开云体育

Hi all SSB firmware was released into beta on 17-Mar-2025 after 9+ months of development. Many thanks to everyone who bravely helped test it and patiently provided their feedback and observations. There are now quite a few YouTube videos, forum reports and other social media mentions about on-air successes with QMX SSB. Now that it has been at least 6 weeks in beta and I believe most of the issues have been resolved, it's time to promote it to an official version. I have called this version 1_02_000 and published it on the QMX page http://qrp-labs.com/qmx where I have also published the updated operating manual, which grew from 111 pages to 134 pages. The main changes are: SSB (obviously!) including CESSB, TX Equalization, Mic AGC, VOX, Pre-distortion and and and... Addition of up to two more USB Virtual COM serial ports (up to three total). All of the hardware tests such as RF and SWR sweep, and Diagnostics, are now available on the LCD too. New CAT commands for LCD contents, S-meter, AGC-meter, Power meter, SWR meter, SSB source Complete list (relative to 1_00_027 the previous official version): SSB modes added (USB and LCB), with CESSB, TX Equalization, Mic AGC, VOX, Phase pre-distortion and more Rationalization of menus, grouped into CW, Digi and SSB submenus (now Keyer and Decoder are submenus of CW) Added up to two more USB Virtual COM serial ports (configurable) LCD versions of AF, RF, Image, LPF, Test ADC I/Q sweeps (miniature graph on LCD) New function PA mod. test to check operation of amplitude modulator Diagnostics screens are now available on the LCD interface too Now remembers previous menu location on ALL menus regardless of nesting level Add way of forcing factory reset, press Menu (left) button during power-up Change TX color in diagnostics screen from red to blue, to avoid confusion since red things are errors Added CAT LC command to retrieve LCD contents Added CAT commands SA (AGC meter), SM (S meter), PC (Power meter), SW (SWR meter) Added CAT command SS (get/set SSB input source) Bug fix: PTT P did not work properly Bug fix: Incorrect PA voltage display on the Diagnostics screen 73 Hans G0UPL http://qrp-labs.com https://www.buymeacoffee.com/g0upl

I'll start by saying I think if this as a "nice to have" change: I use a manual antenna tuner and the built in SWR bridge is great for checking the state-of-tune. In a (my) "perfect world", the "Tune SWR" would present a full width, bottom line, bar graph of the VSWR, rather than a single number. It's hard (for me) to spin the tuning knobs looking a flickering numbers. Just a thought. Thank you Hans for producing such a great radio! -- 73, Brent DeWitt, AB1LF Milford, MA

After a few days of work I completed my new QRP-Labs Xcvr after having built several years ago a Hi Band QDX. It was a real pleasure, no surprise due to an excellent manual and the adjustement and alignment were done today without dificulty. Next step will be to connect it to my Alexloop antenna. To be sure the 6 aft connectors whould slide nicely into the holes of the back plate I had screwed this plate to the lower enclosure and slid the main PCB each time I added a connector to check its position before finishing to solder it. The first difficulties I faced were to fit the LCD module and the front panel PCB to the Front panel of the enclosure : I had to cut slightly the nylon nut close to the potentiometer and I could not put in place the other nylon nut close to the encoder, I just left it near the hole in order to keep the good distance between the LCD board and the front PCB. The Last difficulties happened when I wanted to slid the main PCB inside the enclosure after having put in place the four 12MM spacers which hold the dev kit, the nylon screws below did not slide easily and I had to push quite strongly the PCB inside the enclosure. WELL I'M HAPPY WITH THIS WONDERFUL KIT AND I'M GRATEFUL TO HANS FOR THIS NICE DESIGN.

Hello. I'm assembling a 50 watt power amplifier for use with a QCX+ that I assembled last month, for the 80 metre band. I have very high harmonics at the output of T3 - as a result, I get only about 9.3 watts out when running at 13.8 V. Output from the LPF looks OK on the 'scope. I found the excellent videos by NA5Y which shows the output of T3 should be much closer to a sinusoid than what I get. I also found the discussion with KO1KR in August of 2020, but unfortunately I can't see his scope photos so I don't know if he had the same problem. I've since skimmed through the many discussions on this forum but haven't found the same issue exactly, though I did check out some of the suggestions given here. I found the amplifier took 67 mA with R5 fully CCW - I adjusted R5 till the amplifier drew about 70 mA with the QCX+ key-down in practice mode. Here are my scope traces: 0092 is the gate drive, yellow is Q1 gate, purple is Q2 gate - all is well here. 0090 is the drain voltage, Q1 in yellow and Q2 in purple - these look like there is oscillation ? 0091 is the voltage at the output of T3. This has a lot of third harmonic and doesn't look like the waveform NA5Y showed at this point. (QCX+ was set for 3.520 MHZ , amplifier connected to a dummy load.) I thought that perhaps my bench power supply is doing something odd when the amp is drawing power, but I probed the 12 volt line right at the barrel connector and the 'scope showed almost no disturbance of the +12 v supply. In frustration, I observed the output of T3 with the 'scope set for a long capture - it almost looks as if the distortion grows with time, for the first few tens of microsceconds the scope showed a small but sine-ish waveform, which over the span of a few hundred microseconds got wigglier and wigglier till it developed into the mess seen in my scope capture 0091. I've checked DC continuity to the windings of all the transformers and coils. I did find a bad joint on the primary of T1 but I cleaned it up and can now get power out of the amplifier. I haven't yet checked bias on all the 1N4007 diodes but the input looks quite sinusoidal at R3 closest to the input. The few watts the amplifier does produce look OK at its output. The QCX+ makes about 4.3 wats into a dummy load (43 V peak to peak) at 13.8 V DC. I'm assembling these units for a friend, and I had really hoped to have them ready for Field Day this year. The instructions are excellent and I have followed them closely. What can I look at next? Bill VE4STW

Hello everyone! I think this is my first post in the forums and I wanted it to be a good one. I've been thinking about a good cover for the QMX+ since i pack very compact, but don't want my QMX+ frontpanel to be destroyed. So i came up with the 3D-model below. I'd love if you like the model and come with suggestions. I am open to modify or add versions as needed! https://www.printables.com/model/1300629-qmx-frontcover-stand-and-storage The panels are all dual-sided and can be put on the front or back of the QMX+. Below are some photos:

A completely different approach to the HTML console published on this forum but as I use Flrig to control my rigs and flrig does not support Hans' excellent recent additions to the CAT codes, I am developing a widget which supplements flrig. Currently, this allows for the selection of new modes, indicates the LCD contents on your PC, and has meters for signal, SWR, and power. This can be seen in operation here: https://www.youtube.com/watch?v=lr-OomSTS7U Anyone wishing to try this out, then it can be found here: https://github.com/sipsmi/qmxwidget It's just proof of concept at the moment, and I will get around to tidying it up, but it works and I find it useful. 73 Simon G0FOZ

Does anyone use Solder pots for tinning and removing the enamel from the toroid leads? Any hints and tips? I see a cheap one on Amazon for about $20. Any suggestions if I should buy special solder for this, or use my normal Kester 63/37 solder in it?