开云体育

Hi all SSB firmware was released into beta on 17-Mar-2025 after 9+ months of development. Many thanks to everyone who bravely helped test it and patiently provided their feedback and observations. There are now quite a few YouTube videos, forum reports and other social media mentions about on-air successes with QMX SSB. Now that it has been at least 6 weeks in beta and I believe most of the issues have been resolved, it's time to promote it to an official version. I have called this version 1_02_000 and published it on the QMX page http://qrp-labs.com/qmx where I have also published the updated operating manual, which grew from 111 pages to 134 pages. The main changes are: SSB (obviously!) including CESSB, TX Equalization, Mic AGC, VOX, Pre-distortion and and and... Addition of up to two more USB Virtual COM serial ports (up to three total). All of the hardware tests such as RF and SWR sweep, and Diagnostics, are now available on the LCD too. New CAT commands for LCD contents, S-meter, AGC-meter, Power meter, SWR meter, SSB source Complete list (relative to 1_00_027 the previous official version): SSB modes added (USB and LCB), with CESSB, TX Equalization, Mic AGC, VOX, Phase pre-distortion and more Rationalization of menus, grouped into CW, Digi and SSB submenus (now Keyer and Decoder are submenus of CW) Added up to two more USB Virtual COM serial ports (configurable) LCD versions of AF, RF, Image, LPF, Test ADC I/Q sweeps (miniature graph on LCD) New function PA mod. test to check operation of amplitude modulator Diagnostics screens are now available on the LCD interface too Now remembers previous menu location on ALL menus regardless of nesting level Add way of forcing factory reset, press Menu (left) button during power-up Change TX color in diagnostics screen from red to blue, to avoid confusion since red things are errors Added CAT LC command to retrieve LCD contents Added CAT commands SA (AGC meter), SM (S meter), PC (Power meter), SW (SWR meter) Added CAT command SS (get/set SSB input source) Bug fix: PTT P did not work properly Bug fix: Incorrect PA voltage display on the Diagnostics screen 73 Hans G0UPL http://qrp-labs.com https://www.buymeacoffee.com/g0upl

(Right: Gerald Youngblood, Flex Founder) They launched their new product "Aurora", 160-6m, 500W transceiver that uses polar modulation just like QMX Hans: "So they visited me to admire QMX and I visited them to admire Aurora" https://www.facebook.com/share/p/1Brw3LK9zY/ 73 DE muhsin TA1MHS

Received the kit from FedEx in a perfectly intact box. The content check was positive with the exception of the L501 inductor with the partially broken edge. Can this defect affect the operation of the kit?

Hi, I’ve had my QMX+ for a number of months and had tested the then beta now regular SSB firmware with good results except pretty low output power in SSB. As I had never gotten around to fine tune the LPFs when building it I decided this was the logical next thing. So I fiddled with spreading and compressing turns on the toroids and managed to get all bands to between 4 and 5w output for CW except 160m that was already at 6w. Running 12.0v input and build for 12v Being happy with results I then first tested resetting to factory defaults, and then tested SSB output power. Still max 2-2.5w according to the Bird. I then decided to run the SSB calibration again. Worked fine til perhaps 12m or 10m phase. I then heard some terrible noise from the speaker and saw the QMX crashing with all blocks in the display and turning itself off. I tried powering on again, but won’t start now. Just blank display and current protection on PSU kicks in due to over current. I suspect maybe finals are fried with internal short as result? Jonas 7 maj 2025 kl. 23:12 skrev Stan Dye via groups.io <standye@...>: ? On Wed, May 7, 2025 at 01:38 PM, Wiggle Pig wrote: It’s D503 and D504 These are placeholders for diodes that could be placed across the BS170 outputs, as was commonly done with QDX. Hans included them in the design, but has not encouraged installing the diodes, which he believes are unnecessary for QMX. They may suppress spikes, but they also add additional capacitance to the PA, which may affect it adversely in other ways. There were many posts on this list regarding this topic a year or so ago. Stan KC7XE

I plan to build a QLG2 GPS Receiver Module to use it with my QCX+ I will add: - the blue LCD accessory kit; - the Customized case kit (enclosure). I guess I will have to order it with the "Front blank cut/drilled plate. But what rear plate will I have to order? I might better build the Clock kit with its enclosure and the QLG2 GPS but will the GPS be inside the Clock enclosure? 73 - Pierre - FK8IH

