Keyboard Shortcuts
ctrl + shift + ? :
Show all keyboard shortcuts
ctrl + g :
Navigate to a group
ctrl + shift + f :
Find
ctrl + / :
Quick actions
esc to dismiss
Likes
Search
error: message
|
Andy Cutland
Hi John,
toggle quoted message
Show quoted text
Are you including a space after your suffix. If you are then take it out. 73"s De Andy ------------------------------ On Mon, Jul 29, 2013 12:59 PM PDT John Randall wrote:
Trying to run the hardware in wspr mode, but keep getting error : message. Any ideas as it happens with no message or with one. |
|
Hans Summers
Hi John The requirements on callsign entry for WSPR are on page 4 of the manual (v2.03).? WSPR will try to take your callsign from the "Callsign" setting and will make sure it satisfies the listed callsign requirements for WSPR. If the callsign is empty or invalid (doesn't satisfy the right format for WSPR) then the kit will try to use the "Message" parameter instead, in case you have put your callsign in there. If that is empty/invalid too then you will get that error message "Error: Message".?
In your case you must just enter "M0ELS", and as Andy says, NO space character at the end. (Unnecessary note: you could put a space character at the beginning, and it would be fine, i.e. " M0ELS". But if you do not, the kit will put one in automatically).
73 Hans G0UPL On Mon, Jul 29, 2013 at 8:59 PM, John Randall <m0els@...> wrote:
|
|
John Randall
No space in? callsign window M0ELS, but put spaces in the message window? M0ELS JO01 27 73 John ? Digitally signed mail - M0ELS From: Andy Cutland To: qrplabs@... Sent: Monday, 29 July 2013, 22:49 Subject: Re: [QRPLabs] error: message
?
Hi John, Are you including a space after your suffix. If you are then take it out. 73"s De Andy ------------------------------ On Mon, Jul 29, 2013 12:59 PM PDT John Randall wrote: >Trying to run the hardware in wspr mode, but keep getting error : message. Any ideas as it happens with no message or with one. > >CW mode brings up the clock >00 WHICH IS COUNTING DOWN i PRESUME TO TX MODE. > > >73 >John > >? >Digitally signed mail - M0ELS |
|
Hans Summers
Hi John In that case, you have to put your callsign "M0ELS" into the "Callsign" setting, and it will be used for WSPR. 73 Hans G0UPL
On Tue, Jul 30, 2013 at 8:48 AM, John Randall <m0els@...> wrote:
|
|
Hans Summers
Hi John? To be clear: I think you have put in your callsign, locator and power into the Message setting. This is not what is needed for WSPR! You need: 1) "Mode" set to "WSPR" 2) Your callsign in the "Callsign" setting; or your callsign alone in the "Message" setting
3) Locator in the "Locator" setting 4) Power in the "Power" setting. 73 Hans G0UPL On Tue, Jul 30, 2013 at 8:48 AM, John Randall <m0els@...> wrote:
|
|
John Randall
I managed to get it running, by deleting the message contents Hans. Now got it running with my transverter and output was originally not enough to drive the transverter, until i switch my hf rig off.....hi. Now got 10w out on transverter. Probably some earth loop cause and effect. Now I need to build a receive converter to fit inside the same box. Thanks John ? Digitally signed mail - M0ELS From: Hans Summers To: QRPLabs@... Sent: Tuesday, 30 July 2013, 15:30 Subject: Re: [QRPLabs] error: message
?
Hi John? To be clear: I think you have put in your callsign, locator and power into the Message setting. This is not what is needed for WSPR! You need: 1) "Mode" set to "WSPR" 2) Your callsign in the "Callsign" setting; or your callsign alone in the "Message" setting
3) Locator in the "Locator" setting 4) Power in the "Power" setting. 73 Hans G0UPL On Tue, Jul 30, 2013 at 8:48 AM, John Randall <m0els@...> wrote:
|
to navigate to use esc to dismiss