you.

HI Colby, Hi hot spot stoppped. It was probably on his side. Do you want me to open the ssh so you maybe able to go back when you have the chance, about the smart quad?

Looking at the logs: 2018-09-09 19:02:09 12.68s: 0%: 0.0% N0MIS___/ID51 XRF072AL N0MIS__B N0MIS__G XRF072_A 2018-09-09 19:02:29 7.66s: 0%: 0.0% N0MIS___/ID51 XRF072AL N0MIS__B N0MIS__G XRF072_A

Were you both using the CQCQCQ use reflector? That is the same as for a repeater if you were trying a local QSO to the repeater. Colby Sent: Sunday, September 9, 2018 15:01 To: [email protected]

Hi Colby, We were testing and having a qso, but we could not hear each other.

Norm give me a call at 2073314368 Colby Sent: Sunday, September 9, 2018 13:44 To: [email protected] Subject: Re: [QnetGateway] Failure on Qngateway Service Hi Colby, Transmitted more than once at

Hi Colby, Transmitted more than once at QW1BSB. Did you copy the voice?

I can hear you, you aren’t hearing me though so something is still awry with the setup. DO you have all the necessary port forwards in your router configured to go to the gateway machine? Colby

I can hear you keying it up, try saying something. Leave it in your UR field at all times Colby Sent: Sunday, September 9, 2018 13:37 To: [email protected] Subject: Re: [QnetGateway] Failure on

I entered the "QW1BSB" on the direct input(UR) and ptt twice. nothing happens.

I can hear you keying it up, but not hearing any voice. Leave QW1BSB in your UR Field and try talking. Colby Sent: Sunday, September 9, 2018 13:25 To: [email protected] Subject: Re: [QnetGateway]

Put QW1BSB in the UR field of your radio you’re using to communicate with your ICOM repeater. You may have to key it twice to get it to subscribe, it should come back with a confirmation tone once

Hi Colby, I just connected to the XRF072A reflector and transmit. It is working, thank you so much.Now I need someone transmit and start a qso.

Give me a few minutes. I'm not at my computer. But yes you can safely comment out the IP addresses in the config. The defaults work out of the box. Send me the output of the route command too please.

Hi Colby, Run it again and here is the result. It has stopped. Do you want me to return the # on all the IP on qn.cfg? root@nolyn78dell:/home/nolyn1978/QnetGateway# systemctl restart qngateway qnlink

You can comment out the IP addresses in qn.cfg, as the defaults just plain work. Colby Sent: Sunday, September 9, 2018 12:49 To: [email protected] Subject: Re: [QnetGateway] Failure on Qngateway

Hi found the error I just change the IP back to 172.16.0.20, I made an error and entered 172.16.0.1. Let me run again.

HI Colby, root@nolyn78dell:/home/nolyn1978/QnetGateway# ip a 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1 ??? link/loopback 00:00:00:00:00:00 brd

Actually, I think I know what might be wrong. Restart the server, I think more than one instance of qngateway is running causing a bind issue. Reboot the server, and when it comes back up, type

Show me ip a and /etc/network/interfaces again Colby Sent: Sunday, September 9, 2018 12:34 To: [email protected] Subject: Re: [QnetGateway] Failure on Qngateway Service Hi Colby, It is working.