开云体育

Hi All, I got my QDX up and running today but not getting any takers at my 4.2W.? Well, I ordered a 50W Amp to use with the QDX.? It went out a few days after I ordered the QDX back on Oct 16th.?

*50106* landed today in Alabama, from Kansas. ?In 3 days. Aug AG5AT

Hi, As this is my first QRP Labs kit I an not sure how to proceed. I started with the 10M LPF kit. After winding the inductors I decided to measure them and was surprised with the results. I am sure

The 37 refers to the diameter in inches ie. 0.37" and the 2 or 6 refers to the "mix" of the powdered iron toroid. Type 2 works best below 10MHz and Type 6 works well from 3-40 MHz. Type 7 is popular

The toroids for L1? - L4 are red and yellow and I think they are T37-2 and T37-6 types: not sure about this. I don't know the technical nomenclature or the color coding standard is for describing

Alan, I hope people that have this issue don't force it cuz it could peel the IC right off the board and pads with it. All the IC's on this board are packaged in a thermal plastic and file easily with

Wolfgang, Right! I have just checked the other PCB, it is the same. The design clearance is minimal, the cuts in the master board are not quite aligned so the components are off-centre. It is only

Same issue with mine... Going to need to file just a bit off of IC7 package to get it to slide into the case or scoot the chip inwards ever so slightly but will likely opt to take a bit of plastic off

Not out of minis Mike... More than 900 in stock 73 Hans G0UPL http://qrp-labs.com

Mike, I like your standoff idea. It’ll offer at least a little protection. I don’t understand why QRP Guys doesn’t add a 3D printer guy to their group and sell cases alongside their handy

Alan, it will not solve *your* problem, sorry, but at least, that how it looks like, if all is OK 73's de OE1MWW Wolfgang

Yep. Same problem with mine but it will fit into one half ok and then other bit becomes the lid as it were. Not built yet but after seeing posts I chec ked. 73 Roger G4IUP.

Today I have used it for about 8 hours Stopped working 2 times First time - this vertical bars you can see in an image 2-3 messages over. After pressing "Test Cat" - all was ok again. The next time -

I think a photo will be necessary. I had zero issues on my QDX, which you can see in part 15 of the series linked below. Does yours not look the same as mine? https://youtu.be/GK37eBYvlp4?t=72 -- Ryan

When trying the PCB in the supplied case I find I cannot fit it. There is insufficient clearance for IC7 whatever way or case segment I try. This is the same for the two kits I have. IC6 opposite does

Hi All Using the calculator you can also input value of series capacitor (assuming 80M=220pf,20M=22pf ) to show resonant frequency ,80m =3.73Mhz 20M=25.5 Mhz ? requires 72pf to resonate at 14.074 Mhz.

I put it on standoffs for now until I find a suitable case. One slightly annoying and inexplicable (so far) feature is that when switched to dummy load, the circuit still includes the antenna in

Hi Evan, CAT and other options are all set exactly as the manual states. :) -- Ryan Flowers - W7RLF MiscDotGeek - QRP and More (Website) ( http://miscdotgeek.com/ ) *QDX* News, Tips, Build Series

Also, there is always the possibility of accidentally shorting turns together. 73 de Lee KX4TT

Thank you Ryan for the response.? Based on that information, the command to drop the PTT line is being missed by the QDX.? This could be a software issue on the QDX side that it cannot decode the