开云体育

Turnigy makes a good product and I've used a lot of their packs... However read the information its 2.2AH 1.5C? that means the max current is about 3.3A and standard .5C charge rate. For QCX that's

I found this on Amazon today: https://www.amazon.com/dp/B00USRD91W/ref=cm_sw_em_r_mt_awdb_4muTCbG8JHMRP It's a 3s li-po 2.2Ah pack w/ protection built in for under $25! Seems like a great option for

Section 3.16 of manual Install 1uF capacitors (3). I measured two caps at 0.978 uF I measured one cap at 0.775uF . About - 22% tolerance Should I install the low cap??? Thanks, -- Al Lipinski

Hi all, I run a couple of the QRP Labs on different bands and have found the output on say 80M and 160m were very good. More than 5 watts. In fact on 80m it will bury the needle on my Oaks Hills set

Almost forgot -- in order to do this APRS stuff you need some JS8 stations set up to forward (via the internet) any received JS8 messages that contain the APRS flag.? I don't know how many JS8

Again, this is an older topic, but with JS8 you can do way more than APRS position reports.? You can send arbitrary telemetry data, not only to the APRS network, but you can use the APRS email and

I'm afraid I've tried this. The calibration is now set to Step 01, Time 060, but the step size was larger initially. The frequency has more or less stabilized to 26,998,733 which should be about

One other thing, are you using the gps to calibrate the u3s? The OCXO oscillates at a lower frequency, maybe the OCXO is set correctly and it's working it's way to its settled point. I use a big

Love what Andreas, DM5MU did with those plug-in modules ! Very nicely-done six-band QCX rig, Andreas ! Tnx & 72 / 73, Bill, N4QA

When I was using the plain old Si5351A synthesiser module (no GPS correction) I was getting drift reports of 0 or 1 - it was very stable. My U3S is in the aluminum case but I have a LM7805 voltage

Thank you, Alan...I'll have a look ! 72 / 73, Bill, N4QA

Bill, There are a couple of reports of multi band builds here on the web / forum, a search should find a few different ideas / implementations. One such build is also shown in the builders gallery

Hello Nigel. Thank you for your kind comments ! Sounds like your QCX-30 will be a very handsome rig ! Looking at the? QCX schematic, I am considering lifting one end each of C27 & C28, and jumpering

Hi Andy, Thanks for the reply. Yes, I set up just like you describe. But I am still afraid that I didn't quite hit the sweet spot because of the drift I am seeing.? The fact that I am seeing negative

*DOH!* What a dummy. I forgot to change the calibrate step time on this U3S kit - I did go through this on U3S #1 but completely forgot on #2. Now we are calibrating and the reference frequency is

I received my QCX kit it a couple of weeks which I ordered on 3-16. But the extra QCX programmed ATMEL chip which was ordered on 3-18? hasn't left Turkey or shown any movement since 3-22 Joe

Greetings from sunny South Africa Bill :-)? VERY interesting report back from your QCX adventures! Many thanks for sharing - I for one sincerely appreciate, thank you. Sooooooo, I have yet to start

Hi Sverre,? I have built 4 of the OCXO, how did you set the OCXO up? Mine are all inside a qrp-labs.com case with no issues.? I used Argo software and a FT 817ND as receiver with a lead from spk out

Exactly. You can always define another instance of the Serial object. FWIW, I would leave pins 2 and 3 open on the Uno/Nano, as those are the only external hardware interrupt pins and I usually avoid

I had the same problem with my 30m QCX. -- 73 Richard G4TGJ