开云体育

I added a mono jack on mine or you can use a stereo to mono adapter like this (

It might be interesting if someone would write a set of test programs that supported individual function testing. In this case the code would activate only CLK-2 on the Si5351a and thus allow signal

Hi Robin. I have experienced this with other setups as well. A mono plug in a stereo socket will cause the ring and ground of the socket to short, thus keying a "dah". Its simple to a stereo

I have built #585 and the receive section is working along with the display and the sub menu items. The rig aligned as per the manual. The keyer and side tone are working. ? However, the

Ian, I did some measurements on my U3S with OCXO tonight. Calibrated a warm TS590S (TCXO) on air 5MHz and to my rubidium 10MHz to within 1Hz in WSJT-X. Condx bad for 30/20m beacons tonight. Listened

Shirley KE1L wrote... Thanks for the encouragement. I started with the 80M QCX. I hear those ones are easier to wind - hi! I think I'll wind the toroids for the 40M version first (half way done)

Dave G3WUN wrote... It started some months ago when I viewed a view videos that made hot air tools & SMDs to be not quite as difficult to use as most of us think they are. I went looking for an SMD

Good point Jim, I agree 100%. To: [email protected] Sent: Wednesday, December 6, 2017 3:55 PM Subject: Re: [QRPLabs] FT8 for U3? Come to think of it...this is QRP Labs and about the U3S

Come to think of it...this is QRP Labs and about the U3S kit.Lets remember what QRP is ... QRP operation is not 20,30.40.50+ watts like QSO modes are usually abused.When I say abused I mean 30+ watts

Hi Keith, There are about 30 SMD devices including two 8-lead ICs (not as close a lead pitch as the FST3253 as used in QRP Rx ).? R's and C's are 0805 , with four SMD can-type electrolytics.? The

Dave G3WUN wrote... http://www.multus-sdr.com/index.php?main_page=product_info&products_id=181 Just curious... are the the MultusSDR kits just the circuit boards and parts... i.e. you get to solder

Thanks Martin, got a 17 and 20 mtr to box up, glad I have a good stash of beer!! Cheers 72/3 Ian G4GIR

Most of the toroids are easy. The only challenging one is T1; it takes a bit of work to get all the wires in the right holes.

Great !? I've been hoping it would be added.? Will v3.13 be available soon? To: [email protected] Sent: Wednesday, December 6, 2017 9:52 AM Subject: Re: [QRPLabs] FT8 for U3? Hi Dean I already

Vernon VE1VDM wrote... I didn't print any of the manuals. I just opened them up on a tablet (iPad) and used it while working on the QCX etc. I'm about half way through the second one, but haven't

But how intrusive would an FT8 beacon be with such low power? Everytimne a new mode comes out,all rush to it while other modes are left for dead. See JT9 activity or Opera...slowly going away. I find

Very nice! Martin G0PJO Sent: 06 December 2017 17:55 To: [email protected] Subject: [QRPLabs] QCX 30 Complete Hi all Finished the complete build of QCX 30. Hopefully a pic will

Good idea John, I have a few trimmers in the junk box that will do the job and it might give an idea how much extra inductance is required so I can calculate the number of turns required Thanks Robin

After 30 years of no activity, I am still learning CW with a straight key which I shall continue to use for the time being. I recently completed the building of the 80m of the QCX and it is

Hi all Finished the complete build of QCX 30. Hopefully a pic will accompany this message. The enclosure is an RS Pt No 411-6632 TS1 sloping front panel, 58 mm rear height and 35 mm front