Hello. I'm assembling a 50 watt power amplifier for use with a QCX+ that I assembled last month, for the 80 metre band. I have very high harmonics at the output of T3 - as a result, I get only about 9.3 watts out when running at 13.8 V. Output from the LPF looks OK on the 'scope. I found the excellent videos by NA5Y which shows the output of T3 should be much closer to a sinusoid than what I get. I also found the discussion with KO1KR in August of 2020, but unfortunately I can't see his scope photos so I don't know if he had the same problem. I've since skimmed through the many discussions on this forum but haven't found the same issue exactly, though I did check out some of the suggestions given here. I found the amplifier took 67 mA with R5 fully CCW - I adjusted R5 till the amplifier drew about 70 mA with the QCX+ key-down in practice mode. Here are my scope traces: 0092 is the gate drive, yellow is Q1 gate, purple is Q2 gate - all is well here. 0090 is the drain voltage, Q1 in yellow and Q2 in purple - these look like there is oscillation ? 0091 is the voltage at the output of T3. This has a lot of third harmonic and doesn't look like the waveform NA5Y showed at this point. (QCX+ was set for 3.520 MHZ , amplifier connected to a dummy load.) I thought that perhaps my bench power supply is doing something odd when the amp is drawing power, but I probed the 12 volt line right at the barrel connector and the 'scope showed almost no disturbance of the +12 v supply. In frustration, I observed the output of T3 with the 'scope set for a long capture - it almost looks as if the distortion grows with time, for the first few tens of microsceconds the scope showed a small but sine-ish waveform, which over the span of a few hundred microseconds got wigglier and wigglier till it developed into the mess seen in my scope capture 0091. I've checked DC continuity to the windings of all the transformers and coils. I did find a bad joint on the primary of T1 but I cleaned it up and can now get power out of the amplifier. I haven't yet checked bias on all the 1N4007 diodes but the input looks quite sinusoidal at R3 closest to the input. The few watts the amplifier does produce look OK at its output. The QCX+ makes about 4.3 wats into a dummy load (43 V peak to peak) at 13.8 V DC. I'm assembling these units for a friend, and I had really hoped to have them ready for Field Day this year. The instructions are excellent and I have followed them closely. What can I look at next? Bill VE4STW

Does anyone use Solder pots for tinning and removing the enamel from the toroid leads? Any hints and tips? I see a cheap one on Amazon for about $20. Any suggestions if I should buy special solder for this, or use my normal Kester 63/37 solder in it?

Hello everyone, I've seen in different topics that T507 solder joints should be checked & reflowed in the event of a high SWR spike on SSB transmit... a problem that several of us have mentioned, and in my case, makes the rig completely unusable on SSB. I do understand, looking at the schematic, how this could cause the protection circuit to trigger. What I do not (yet) understand is why this would be a problem that I see on SSB only, and not on CW. I have not witnessed this on CW. A theory I have is that maybe if the joint is just on the edge of continuity, then a higher duty cycle CW signal would temporarily "anneal" the bad joint, but that on SSB you don't have that effect. I am a skeptic about my theory...in any case, I do plan on trying reflowing T507 and associated circuitry. This was a factory assembled unit so I was hoping to avoid this, but I appreciate all that Hans is doing. I'm not complaining at all... just looking for guidance and thoughts so I can get this amazing rig on SSB. God bless, Joel W9JFK

When Elecraft introduced the KH1 a year ago, I was immediately enthusiastic about the concept. A small and lightweight shortwave radio with an integrated telescopic antenna. This means that, weighing less than 400g, it can be used in any suitable location on shortwave. So I wanted to build something myself. I immediately began my own experiments with telescopic antennas for 7-30 MHz. This confirmed that a counterweight is absolutely necessary. This wire, which is a quarter of the wavelength long, contributes significantly to the radiated energy. So the idea arose to forgo the telescopic antenna and experiment with end-fed wires twice the length. Of course, it makes sense to stretch the wire as high as possible. But I also got respectable reports with EFHW lying on the ground or in bushes. In this place the antenna may detunes itself, so a tuner is necessary, as well as the standard 1:64 transformer (Unun). The tried-and-tested resonance circuit (Fuchs Kreis) performs both tasks. Once the antenna issue was resolved, QRP Labs brought out the QMX. The ideal TRX for my projects, and now even capable of SSB. Now all that was missing was a suitable housing with an integrated battery and a speaker with an amplifier. Then a paddle for CW as a contactless touch key directly on the device. And the QMX Carrot was finished. But it wasn’t that simple, because everything had to be as small and light as possible. It now weighs 340g and measures 15x8.5x3.0 cm. I’m happy with that. 73 Chris https://youtu.be/0kksiWVOtnQ

I'm in the midst of assembling my 2nd QMX+ and I just busted one of the Shiny Black T37-10 Toroid Cores... DAGNABBIT!!!! So, where's the best place to by only one or two Toroid cores in the US? 73, -Ed, WG5F- Tulsa, OK

I'll start by saying I think if this as a "nice to have" change: I use a manual antenna tuner and the built in SWR bridge is great for checking the state-of-tune. In a (my) "perfect world", the "Tune SWR" would present a full width, bottom line, bar graph of the VSWR, rather than a single number. It's hard (for me) to spin the tuning knobs looking a flickering numbers. Just a thought. Thank you Hans for producing such a great radio! -- 73, Brent DeWitt, AB1LF Milford, MA

I need to order some parts from Digikey. I though it would be good to order some backup parts for the QMX+. Besides BS170's what are the components that fail most frequently? Also if you have specific digikey part numbers or names that would be great, ss some of the part names match multiple items.