开云体育

Well obviously the next one will be a multi-band SDR with SSB, 7 inch TFT touch screen, ...something that will have the big three shaking in their boots ;) Greg K1YW

I ended up making my own case using an extruded aluminium enclosure from Bangood. I must say, it took about 19 hours of work for the case alone, having messed up the powder coating while doing the

My QCX 40 ordered ?early June and mailed 7/9/18 arrived 7/24/18 from Turkey. Looking forward to building this version.? Gary K4VIG

I'm not sure! In fact I'm sure there must be something wrong otherwise it would be working. I've taken some readings again, this time with the internal volt meter. All the ICs look fine - some of the

Richard, Are you sure there is not another bad connection? I'm not sure if voltage readings are reliable for checking all connections. And are you sure the windings are in the same direction?

Look at??/g/QRPLabs/message/25129? 72!? Jirka OK1IEC

I took voltage measurements and got a very strange result on T1. 4 connections should be at 0V and 4 at 2.5V, but 1 was at 3.5V! So clearly the enamel hadn't burnt off despite my best efforts. I put

Thanks Hans, Yes thought I'd seen one somewhere. The link to the files is https://www.thingiverse.com/thing:2661221 Nice thing is he added an opening for the microswitch CW key that the metal case

Hi Dom There's at least one 3D printed design out there, and the files are on thingiverse, have a look in the QCX builders' gallery http://www.qrp-labs.com/qcx/qcxgallery.html for Dave G8XUL. 73 Hans

Hi all, Had a QCX for a while now (30m) and got one of the cases from a DL source but was wondering is there any appetite for a 3D (ie GCODE/STL) version of a case. Not found one in the files section

I am sure there are many QCX still to come otherwise retirement or a multi band QCX ? 73s Martin DK3UW

Hi Dave I'm not ready to answer that question yet ;-) Stay tuned ;-) 73 Hans G0UPL http://qrp-labs.com [email protected]> wrote:

Hans, Since these kits are your main income eventually the whole world will have a QCX. Then what? What is in the works to keep the income flowing to feed those new lab assistants? Dave K8WPE

Hello Hans, It probably does. If that is explained in the manual I missed it (always possible with me) and I never thought to set frame to something less than the message length. I will try that. I

Hello Chris, Paul Although the shipment backlog is cleared, my plate is not - it is still very full! The next 2 months are looking very busy :-( Paul, regarding frames longer than 60 minutes because

Gang, A few weeks ago I built up the QCX kit for 40m which I had puchased at FDIM Vendor night. ?All worked well initially, though I did have to remove a few turns from T1 to get the trimmer cap in

Joe Stick with order in the instructions, even where it may buck tradition. It is a tightly packed board, with resistors standing up. Key hint is to set your pc screen next to the board. The labels

I ordered 1 case and 1, 100e upgraded chip on June 29, 2018.? I received an email that both had been shipped on July 9th.? I received both of them today, in Warren, Michigan (USA) July 24th, 16 days

Hi Joe; I've built the QCX/20 & QCX/40 and presently building the QCX/30 kits. I found no issues installing T1 in accordance to the building instructions sequencing. I have found that if you take your

Richard, Yes , Double sided PCBs have their own Cons . But we should , once decided to remove a component, especially multi legged, I prefer to butcher the part but NOT MY board. eg, resistance i