开云体育

*" . . . a carpenter building two new 90 x 270cm tables . . . "* If you can procure motorized leg sets locally, consider having these built as standing desks. Your team will greatly appreciate them.

Yes, I also confirm the new 017 is alive and working! I'm very excited to try out the new AGC functionality!? Thanks Hans! 73 Roy - KI0ER

Except that the COM access and the virtual directory do not appear any more....... Bev COAA

Hans, That fixed it. Tnx! Paul, W9AC Sent: Friday, February 16, 2024 10:20 AM To: [email protected] Subject: Re: [QRPLabs] #qmx #firmware 1_00_017 AGC, S-meter, LPF sweep Hi Roy,

That seems to be working now Hans :)

Hi Roy, all Profound apologies are hereby offered. I would love to be able to tell you that I just fired the entire development time however, I already fired them last time. Embarrassment...

I was able, using the wire jumper, to roll back to 016 Firmware, and my darling QMX appears happy again. It's nice that one only needs to remove the 2 bottom screws on each side of the enclosure to

Hi Hans, In IQ enabled, digital mode the Signal strength meter is not display.? On my QMX it only displays the Signal strength in CW mode with IQ set as disabled.? Don't know if this is by

Hi All, I have a rev 3a QDX (80-20 model, firmware 1.10) that I built back around 10/2022. I used it more or less continuously for 6mo after building it, with great results. I wrapped T1 for 12v and

Looks like it's still available or at least it's current iteration. Rigol DS1102Z-E - Two Channel / 100 MHz Digital Oscilloscope https://a.co/d/i9XyKEG Roy WA0YMH wrote:

Hi Roy Yes I deleted 1_00_017 from the page... There's a division-by-zero someplace when the new parameter settings are zero. Ouuuuffff... OK I am figuring it out then I will stop that... 73 Hans

Hi Hans. Hopefully you'll pull the release from the QMX page until this gets figured out. My QMX does show up with it's USB Serial Device (COM4 in my case). But PUTTY won't connect to it. PuTTY

OK... I nearly found it... WAIT... 73 Hans G0UPL http://qrp-labs.com https://www.buymeacoffee.com/g0upl [email protected]> wrote:

Hans, I do have a few of these to overnight to you if your looking for quality soldering irons that last and need quickly ? Just trying to help......

Hmmmm Interesting... well best people WAIT a little bit... while I think... 73 Hans G0UPL http://qrp-labs.com https://www.buymeacoffee.com/g0upl

Yes - this is my issue.? It did boot to what looked like to be a working state once however all controls were frozen.? On reboot it was back to this initializing state...

Same here… Sent: Friday, February 16, 2024 9:39 AM To: [email protected] Subject: Re: [QRPLabs] #qmx #firmware 1_00_017 AGC, S-meter, LPF sweep Hmm - apologies for the numerous

Hmmmm, I just followed the usual procedure to update the firmware to 17 and having placed the new file in the QMX pseudo-directory, the lights didn't come on again. I waited a while and eventually

Mine just got stuck there as well. Rev 2. I cycled the power and it got past it but was locked up. Cycled again and it gets stuck at that screen. Putty won't connect in either case. Brad W8BMO

I just upgraded the firmware to 017, and the display after it re-started just showed "A14.030.00P" followed by an battery icon indicating the battery was empty. It was in practice mode before the