Re: Close to Success... Need id-51 help I think
|
Correct matters not if you are using Pi-Star or Qnetgateway to the radio. You program the same only the open spot is different.. and even with the open spot if you program the radio the same. It works.. It is just "over kill". But qntetgateway wants Rpt-1 and Rpt-2 same as Pi-Star does.. from a "Radio side" viewpoint they work the same (Some serious differences from other viewpoints but the radio is set up the same way) "Nothing adds excitement like something that is none of your business" Note I am not a doctor, I don't even play one on television John F Davis On Thursday, June 11, 2020, 07:31:02 AM EDT, Dale L Puckett <dale.puckett@...> wrote: Thanks John! Unfortunately, I am using QnetGateway as a HotSpot. My ID-51 does not have terminal or access point mode. It is older model. 73? On June 11, 2020 at 5:58:54 AM, John F Davis (wa8yxm@...) wrote:
Dale are you useig Qnetgateway as a HOTSPOT or are you usingITAP (Icom Terminal, Access Point) I use ITAP with my ID-51A+2There is no "Memory entry" for the Terminal mode sine there is noradio For use with other than the Open Spot hot spot I have MY CALL onthe ID-51 set to.. Well MY CALL Rpt1 is My Call and a module number (The Terminal is Module T forTerminal but that's not in the radio. only in Qnet) Rpt1 is thesame as the Hot-spot's D-Star config IE WA8YXM B And RPT2 is always "G" WA8YXM G (NOT sure about the space RT willdeal with that)... RT may force the hotspot into SKIP mode if it'sa simplex hotspot. Since I program in DR mode the UR field is usually populated viaradio menu as CQCQCQ (The display says USE REFLECTOR by the wayMore on that in a line or 3 IF I want to use DSTAR1 or 2 It's in YOUR CALL memories (Also theTerminate command DSTAR1 T and DSTAR2 T) and I just selectthem. What is the difference between "Local CQ" and Use Reflector? RPT2is not sent when using Local CQ so it will not go out over thegateway Only on USE REFLELCTOR or GATEWAY CQ is the RPT2Sent. This is the importance of RPT2 with a other than open spot hot spot(Open spot assumes RPT2) This is not the method for the other (Regular) memories "Nothing adds excitement like something that is none of yourbusiness" Note I am not a doctor, I don't even play one ontelevision John F Davis On Thursday, June 11, 2020, 02:23:51 AM EDT, Dale L Puckett<dale.puckett@...> wrote: Thank you to Tom, Colby and John for you assistance. I'm still fighting these issue trying to get my ID-51 running withthe Qnet Gateway. My RT Systems programming software won't save an entry with out aCallsign in the repeater 1 position... and when I try to transmitafter entering a callsign there I get this in the gatewaylog: Jun 11 00:43:52 raspberrypi-qnet qngateway[416]: MYCALL [K0HYD? ] failed IRC expression validation I was able to link to Reflector 30C using the Send UR Call field inthe QnetGateway Dashboard. I can also unlink there. After linkingto 30c this way I was able to listen to QSO's. But when I try totransmit using the Use repeater entry with CQCQCQ I get the messageabove. Here are a few lines from the link log after linking thisway: Jun 11 00:46:31 raspberrypi-qnet qnlink[429]: Connected to callREF030 Jun 11 00:46:32 raspberrypi-qnet qnlink[429]: Login OK to callREF030?? mod C Jun 11 00:46:33 raspberrypi-qnet qnlink[429]: sendingFile:[/usr/local/etc/linked.dat], mod:[B], RADIO_ID=[LINKED REF030C???? ] It appears in the gateway log that the subscribe to DSTAR2 alsoworks from the Send UR Field. But if I try to Subscribe or Linkfrom the radio I get the failed message above. Here is my entry inthe RT Systems Programmer: I also used K0HYD? B in that field following the directions ofa YouTube video from K9WLW. I get the same error with both entries.Here's the My Callsign entry form with the UR Callsigns that gointo the "To:" field: I had to enter the data for the MYDVAP repeater using the radio'ssoftware as RT Systems Software woudn't save the entries. I'm hoping there are some ID-51 users out there using QnetGatewaythat can help. Thanks again for all the help so far. 73 -- Dale L Puckett K0HYD Goddard, KS 67052 Member Society of Professional Journalists -- Dale L Puckett K0HYD Goddard, KS 67052 Member Society of Professional Journalists |