开云体育

Hi Colby, It is working. Except it say "can't open 172.16.0.20:2000" and "Failed to bind 172.16.0.20". I do not know how to stop the so I could copy the rest.

Nomis Put a # at the start of line 117, the qnvoice one, and see if it’ll boot. If it will, I can help you prune your qn.cfg file down to what it only needs so its much easier to read. What Tom is

HI tom, Thank you for telling me. I was not aware that I can leave the #, comment on most of them. Just be to clear or as I understood what you provided. 1. Return the # as before. 2. Login enter

Put a # in front of line 117 (this line: qnvoicefile = /tmp/qnvoice.txt), then do systemctl restart qngateway qnlink Alternatively you can put “ before /tmp and after qnvoice so it reads qnvoicefile

Hi Nomis, You're qn.cfg file is way too complicated, so it's hard to see what you've done. The example files I supplied, especially qn.everything.cfg and qn.icom.cfg define all of the config

Hi Colby, here is the result. root@nolyn78dell:/home/nolyn1978/QnetGateway# systemctl restart qngateway qnlink ; journalctl -u qngateway -f -- Logs begin at Sat 2018-09-08 23:50:18 PDT. -- Sep 09

Same with the C module, there is a } right under the line # url = "github.com/n7tae/QnetGateway" that needs a # before it, but not the 2nd one. The 2nd one is required to close the modules section.

Tom pointed out (as I missed) there must be a # before the } above the b = { Make that change and do systemctl restart qngateway qnlink ; journalctl -u qngateway -f Things should start working. Let me

Its done.

Actually, this is much easier. Use this qn.cfg (I made all the edits) # Qnet Gateway Configuration ircddb = { login = "KM6VLB"; # login callsign for the ircDDB network host = "rr.openquad.net" # other

And “feet” after agl. Sent: Sunday, September 9, 2018 11:34 To: [email protected] Subject: Re: [QnetGateway] Failure on Qngateway Service Hi Colby, Here is the qn.cfg file. # Qnet Gateway

Also, remove MHz after the frequency. Sent: Sunday, September 9, 2018 11:34 To: [email protected] Subject: Re: [QnetGateway] Failure on Qngateway Service Hi Colby, Here is the qn.cfg file. # Qnet

On line 54 (nano +54 /usr/local/etc/qn.cfg, remove “miles” after 15, it can only be a number. Then, save and exit, and do systemctl restart qngateway qnlink ; journalctl -u qngateway -f and watch

Hi Colby, Here is the qn.cfg file. # Qnet Gateway Configuration ircddb = { ??????? login = "KM6VLB";???? # login callsign for the ircDDB network ??????? host =

Ok. Send me your qn.cfg file.

HI Colby, Good Morning. Here is the output. *root@nolyn78dell:/usr/local/bin# ./qngateway /usr/local/etc/qn.cfg VERSION QnetGateway-7.0.1 Reading file /usr/local/etc/qn.cfg Parse error at

Type cd /usr/local/bin and enter the following command: ./qngateway /usr/local/etc/qn.cfg Provide the output here please, thanks – Colby Sent: Sunday, September 9, 2018 01:01 To:

Hello, I was able to set up the IP address for the 2nd NIC, as shown below "enp4s0". Ping Gateway 172.16.0.20 and controller 172.16.0.1 all okay. But failed qngateway.service shown below. Anyone could

Hi Colby, Good morning. Here is the info on the etc/network/interfaces. I will in and out from my computer room, doing honey do's? on the weekend and make sure my radio privileges is not taken

Show me your /etc/network/interfaces Enp4s0 has no ip address assigned to it, so this will have to happen before your setup will work. This typically takes place in /etc/network/interfaces so send me